Allen-Bradley CuAl Terminal Lugs (1x2/0) Guide d'installation

Bul. 140G/140MG
DIR 1000719R0821 Version 02 - 140G-G-TLA13, 140G-G-TLA14, 140G-H-TLA13, 140G-H-TLA14
CuAl Terminal Lugs (1x2/0) for 140G-G, 140G-H, 140MG-G, 140MG-H
Terminali per cavi (CuAl)
Anschlüsse für Kabel (CuAl)
Prises pour câbles (CuAl)
Terminales para cables (CuAl)
电缆端子 (CuAl)
Installation - Installazione - Installation - Installation Instalación - Instalação WARNING: To prevent electrical shock, disconnect from power source before
installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA 70E requirements
Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden.
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation
secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire
appropriée. Protéger le produit contre les environnements agressifs.
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes.
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes.
140G-H
140MG-H
1
140G-G
140HG-G
CLACK
A
B
Lug
Lug
C
D
End cap kit End cap kit
E
Screw
Required
Tools
xx lb-in
xx Nm
5/32"
5/32"
LENGTH Thread
0.25" (6mm) #6-32
LENGTH Thread
0.25" (6mm) #6-32
3p
3
-
3
-
3
4p
4
-
4
-
4
3p
-
3
-
3
3
4p
-
4
-
4
4
LENGTH
M
8 mm (0.31 ") M5
SL
140G-G
xx lb-in
xx Nm
140G-H
Publication 140G-IN193C-EN-P April 2024
CH 5
2
Copper-Aluminium (CuAl) terminal lug installation 140G-G, 140G-H, 140MG-G, 140MG-H
1 140G-G
C
3
2
13.3 lb-in
1.5 Nm
E
A
30.1lb-in
3.4 Nm
min 0.55”
min 14
5/32"
1
10AWG...8AWG = 40 lb in / 4.5Nm
6AWG...2/0AWG = 80 lb in / 9Nm
4mm2...6mm2 = 40 lb in / 4.5Nm
10mm2...70mm2= 80 lb in / 9Nm
Stranded
No of Poles Screw Head Type Wire Type AWG Wire Range Metric Wire Range (mm2)
Catalog No
140G-G-TLA13
140G-G-TLA14
3
4
Hex
Cu/Al
10…2/0
D
2 140G-H
2
In < 50A
3
E
30.1lb-in
3.4 Nm
Flexible
In ≥ 50A
WARNING: These lugs are only to be used with devices
In = 50A or greater. The improper use of these lugs with
devices less than In = 50A could cause overheating,
arcing, or in a hazardous environment, an explosion
13.3 lb-in
1.5 Nm
B
4…70
5/32"
4mm2...6mm2 = 40 lb in / 4.5Nm
10mm2...70mm2= 80 lb in / 9Nm
min 14
10AWG...8AWG = 40 lb in / 4.5Nm
6AWG...2/0AWG = 80 lb in / 9Nm
min 0.55”
1
Stranded
Catalog No
Flexible
No of Poles Screw Head Type Wire Type AWG Wire Range Metric Wire Range (mm2)
140G-H-TLA13
140G-H-TLA14
3
4
Hex
Cu/Al
10…2/0
4…70
For Technical Support, visit rok.auto/support.
Rockwell Automation maintains current product environmental compliance information on its website at rok.auto/pec.
Product certificates are located in the Rockwell Automation Literature Library: rok.auto/certifications.
EEE Yönetmeliğine Uygundur.
TM
expanding human possibility
AMERICAS
EUROPE/MIDDLE EAST/AFRICA
ASIA PACIFIC
Publication 140G-IN193C-EN-P April 2024
Copyright © 2021 Rockwell Automation, Inc. A
l l Rights Reserved. Printed in USA.
DIR 1000719R0821 (Version 02)
ECN000351272
">