1) COUPER LA TENSION DE L’APPAREIL (alimentation, sorties, relais, etc.).
2) Extraire l’instrument de son boîtier.
3) En utilisant un aspirateur ou un jet d’air comprimé à basse pression (maxi. 3 kg/cm
2
) enlever toutes traces de poussière dans les fentes de ventilation et sur les circuits en faisant attention à ne pas endommager les composants.
4) Pour nettoyer les parties extérieures en plastique ou en caoutchouc, utiliser uniquement un chiffon propre et légèrement imbibé de :
- alcool éthylique (pur ou dénaturé) [(CH
3
- alcool isopropilique (pur ou dénaturé).
)
2
CHOH].
- Eau (H
2
O).
5) Contrôler que les bornes sont serrées à fond.
6) Avant de rebrancher l’instrument dans son boîtier, vérifier que l’appareil est parfaitement sec.
7) Rebrancher l’appareil est le mettre sous tension.
151
XKC-2-D2.pmd
151 06/04/2006, 16.14
The middle and lower display will show:
General notes:
A complete and consistent set of run time and configuration parameters is memorized in the instrument. These data are the typical values loaded in the instrument prior to shipment from factory.
With these instruments it is also possible to save the user run time and configuration parameters setting and load them again when necessary (for more details see "Default configuration and user parameters" at pag. A.6).
This instrument allows to load the default value of a single run time parameter group or to load all the run time parameters
(exception made for "Run time group 8" [r.Hxx] and "Run time group P").
A ) When it is desired to load the default parameter of a single group, proceed as follows:
A.1) By MENU pushbutton, select the desired run time parameter group.
A.2) By FUNC pushbutton, select the last parameter of the selected group.
A.3) By V or W pushbuttons, select the "On" indication on the central display.
A.4) Push the FUNC pushbutton.
The central display will show:
The default parameter loading procedure for the selected group is ended.
B) When it is desired to load the default value of all the run time parameters (exception made for "Run rime group 8"[r.Hxx] and "Run time group P"), proceed as follows:
B.1) By MENU pushbutton, select the "Run time group dF"
[r.Lxx].
B.2) Push the FUNC pushbutton.
The middle and lower display will show:
B.3) By V or W pushbuttons, select the "On" indication on the central display.
A. 1
XKC-A-D2.pmd
1 06/04/2006, 16.15
B.4) Push the FUNC pushbutton.
The middle display will show: and then it will show:
The default parameter loading procedure of all run time parameters is ended.
The following is a list of the default run time parameters loaded during the above procedure:
PARAMETER
SP
Pr.St
St.dY
St.tñ
DEFAULT VALUE
= Set point low limit ("rL" [r.E12])
= nonE
= ñon
= 0.00 h.mm
Run time group 3 [r.Cxx]
PARAMETER DEFAULT VALUE
ñ.rSt
AL1
= OFF
= Initial range value (for process alarm)
= 0 (for deviation alarm) bA1.L
= 0.0 (for control output alarm)
= 0
A. 2 bA1.h
AL2 bA2.L
bA2.h
AL3 bA3.L
bA3.h
AL4 bA4.L
bA4.h
A.L.Fd
A.H.Fd
HSA1
HSA2
HSA3
HSA4
XKC-A-D2.pmd
2
= 0
= Initial range value (for process alarm)
= 0 (for deviation alarm)
= 0.0 (for control output alarm)
= 0
= 0
= Initial range value (for process alarm)
= 0 (for deviation alarm)
= 0.0 (for control output alarm)
= 0
= 0
= Initial range value (for process alarm)
= 0 (for deviation alarm)
= 0.0 (for control output alarm)
= 0
= 0
= Initial scale value
= Final scale value
= 1
= 1
= 1
= 1
06/04/2006, 16.15
Run time group 4 [r.dxx]
PARAMETER DEFAULT VALUE
Pb
HYS ti td
IP r.Gn
OLAP
Cn.Ac
Pb 1
HYS 1 ti 1
= 4.0 %
= 0.5 %
= 4.00 mm.ss
= 1.00 mm.ss
= 50.0 (If only one control output is configured).
0.0 (If two control outputs, without split range, are configured).
