Vedette VDM8CW Sèche-Linge Hublot Manuel du propriétaire

PDF
Document
Vedette VDM8CW Sèche-Linge Hublot Manuel du propriétaire | Fixfr
/

User questions

C A

Robert C.

Where are the condenser and humidity sensors located?

The condenser is behind the plinth; open the plinth and unlock the two condenser cover latches, then remove the condenser by holding its plastic part. The humidity sensors are inside the appliance; their metal surfaces can be wiped with a soft cloth moistened with white vinegar after the appliance has cooled.

C A

Robert C.

What are the installation and connection requirements for the dryer?

Place the appliance on a stable, level surface, leave at least 3 cm clearance under a worktop and do not cover ventilation openings. Use a 220–240 V, 50 Hz grounded socket protected by a 16 A fuse. For direct drainage, install the drain hose at a maximum height of 80 cm without kinks. Stacking requires a special kit and a washing machine of equal or greater capacity.

C A

Robert C.

What are the installation and connection requirements for a tumble dryer?

Installation requires a stable, level surface, adjustable feet, at least 3 cm clearance from walls or under a worktop, unobstructed ventilation openings, and ambient temperature between +5 °C and +35 °C. Electrical connection must be 220–240 V, 50 Hz, on a grounded socket protected by a 16 A fuse, without extension leads or adapters. The drain hose must be at a maximum height of 80 cm and must not be kinked. A dryer may be stacked only on a washer of equal or greater capacity using a special stacking kit.

C A

Robert C.

What are the installation and connection requirements for a tumble dryer?

Place the appliance on a stable, level surface, adjust the feet, keep at least 3 cm clearance from side/rear walls and under a worktop, do not block ventilation openings, use it between +5 °C and +35 °C, and do not install it behind a door that prevents full opening. Connect it to 220–240 V, 50 Hz on an earthed socket protected by a 16 A fuse, without extension leads or adapters. For drain connection, use the supplied hose at a maximum height of 80 cm without kinks. When stacking on a washing machine, use a compatible stacking kit and ensure the floor can support the total load.

C A

Robert C.

What are the installation and connection requirements for a tumble dryer?

Place the appliance on a stable, level surface against a wall and check balance with a spirit level; adjust the adjustable feet if necessary. Leave at least 3 cm clearance between the side or rear walls and the underside of the worktop if installed under a worktop. Do not cover the ventilation grilles or the front air-intake opening. Use the appliance within a temperature range of +5 °C to +35 °C. Do not install it behind a lockable or sliding door, or a door whose hinge prevents the door from opening fully. Electrical connection: the appliance is designed for 220–240 V, 50 Hz; connect it to an earthed socket protected by a 16 A fuse, in accordance with the rating plate; do not use an extension lead, multi-socket adapter or plug adapter. Water drainage: by default, condensation water collects in the tank; the supplied drain hose can be connected to drain water directly; the drain hose must be installed at a maximum height of 80 cm and must not be kinked or raised between the outlet and the machine. Stacking: the dryer may only be placed on a washing machine of equal or greater capacity; a special stacking kit is required.

C A

Robert C.

Where are the condenser and humidity sensors located on a VEDETTE VDM8CW dryer?

The condenser is behind the plinth; access requires opening the plinth and unlocking the two latches of the condenser cover. The humidity sensors are located inside the machine.

C A

Robert C.

How is a VEDETTE VDM8CW dryer installed and connected?

Place the dryer on a stable, level surface and adjust the feet; leave at least 3 cm clearance at the sides/rear and under a worktop, and do not cover ventilation openings. Use it between +5 °C and +35 °C. Connect it to a 220–240 V, 50 Hz earthed socket protected by a 16 A fuse, without extension leads or adapters. For direct drainage, install the drain hose at a maximum height of 80 cm without kinking or raising it between the outlet and the machine.

Preparing document for printing…
0%