▼
Scroll to page 2
SON4 - 10 Tone Sounder & Bulb Beacon ‘Sonora’ 24vdc SON4 Bulb 77,00 - 86,00 + S2 S3 SON4 Bulb DC Stage 2 Stage 3 24,115, 230vac L~ Ø6,00 102,00 86,00 86,00 INSTALLATION INSTRUCTIONS 86,00 SON4 Bulb AC 98,00 N~ C S2 S3 Stage 2 Stage 3 SON4B 24vdc unit is CPD Compliant. Voltage : Voltage range : Current mA : 24vdc +/-25% 95mA* EN54-3 Type B 24vac 50/60Hz 115vac 50/60Hz 230vac 50/60Hz Stage1 tone Fre que ncy De s cr iption +/-10% +/-10% +/-10% Tone 1 Tone 2 800/1000Hz @ 0.25 sec Alternating 500/1200Hz @ 0.3Hz 0.5 sec Slow Whoop Tone 3 Tone 4 1200/500Hz @ 1Hz - DIN / PFEER P.T.A.P. 544Hz (100mS)/440Hz (400mS) - NF S 32-001 Tone 5 Tone 8 1000Hz Continuous 2400/2900 @ 50Hz sw eeping 180mA 50mA 30mA IP55 The tones listed have been tested to EN54-3 and are compliant with the Construction Pro duct D irective 89/106/EEC. EN54-3 te st data : document D0665 * Current at nominal voltage on Tone 1. >100dB(A)@1m ISN0606-B No liabil ity i s acce pted for an y con sequen ce of the u se of this docume nt. T he tec hnica l spec ifica tion o f thi s unit is sub ject t o chan ge wi thout notice due to our policy of contin ual product devel opment . All dimen sions are app roxima te.Thi s uni t is sold su bject to ou r stan dard condit ions of sal e, a c opy o f whic h is a vaila ble on reque st. Tel : +44(0)2087438880 mail : [email protected] Fax : +44(0)2087404200 web : www.e2s.com Stage1 Frequency Stage2 Stage3 tone Description (S2) (S3) Tone 1 800/1000Hz @ 0.25 sec Alternating Tone 8 Tone 5 Tone 2 500/1200Hz @ 0.3Hz 0.5 sec Slow Whoop Tone 3 1200/500Hz @ 1Hz - DIN / PFEER P.T.A.P. Tone 1 Tone 1 Tone 8 Tone 8 Tone 4 Tone 5 544Hz (100mS)/440Hz (400mS) - NF S 32-001 1000Hz Continuous - PFEER Toxic Gas 554Hz Tone 1 Tone 2 Tone 6 Tone 6 Bell Tone 1 Tone 8 Tone 7 Tone 8 800/1000Hz @ 7Hz Sweeping Tone 5 Tone 1 Tone 5 Tone 1 Tone 9 Tone 10 2400/2900Hz @ 50Hz Sweeping 420Hz @ 0.625 sec Australian Alert 500-1200Hz 3.75sec /0.25sec. Australian Evac. Tone 10 Tone 6 Tone 5 Tone 5 Tone 1 Tone 2 Tone 4 Tone 5 Tone 6 Tone 7 Tone 8 Tone 9 Tone 10 Fig 1. Tone 3 • • Tone selection. To select a tone place the pin link in the position shown above (Fig. 1). Sélection de la tonalité / réglage des commutateurs. Pour sélectionner une tonalité, mettre les socles à broches dans les positions illustrées (Fig. 1). • Tonwahl / Einstellung der Schalter. Zur Wahl eines Tons die Klemmenanschlüsse in die angegebenen Positionen bringen (Fig. 1). • Selezione tono / regolazione commutatore. Per selezionare un tono, disporre i collegamenti a cavallotto nelle posizioni indicate (Fig. 1). • Seleção de tons / ajuste dos comutadores. Para seleccionar um tom, coloque as ligações dos pinos na posição mostrada (Fig.1). • Selección Tono / programación interruptores. Para seleccionar un tono colocar las conexiones de los puentes en las posiciones mostradas (Fig. 1). • Toonselectie. Om een toon te selecteren de pinverbinding in de hierboven aangetoonde positie plaatsen (Fig. 1) • • • Valg af tone. Valg af en tone sker ved at anbringe stiftforbindelsen i ovenstående position (fig.1). Velge tone . For å velge en tone må du plassere stiftleddet i posisjonen som vist ovenfor (fig.1). Tonv al. Välj en ton genom att placera stiftanslutningen i läget som visas ovan (fig.1). •Volume Control •Réglage du volume •Steuerung der Lautstärke •Controllo volume •Controlo do Volume •Control Volumen •Vol umen kontrol •Vo lum ereg eli ng •Vo lum kon tro ll •Vo lym kon tro ll