ENGLISH CAISSON DE GRAVE CS-AW7020 CS-AW7220 CS-AW7040 CS-AW7240 CS-AW7020 CS-AW7040 CS-AW7220 CS-AW7240 For Customer Use: Enter below the Model No, and Serial No, which is located either on the rear or bottom of the speaker unit. Retain this information for future reference. Model No. INSTRUCTION MANUAL MANUEL D'INSTRUCTIONS MANUAL DE INSTRUCCIONES https://manual-hub.com/ Serial No. LVT1743-001A ESPAŃOL FRANÇAIS SUBWOOFER ENGLISH Thank you for purchasing the ARSENAL Car Stereo Speaker. These Speakers can be mounted in the trunk of your vehicle. For the secure installation and perfect operation of your speakers, please read the following carefully. Parts 2. Screw x 10 3. Jump 4. Fuse (10A) x 2 5. Hexagon socket screw keys 1. Grille For proper installation and use 1.Before connecting the speakers to the amplifier, confirm that the power has been turned off. The click noise generated by the connection if the power is on may damage the speakers. 2.The amplifier and speakers should be connected between corresponding terminals, i.e. left to left, and right to right, as well as "+" to "+", and "–" to "–". Connection with reversed polarity will degrade the quality of stereo reproduction. 3.Do not subject the speakers to excessive input. The power handling capacity of the CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 is 600 watts (R.M.S. MUSIC POWER). Any excessive input may damage the speakers. 4.The CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 has an impedance of 2Ω ,4Ω,8Ω. Make sure that the output impedance of the amplifier's speaker terminal is rated at 2Ω,4Ω,8Ω. 5.When cleaning the speakers, use a soft cloth and wipe the surface gently. Do not apply thinner or solvent. 6.Be sure to carefully follow the instructions for: Cable Connections Fuse Replacement Switching the Impedance Selector Subwoofer Mounting and Smart Trim Ring Installation Consult Page 19 of this Instruction Manual for details on these procedures. -2https://manual-hub.com/ Dual 4 Ω Application Diagrams SERIES JUMPER 1 Mono Amplifier 1 Subwoofer Jumper set to Parallel 8Ω(4Ω+4Ω) Load PARALLEL SERIES Jumper Plug Bi-Amp Mono Input 4Ω Input - - Only + + PARALLEL Jumper Plug Input ENGLISH JUMPER 1 Mono Amplifier 1 Subwoofer Jumper set to Series 8Ω(4Ω+4Ω) Load Bi-Amp Mono 4Ω 8Ω Input - - Only + + 4Ω 4Ω 2Ω *JUMPER is Removed 1 2ch Amplifier 1 Subwoofer Jumper is Removed 4Ω Load SERIES Input Stereo + Bi-Amp Configuration 2 Mono Amplifiers 1 Subwoofer Jumper is Removed 4Ω Load *JUMPER is Removed PARALLEL Bi-Amp - Only + SERIES Mono Input - Input Bi-Amp Input - - Only + + 4Ω PARALLEL Mono 4Ω 2-Chan 4Ω JUMPER 1 Mono Amplifier 2 Subwoofers Jumper set to Series Subwoofers wired in Parallel 4Ω Load SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono Input - - Only + + 4Ω 8Ω PARALLEL Jumper Plug Input Bi-Amp 4Ω Input - - Only + + 4Ω 8Ω 4Ω 4Ω JUMPER 1 Mono Amplifier 3 Subwoofers Jumper set to Series Subwoofers wired in Parallel 2.6Ω Load SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 4Ω 8Ω PARALLEL SERIES Jumper Plug Input - - Only + + JUMPER Input Bi-Amp 4Ω 4Ω Input - - Only + + 8Ω PARALLEL Jumper Plug Input Bi-Amp 4Ω Input - - Only + + 4Ω 8Ω 4Ω 2.6Ω JUMPER 1 Mono Amplifier 4 Subwoofers Jumper set to Series Subwoofers wired in Parallel 2Ω Load SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 4Ω 8Ω - 4Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp 4Ω 8Ω 2Ω - -3https://manual-hub.com/ 4Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp