A25-M
[email protected]
SWISS MADE BY RELEC SA 1400 YVERDON
www.psiaudio.com
Technical data sheet
PSI AUDIO
A23-M
PSI A23-M s1 / typical characteristics subject to change without prior notice / © RELEC SA.
A23-M
[email protected]
www.psiaudio.com
SWISS MADE BY RELEC SA 1400 YVERDON
All measurements in anechoic room
acoustical axis at 1 meter
POWER
PSI Audio Hand Made
Neodymium Tweeter
AOI*
CPR*
HP
PSI Audio Hand Made
Neodymium mid
POWER
G
AOI*
HP
*C P R : Compensated Phase Response system.
*A O I : Adaptive Output Impedance system.
*PSC : Phantom Standby Control.
POWER
G
LEVEL
INPUT
1=Gnd
2=Hot
3=Cold
ROLL OFF
HP
LP
LIMITER
AOI*
LP
PSC*
TEMP. SENS
Hi. ± 57V
115/220V
Flow Guide
Low ± 18V
POWER
LIMIT
MAINS
EMI LP
ON/OFF
[dB]
FUSE
TRANSF.
RECT.
STANDBY
REG.
SPL@-10dBu/1m A23-M
-10dB Roll Off
+10
140+70+50 W
260 W
Sym, 10k Ohms
0.775 V
8 dBA
0
-10
-20
-30
20
50
1k
500
200
100
[dB]
2k
5k
10k
20k [Hz]
2k
5k
10k
20k [Hz]
2k
5k
10k
20k [Hz]
THD@-10dBu/1m A23-M
-20
24 Vpp / 20.7 dBu
-30
109 dB
-40
120 dB / peak 123 dB
-50
34 - 23000 Hz
-60
20
±1.5 dB (39Hz - 20kHz)
< 1% (100Hz-20kHz)
50
1k
500
200
100
[Deg]
ACOUSTIC PHASE A23-M
+540
±45° (220Hz - 20kHz)
+450
+360
90° x 80° (H x V)
+270
+180
3 Way(s)
+90
620Hz, 3.2kHz
-90
0
-180
20
50
1k
500
200
100
Ø 210 mm / Ø 170 mm
Ø 120 mm / Ø 56 mm
[dB]
Ø 100 mm / Ø 25 mm
120
1 x XLR F / 3P
110
1=GND, 2=(+), 3=(-)
MDF
Max Continuous SPL 1m A23-M
130
100
8k
10k
12k5
16k
10k
12k5
16k
6k3
6k3
8k
4k
5k
5k
3k15
3k15
4k
2k
2k5
2k5
1k6
5
2
PSI A23-M s1 / typical characteristics subject to change without prior notice / © RELEC SA.
1k25
1k
800
630
500
400
315
250
200
160
125
100
80
63
50
1
40
Humidité moy / max
< 75% / < 90%
Mean / Max Humidity
Température externe
5 - 40 °C
External Temperature
Directivity Factor A23-M
10
31
Tension de secteur
115/230V±10%(50-60Hz)
Voltage
Consommation
1.8 - 8 - 200 W
Consumption Standby-Idle-Max
2k
[Q]
18.0 / 20.2 Kg
1k6
1k
280 x 500 x 340
1k25
800
630
500
315
400
250
200
125
160
100
63
80
50
31
40
25
90
25
Puissance RMS
RMS Power
Puissance programme
Program Power
Impédance d'entrée
Input Impedance
Sensibilité pour 100 dB @ 1m
Sensitivity for 100 dB @ 1m
Bruit propre, 1m, champ libre
Self-Generated Noise, 1m, Free Space
Saturation d'entrée
Input Overload
Niveau max. continu (single), 1m
Continuous Max SPL (single), 1m
Niveau max. programme (pair), 1m
Program Max SPL (pair), 1m
Réponse à -6 dB
Response at -6dB
Tolérances
Tolerances
Distorsions THD
Distortion THD
Tolérances de phase
Phase Tolerances
Dispersion (B.R. 4 - 16 kHz) à -6 dB
Dispersion (P.N. 4 - 16 kHz) at -6 dB
Système
System
Fréquence de coupure
Crossover Frequency
Dim. basse ext. / membrane
Woofer's Dim. Ext. / Diaphragm
Dim. medium ext. / membrane
Medium's Dim. Ext. / Diaphragm
Dim. aigue ext. / membrane
Tweeter's Dim. Ext. / Diaphragm
Connecteurs
Connectors
Entrée du signal
Signal Input
Matériaux du boîtier
Box Material
Dimensions du boîtier L x H x P mm
Cabinet Dimensions W x H x D mm
Poids brut / net
Gross / Net Weight
A23-M
[email protected]
www.psiaudio.com
SWISS MADE BY RELEC SA 1400 YVERDON
All dimensions are in mm
Mounting
230
Gravity
center
500
Front
Minimum well-aired space
160
Front
280
70
Bottom view
340
Side view
Refer to user manual for information about installation and safety instructions
Acoustical axis
140
150
390
380
Front view
Mid/High baffle orientation
As mentioned on the drawing here above, you can change the
orientation of the mid/high baffle. Before this change,
the power cable must not be connected. Be sure that this operation
does not cause any short-circuit to the connections of the baffle.
Measurement environment: Large anechoical room
Temperature 23±2°C
Humidity 50±20%
PSI A23-M s1 / typical characteristics subject to change without prior notice / © RELEC SA.
">