= 1.00
= 0
= rEV
= 4.0 %
= 0.5 %
= 4.00 mm.ss
td 1
IP 1 r.Gn 1
OLP.1
Pb 2
HYS 2 ti 2 td 2
= 1.00 mm.ss
= 50.0 (If only one control output is configured).
0.0 (If two control outputs, without split range, are configured).
= 1.00
= 0
= 4.0 %
= 0.5 %
= 4.00 mm.ss
= 1.00 mm.ss
A. 3 r.Gn 3
OLP.3
Pb 4
HYS 4 ti 4 td 4
IP 4 r.Gn 4
OLP.4
IP 2 r.Gn 2
OLP.2
Pb 3
HYS 3 ti 3 td 3
IP 3
XKC-A-D2.pmd
3
= 50.0 (If only one control output is configured).
0.0 (If two control outputs, without split range, are configured).
= 1.00
= 0
= 4.0 %
= 0.5 %
= 4.00 mm.ss
= 1.00 mm.ss
= 50.0 (If only one control output is configured).
0.0 (If two control outputs, without split range, are configured).
= 1.00
= 0
= 4.0 %
= 0.5 %
= 4.00 mm.ss
= 1.00 mm.ss
= 50.0 (If only one control output is configured).
0.0 (If two control outputs, without split range, are configured).
= 1.00
= 0
06/04/2006, 16.15
Pb 5
HYS 5 ti 5 td 5
IP 5 r.Gn 5
OLP.5
PARAMETER
ArW
Sñ.tt
Sñ.db
ñ.OLL
ñ.OLH
ñ.rñP
ñC.CY
S.OLL
= 4.0 %
= 0.5 %
= 4.00 mm.ss
= 1.00 mm.ss
= 50.0 (If only one control output is configured).
0.0 (If two control outputs, without split range, are configured).
= 1.00
= 0
DEFAULT VALUE
= 100%
= 1.00 m
= 5%
= 0.0%
= 100.0%
= Inf
= 15 s (If relay output)
2 s (If SSR output)
= 0.0%
A. 4
S.OLH
S.rñP
SC.CY
rL rH
Grd1
Grd2 tOL
E.Añ
E.Lr
E.rd
= 100.0%
= Inf
= 15 s (If relay output)
2 s (If SSR output)
= Initial range value
= Final range value
= Inf
= Inf
= Inf
= On
= On
= On
Run time group 6 [r.Fxx]
PARAMETER DEFAULT VALUE
A1.tP
A1.Cn
A1.Ac
= Proc
= H.A.
= rEV
A1.St
A2.tP
A2.Cn
A2.Ac
A2.St
A3.tP
A3.Cn
= OFF
= Proc
= H.A.
= rEV
= OFF
= Proc
= H.A.
XKC-A-D2.pmd
4 06/04/2006, 16.15
A3.Ac
A3.St
A4.tP
A4.Cn
A4.Ac
A4.St
Fd.Cn
Fd.Ac
= rEV
= OFF
= Proc
= H.A.
= rEV
= OFF
= A.
= rEV
PARAMETER
S.L.Pr
S.L.Ad
S.L.bd
S.L.bF
DEFAULT VALUE
= ñbUS
= 1
= 19.20
= 8
Run time group 8 [r.Hxx]
The default calibration data are the complete potentiometer travel.
AFTER THE DEFAULT DATA LOADING OF THIS GROUP, IT
IS NECESSARY TO PERFORM THE PROPER CALIBRATION
Run time group 9 [r.Ixx]
PARAMETER DEFAULT VALUE t.A.1
t.b.1
t.A.2
= 500
= 500
= 500 t.b.2
t.A.3
t.b.3
t.A.4
t.b.4
t.A.5
t.b.5
t.A.6
t.b.6
t.A.7
= 500
= 500
= 500
= 500
= 500
= 500
= 500
= 500
= 500
= 500 t.b.7
t.A.8
t.b.8
t.A.9
t.b.9
t.A.10
t.b.10
= 500
= 500
= 500
= 500
= 500
= 500
= 500
A. 5
XKC-A-D2.pmd
5 06/04/2006, 16.15
Pb.Lo
Pb.Hi
ti.Lo
ti.Hi
rG.CL
Run time group Hd [r.Lxx]
PARAMETER DEFAULT VALUE
= 1.0%
= 300.0%
= 00.20 mm.ss
= 20.00 mm.ss
= OFF
XKC-A-D2.pmd
6
DEFAULT CONFIGURATION AND USER PARAMETERS
When it is desired to load the default value of:
- the standard configuration parameters;
- the user setting of the run time and configuation parameters; proceed as follows: a) If the instrument starts in configuration mode, push the MENU pushbutton.
b) If the instrument starts in run time mode, by keeping depressed the MENU push-button for more than 5 seconds the instrument will show: s according to "CnF.6" "t.out" [time out selection" C.I10] parameter setting), the instrument returns automatically to the normal display mode.