Input - - Only + + 4Ω 8Ω 4Ω PARALLEL Jumper Plug Input Bi-Amp - Only + + 4Ω 8Ω Input - 4Ω Dual 2 Ω Application Diagrams SERIES JUMPER 1 Mono Amplifier 1 Subwoofer Jumper set to Parallel 4Ω(2Ω+2Ω) Load PARALLEL SERIES Jumper Plug Input Bi-Amp Mono Input 2Ω Input - - Only + + PARALLEL Jumper Plug ENGLISH JUMPER 1 Mono Amplifier 1 Subwoofer Jumper set to Series 4Ω(2Ω+2Ω) Load Bi-Amp Mono 2Ω 4Ω Input - - Only + + 2Ω 2Ω 1Ω *JUMPER is Removed 1 2ch Amplifier 1 Subwoofer Jumper is Removed 2Ω Load SERIES Input Stereo + Bi-Amp Configuration 2 Mono Amplifiers 1 Subwoofer Jumper is Removed 2Ω Load *JUMPER is Removed PARALLEL Bi-Amp - Only + SERIES Mono Input - Input Bi-Amp Input - - Only + + 2Ω PARALLEL Mono 2Ω 2-Chan 2Ω JUMPER 1 Mono Amplifier 2 Subwoofers Jumper set to Series Subwoofers wired in Parallel 2Ω Load SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono Input - - Only + + 2Ω 4Ω PARALLEL Jumper Plug Input Bi-Amp 2Ω Input - - Only + + 2Ω 4Ω 2Ω 2Ω JUMPER 1 Mono Amplifier 3 Subwoofers Jumper set to Series Subwoofers wired in Parallel 1.3Ω Load SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 2Ω 4Ω PARALLEL SERIES Jumper Plug Input - - Only + + JUMPER Input Bi-Amp 2Ω 2Ω Input - - Only + + 4Ω PARALLEL Jumper Plug Input Bi-Amp 2Ω Input - - Only + + 2Ω 4Ω 2Ω 1.3Ω JUMPER 1 Mono Amplifier 4 Subwoofers Jumper set to Series Subwoofers wired in Parallel 1Ω Load SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 2Ω 4Ω - 2Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp 2Ω 4Ω 1Ω - -4https://manual-hub.com/ 2Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp Input - - Only + + 2Ω 4Ω 2Ω PARALLEL Jumper Plug Input Bi-Amp - Only + + 2Ω 4Ω Input - 2Ω When the speaker cannot be attached in the car, make the sealed enclosure as recommended in the table below—20 mm (3/4 inch) MDF is also recommended for the enclosure materials. CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240 A 15-13/32 inch (391.7 mm) 16-13/32 inch (417.1 mm) B 15-13/32 inch (391.7 mm) 16-13/32 inch (417.1 mm) C 11-13/32 inch (290.1 mm) 13-29/32 inch (353.6 mm) D 9-4/32 inch (232 mm) 10-14/32 inch (275.9 mm) E 9-23/32 inch (247 mm) 11-10/32 inch (295 mm) F 4/32 inch (3 mm) 4/32 inch (3 mm) 3 3 G 1.57 ft (0.045 m ) 2.17 ft3 (0.062 m3) Front & Rear Baffle Boards (x 2) C B Top & Bottom Sides (x 2) G : Internal Volume A Left & Right Sides (x 2) Mounting Hole Dimension * Screw: Dia. 4mm x 50mm (x 8) (supplied) To install the ported enclosure When the speaker cannot be attached in the car, make the sealed enclosure as recommended in the table below—20 mm (3/4 inch) MDF is also recommended for the enclosure materials. CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240 A 15-13/32 inch (391.7 mm) 15-13/32 inch (391.7 mm) B 18-13/32 inch (467.9 mm) 18-13/32 inch (467.9 mm) C 13-13/32 inch (340.9 mm) 15-13/32 inch (391.7 mm) D 9-23/32 inch (247 mm) 10-14/32 inch (275.9 mm) E 9-23/32 inch (247 mm) 11-10/32 inch (295 mm) F 4/32 inch (3 mm) 4/32 inch (3 mm) G 1 inch (25.4 mm) 1 inch (25.4 mm) H 13 inch (330.2 mm) 14 inch (355.6 mm) I 13-19/32 inch (345.4 mm) 13-6/32 inch (335.3 mm) Front & Rear Baffle Boards (x 2) J 1.85 ft3 (0.052 m3) 2.54 ft3 (0.072 m3) C B Top & Bottom Sides (x 2) J : Internal Volume A Left & Right Sides (x 2) G I * Screw: Dia. 4mm x 50mm (x 8) (supplied) H - 5https://manual-hub.com/ Mounting Hole Dimension ENGLISH To install the sealed enclosure Nominal Impedance (Ω) SPL (dB,1W/1M) Displacement (Liter) Hole Cutout Diameter (inch) (mm) Mounting