Siemens WT45HV03FF Sèche linge pompe à chaleur Owner's Manual

PDF
Document
Siemens WT45HV03FF Notice d'utilisation | AI Chat | Fixfr
/

User questions

F S

Mary F.

How to disable the acoustic signals on a dryer?

To disable the acoustic signals, follow these steps: 1. Turn on the device and set the program selector to position 1 (Cotton) for 5 seconds. 2. Press and hold the Start button while turning the selector to position 2 (note: this position displays the spin speed, e.g., 600 rpm, and is not used for volume adjustment). 3. Turn the selector to position 3 and use the 'Finish in' or 'Drying time' button to set the end-of-program signal volume to 0. 4. Turn the selector to position 4 and set the button signal volume to 0. 5. Turn the selector to the Off position to save the changes.

F S

Mary F.

How to disable or adjust the volume of the sound signals on the dryer?

To disable sound signals, enter the settings mode: 1. Turn on the device and select the Cotton program at position 1, then wait 5 seconds. 2. Hold the Start button and turn the dial to position 2. 3. Turn the dial to position 3 to adjust the end-of-cycle signal volume using the "End in" or drying time button (set to 0 for off). 4. Turn the dial to position 4 to adjust the button signal volume to 0. 5. Turn the dial to the off position to save the settings. Note: Position 2 displays spin speed and is not used for volume adjustment.

F S

Mary F.

How to adjust or mute the signal volume on the dryer?

  1. Turn on the dryer. 2. Select the 'Cotton' program (position 1) and wait 5 seconds. 3. Press and hold 'Start' while turning the programmer to position 2 (this display shows spin speed, not volume). 4. Turn to position 3 to display the end-of-cycle volume; adjust it to 0 (off) using the 'Finish in' or 'Drying time' button. 5. Turn to position 4 to adjust the button signal volume to 0. 6. Turn the programmer to the off position to save the changes.
F S

Mary F.

How to disable the beeps on the dryer?

To mute the signals, set the volume to 0. 1. Turn on the device. 2. Select the 'Cotton' program (position 1) and wait 5 seconds. 3. Press and hold 'Start' while turning the knob to position 2 (the display shows 600, which is the spin speed). 4. Turn to position 3 and use the 'Finish in' or 'Drying time' buttons to set the end-of-programme signal to 0. 5. Turn to position 4 and set the button signal to 0 in the same way. 6. Turn the knob to off to save.

F S

Mary F.

How to disable or adjust the volume of sound signals (beeps) on the dryer, and what to do if a setting confusion arises with spin speed?

To disable the beeps on your tumble dryer, the document indicates setting the sound volume to 0. Procedure:

  1. Switch on the tumble dryer.
  2. Select the Cotton program to position 1, then wait 5 seconds to activate the adjustment mode.
  3. Press and hold the Start button, and simultaneously turn the programmer knob to the right to position 2 (the spin speed is displayed).
  4. Turn the programmer knob to position 3: the volume of the end-of-program signal is displayed. Change it using the End in button or the drying time button until it reaches 0 (0 = off).
  5. Turn the programmer knob to position 4: the volume of the button signals is displayed. Change this also to 0.
  6. Turn the programmer knob to the stop position to save the settings. If the selector does not turn beyond position 2, ensure you are not holding down the Start button (it is only used to access position 2 at the start of the procedure): positions 3 and 4 are selected by normally turning the programmer knob.
F S

Mary F.

How to disable or adjust the beep volume on the dryer?

To disable beeps, set the volume to 0. Turn the dryer on and select the Cotton program (position 1). Wait 5 seconds, then hold the Start button while turning the selector to position 2 (spin speed). Turn the selector to position 3 for the end-of-cycle signal or position 4 for button signals. Use the 'Finish in' or 'Drying time' buttons to change the value to 0. Turn the selector to the off position to save.

F S

Mary F.

How to disable or adjust the volume of beeps and audible signals on the dryer?

Pour supprimer les bips sur votre sèche-linge, le document indique de régler le volume sonore à 0. Procédure :

  1. Mettez le sèche-linge en marche.
  2. Sélectionnez le programme Coton sur la position 1, puis patientez 5 secondes pour activer le mode réglage.
  3. Appuyez sur la touche Départ, maintenez-la enfoncée et tournez simultanément le programmateur vers la droite sur la position 2 (la vitesse d'essorage s'affiche). Note : le chiffre 600 affiché à ce stade correspond à la vitesse d'essorage et non au volume sonore.
  4. Tournez le programmateur sur la position 3 : le volume du signal de fin de programme s'affiche. Modifiez-le avec la touche Fin dans ou la touche pour la durée de séchage jusqu'à 0 (0 = éteint).
  5. Tournez le programmateur sur la position 4 : le volume des signaux des touches s'affiche. Modifiez-le également à 0.
  6. Tournez le programmateur sur la position d'arrêt pour mémoriser les réglages. Si le sélecteur ne tourne pas au-delà de la position 2, vérifiez que vous ne maintenez pas la touche Départ enfoncée (elle ne sert qu'à accéder à la position 2 au début de la procédure) : les positions 3 et 4 se sélectionnent en tournant normalement le programmateur.
Preparing document for printing…
0%