By V or W push-button select "ñodF."
A. 6
1) When modify mode is started, the instrument stops the control and:
- sets control outputs to OFF;
06/04/2006, 16.15
- turned OFF the bargraph displays (MKC only);
- sets analog retransmissions to the retransmitted initial scale value;
- sets alarms in no alarm condition;
- sets events to OFF;
- disables the serial link;
- the time out will be removed.
2) When the modify mode is disabled by V101 (SW3), the V or W push-button pressure has no effect.
Push MENU pushbutton again and select the:
Default configuration and user parameter setting group [C.Cxx]
Upper display: ConF
Ranges: tb.1 =load the default configuration parameters of the table 1 (European) tb.2 =load the default configuration parameters of the table 2 (American)
LOAd =load the user setting (all run time and configuration parameters)
SAVE=save the current setting of the run time and configuration parameters (as user default setting)
Lower display: dFlt
USEr when "Tb.1" or "Tb.2" is selected when "LOAd" or "SAVE" is selected
Push MENU pushbutton again.
A. 7
The central display will show: and then the display will show:
The default parameter loading procedure is ended.
The following is a list of the default configuration parameters of tb
1 and tb 2:
PARAM.
Ln.Fr
ñ.In.t
ñ.In.d
ñ.In.S
ñ.In.L
ñ.In.H
OFSt dS.FL
Configuration group 1 [C.dxx]
VALUE NOTES
50
3
Hz
TC K with °C
----.
(No decimal figure) dIS
- 100
1370
0
0
Disabled
°C
°C
°C
(No filter)
XKC-A-D2.pmd
7 06/04/2006, 16.15
A.In.F
A.In.t
A.In.L
A.In.H
A.I.FL
PARAM.
O1.Fn
O2.Fn
O3.Fn
O4.Fn
Sñ.tP
FEEd
O5.Fn
O5.rn
O5.Lr
nonE
4-20
0
1000
0
VALUE
ñAin
ALr.1
ALr.2
nonE
ñC.Sñ
ALr.3
nonE
ALr.4
CLSd
OPEn no.Fb
nonE
ñAin
4-20
0 mA
°C
°C
(No filter)
O5.Hr
O5.FL
O6.Fn
O6.rn
O6.Lr
O6.Hr
O6.FL
1000
0 nonE
SP.rt
4-20
0
1000
0
°C
No filter
If option is not mounted
If option is mounted
4-20 mA
°C
°C
(No filter)
NOTES
If servo motor drive is not mounted
If servo motor drive or linear output is mounted
If option is not mounted
If servo motor drive is mounted
If option is mounted
If option is not mounted
If option is mounted
If feedback circuitry is mounted
If feedback circuitry is not mounted
If option is not mounted
If option is mounted
4-20 mA
°C
A. 8
PARAM.
SPLt.
ñC.Gn
ñC.bS
SC.Gn
SC.bS
ñC.Cn
ñ.SCL
ñC.dP
ñC.E.L
ñC.E.H
C.A.C
SC.Cn
S.SCL
Configuration group 3 [C.Fxx]
VALUE NOTES dIS
2.00
-50.0
2.00
0.0
norñ nO
----.
0
100 bEFr norñ nO
(No decimal figure)
XKC-A-D2.pmd
8 06/04/2006, 16.15
SC.dP
SC.E.L
SC.E.H
SC.A.C
PARAM.
Sñ.Fn
Cn.tP
ñAn.F
Añ.UL
ñ.A.t.t
St.Fn
St.Pr
St.tk
SF.Cn
SF.UL
PARAM.
d1.Fn
d1.St
d2.Fn
d2.St
d3.Fn
----.
0
100 bEFr
(No decimal figure)
VALUE
Enb
PId
Enb buñ.
buñ.
Cnd.b
Edit
0
Std.
0.0
NOTES
VALUE nonE
OPEn nonE
OPEn nonE
NOTES
XKC-A-D2.pmd
9
A. 9
I4.Fn
I4.St
I5.Fn
I5.St
I6.Fn
I6.St
I7.Fn
I7.St
I8.Fn
I8.St
d3.St
I1.Fn
I1.St
I2.Fn
I2.St
I3.Fn
I3.St
F.E.01
S.E.01
F.E.02
S.E.02
F.E.03
S.E.03
F.E.04
S.E.04
nonE
OPEn nonE
OPEn nonE
OPEn nonE
OPEn nonE
OPEn
OPEn nonE
OPEn nonE
OPEn nonE
OPEn
Brk.E
OPEn
Brk.E
OPEn
Brk.E
OPEn
Brk.E
OPEn
06/04/2006, 16.15
F.E.10
S.E.10
F.E.11
S.E.11
F.E.12
S.E.12
F.E.13
S.E.13
F.E.14
S.E.14
F.E.15
S.E.15
F.E.16
S.E.16
F.E.17
S.E.17
F.E.18
S.E.18
F.E.19
S.E.19
t.E.CY
t.E.Pr
OPEn nonE
OPEn nonE
OPEn nonE
OPEn nonE
OPEn nonE nonE
OPEn nonE
OPEn nonE
OPEn nonE
OPEn nonE
OPEn
30
30
XKC-A-D2.pmd
10
A. 10
PARAM.
G.brG
O.brG
brG.L
brG.H
brG.d
SP.AL
SP.dS
Sr.bH
SS.tr
t.out
Fd.Fn
Fd.HS
Fd.Ou
Configuration group 6 [C.Ixx]
VALUE NOTES
DEv
P.Out
-100
1370
10
°C
°C
°C n.ALG
OP.SP
bAL
-100 tñ.10
nonE
ñC.On
25 nonE
°C
If option is not mounted or main control output is linear
If option is mounted
06/04/2006, 16.15
O2.Fn
O3.Fn
PARAM.
Ln.Fr
ñ.In.t
ñ.In.d
ñ.In.S
ñ.In.L
ñ.In.H
OFSt dS.FL
A.In.F
A.In.t
A.In.L
A.In.H
A.I.FL
Configuration group 1 [C.dxx]
VALUE NOTES
60
18
Hz
(TC K with °F)
----.
dIS
(No decimal figure)
-150
2500
0
0 nonE
4-20
32
1832
0
Disabled
°F
°F
°F
(No filter) mA
°F
°F
(No filter)
PARAM.
O1.Fn
VALUE
ñAin
ALr.1
O4.Fn
Sñ.tP
FEEd
O5.Fn
O5.rn
O5.Lr
O5.Hr
O5.FL
O6.Fn
NOTES
If servo motor drive is not mounted
If servo motor drive or linear output is mounted
A. 11
O6.rn
O6.Lr
O6.Hr
O6.FL
XKC-A-D2.pmd
11
ALr.2
nonE
ñC.Sñ
4-20
32
1832
0 nonE
SP.rt
4-20
32
1832
0
ALr.3
nonE
Alr.4
CLSd
OPEn no.Fb
nonE
ñAin
If option is not mounted
If servo control motor drive is mounted
If option is mounted
If option is not mounted
If option is mounted
If feedback circuitry is mounted
If feedback circuitry is not mounted
If option is not mounted
If option is mounted
4-20 mA
°F
°F
No filter
If option is not mounted
If option is mounted
4-20 mA
°F
°F
(No filter)
06/04/2006, 16.15
PARAM.
SPLt.
ñC.Gn
ñC.bS
SC.Gn
SC.bS
ñC.Cn
ñ.SCL
ñC.dP
ñC.E.L
ñC.E.H
ñC.A.C
SC.Cn
S.SCL
SC.dP
SC.E.L
SC.E.H
SC.A.C
Configuration group 3 [C.Fxx]
VALUE NOTES dIS
2.00
-50.0
2.00
0.0
norñ nO
----.
(No decimal figure)
0
100 bEFr norñ nO
----.
0
100 bEFr
(No decimal figure)
XKC-A-D2.pmd
12
PARAM.
Sñ.Fn
Cn.tP
ñAn.F
Añ.UL
ñ.A.t.t
St.Fn
St.Pr
St.tk
SF.Cn
SF.UL
Configuration group 4 [C.Gxx]
VALUE NOTES
Enb
PId
Enb buñ.
buñ.
Cnd.b
Edit
0
Std.
0.0
A. 12
PARAM.
d1.Fn
d1.St
d2.Fn
d2.St
d3.Fn
d3.St
I1.Fn
I1.St
VALUE nonE
OPEn nonE
OPEn nonE
OPEn nonE
OPEn
NOTES
06/04/2006, 16.15
I2.Fn
I2.St
I3.Fn
I3.St
I4.Fn
I4.St
I5.Fn
I5.St
I6.Fn
I6.St
I7.Fn
I7.St
I8.Fn
I8.St
F.E.01
S.E.01
F.E.02
S.E.02
F.E.03
S.E.03
F.E.04
S.E.04
F.E.10
S.E.10
F.E.11
OPEn nonE
OPEn nonE
OPEn nonE
OPEn
Brk.E
OPEn
Brk.E
nonE
OPEn nonE
OPEn nonE
OPEn nonE
OPEn
Brk.E
OPEn
Brk.E
OPEn nonE
OPEn nonE
XKC-A-D2.pmd
13
A. 13
S.E.11
F.E.12
S.E.12
F.E.13
S.E.13
F.E.14
S.E.14
F.E.15
S.E.15
F.E.16
S.E.16
F.E.17
S.E.17
F.E.18
S.E.18
F.E.19
S.E.19
t.E.CY
t.E.Pr
nonE
OPEn nonE
OPEn nonE
OPEn nonE
OPEn nonE
OPEn
30
30
OPEn nonE
OPEn nonE
OPEn nonE
OPEn
06/04/2006, 16.15
PARAM.
G.brG
O.brG
brG.L
brG.H
brG.d
SP.AL
SP.dS
Sr.bH
SS.tr
t.out
Fd.Fn
Fd.HS
Fd.Ou
En.Ck
HYtñ
Configuration group 6 [C.Ixx]
VALUE NOTES
DEv
P.Out
-150
2500
10
°F
°F
°F n.ALG
OP.SP
bAL
-150 tñ.10
nonE
°F
If option is not mounted or main control output is linear
If option is mounted ñC.On
25 nonE nonE
0.01 h.mm
A. 14
XKC-A-D2.pmd
14 06/04/2006, 16.15
MODEL: MKP = 1/4 DIN
PKP = 1/8 DIN
INPUT: : : : : 1 = Main + Aux-in + Logic Inputs
6 = Main + Aux-in + Logic Inputs +OFD (or Feedback selectable)
OUT1 and OUT2: 11 = Two relay outputs
44 = Two TRIAC outputs
61 = One SSR + one relay output
66 = Two SSR outputs
OUT3 and OUT4:1 = Two relay outputs
2 = Two relay outputs interlockable by jumper (for servomotor output)
OUT5 and OUT6:0 = Not provided
5 = Two mA outputs
7 = One mA output (Out 5)
OPTIONS: 0 = Not provided
1 = Aux. PWS
2 = RS485 + Aux. PWS
4 = Clock calendar + RS485 + Aux. PWS
* For MKP only
5 = Clock calendar + Aux. PWS
6*= RS485 + Aux. PWS + 4 Log. in + 5 Digital out.
7*= RS485 + Aux. PWS + 8 Log. in + 10 Digital out.
8*= Clock calendar + RS485 + Aux. PWS + 4 Log. in + 5 Digital out.
9*= Clock calendar + RS485 + Aux. PWS + 8 Log. in + 10 Digital out.
POWER SUPPL YY
5 = 24V AC/DC
0 0
A. 15
XKC-A-D2.pmd
15 06/04/2006, 16.15
XKC-A-D2.pmd
16 06/04/2006, 16.15
Division of Eurotherm S.r.l
via E. Mattei, 21
28100 Novara
Italy
Tel. +39 0321 481111
Fax. +39 0321 481112
E-mail [email protected]
Http://www.eroelectronic.com
XKC-A-D2.pmd
17 06/04/2006, 16.15