Depth (inch) (mm) CS-AW7020 CS-AW7040 NOTES parallel series parallel series 2Ω + 2Ω 4Ω + 4Ω 83.49 dB 83.54 dB 84.02 dB 84.12 dB SPL : Sound pressure level 0.123 ft3 Dia. 9 - 6/32 inch ( 233 mm ) 6 - 14/32 inch ( 163.5 mm ) Re (Ω) 0.98 Ω 3.83 Ω 1.92 Ω 7.6 Ω Re : DC voice coil resistance BL (T.M) 6.85 13.75 8.68 17.21 BL : Product of Flux density and Effective Voicecoil-wire length Vas (Liter) 17.08 L 16.98 L 18.08 L 18.28 L Vas : Volume of air equal to the driver compliance Vas (CuFt) Me (g) D (mm) 0.6 ft3 0.599 ft3 0.64 ft3 0.65 ft3 145.986 g 147.109 g 124.084 g 122.443 g Me : Effective mass Dia. 202 mm D : Effective cone diameter Fs (Hz) 39.6 Hz 39.5 Hz 41.7 Hz 41.8 Hz Qms 10.261 10.282 9.021 9.169 ENGLISH Parameters Qes 0.756 0.74 0.83 0.824 Qts 0.704 0.691 0.76 0.756 600 W Pe [max.] (W) 14.95 mm Xmax.(mm) Freq.Responce (Hz) Magnet Mass (oz) (g) Voice Coil(Aluminum)Dia.(inch) (mm) Hvc (mm) Hag (mm) 14.8 mm 25 ~500 Hz 65.4 oz ( 1854.1 g ) Dia. 2 - 5/32 inch Dia. 2 - 4/32 inch 54.5 mm 53.59 mm 39.9 mm 39.6 mm 10 mm Fs : Driver free air resonance Qms : Q of driver at Fs considering only non-electrical resistance Qes : Q of driver at Fs considering only electrical resistance Qts : Total Q of driver at Fs Pe[max.] : Maximum continuous input power Xmax. : Maximum effective voicecoil travel without distortion Hvc : Voice coil Height Hag : Gap Height Nominal Impedance (Ω) SPL (dB,1W/1M) Displacement (Liter) Hole Cutout Diameter (inch) (mm) Mounting Depth (inch) (mm) CS-AW7220 CS-AW7240 NOTES parallel series parallel series 2Ω + 2Ω 4Ω + 4Ω 85.13 dB 85.2 dB 85.87 dB 85.65 dB SPL : Sound pressure level 0.18 ft3 Dia. 10 - 29/32 inch ( 277 mm ) 7 - 6/32 inch ( 182.5 mm ) Re (Ω) 0.98 Ω 3.84 Ω 1.94 Ω 7.61 Ω Re : DC voice coil resistance BL (T.M) 6.84 13.72 9.56 19.14 BL : Product of Flux density and Effective Voicecoil-wire length Vas (Liter) 38.7 L 38.76 L 35.23 L 35.05 L Vas : Volume of air equal to the driver compliance Parameters Vas (CuFt) Me (g) D (cm) 1.37 ft3 1.37 ft3 1.24 ft3 1.24 ft3 171.854 g 172.934 g 157.028 g 157.336 g Me : Effective mass Dia. 246 mm D : Effective cone diameter Fs (Hz) 34.6 Hz 34.5 Hz 37.9 Hz 38 Hz Qms 10.277 10.089 8.931 9.014 Qes 0.786 0.765 0.794 0.781 Qts 0.73 0.711 0.73 0.719 600 W Pe [max.] (W) Xmax.(mm) Freq.Responce (Hz) Magnet Mass (oz) (g) Voice Coil(Aluminum)Dia.(inch) (mm) Hvc (mm) Hag (mm) 14.95 mm 14.8 mm 23 ~500 Hz 86.2 oz ( 2443.7 g ) Dia. 2 - 4/32 inch Dia. 2 - 5/32 inch ( 53.59 mm ) ( 54.5 mm ) 39.9 mm 39.6 mm 10 mm -6https://manual-hub.com/ Fs : Driver free air resonance Qms : Q of driver at Fs considering only non-electrical resistance Qes : Q of driver at Fs considering only electrical resistance Qts : Total Q of driver at Fs Pe[max.] : Maximum continuous input power Xmax. : Maximum effective voicecoil travel without distortion Hvc : Voice coil Height Hag : Gap Height Nous vous remercions pour I'achat d'un haut-parleur auto stéréo de ARSENAL dans le coffre de votre véhicule. Pour un montage sûr et un fonctionnement parfait de ce haut-parleur, il est conseillé de lire attentivement ce qui suit. 2. Screw x 10 3. Jump 4. Fuse (10A) x 2 5. Hexagon socket screw keys 1. Grille Montage et utilisation corrects 1.Vérifier que l'alimentation est coupée avant de raccorder les haut-parleurs à l'amplificateur. Les craquements produits par le raccordement lors que l'alimentation est fournie peuvent endomma ger les haut-parleurs. 2.Raccorder les bornes correspondantes de l’amplificateur et les haut-parleurs, c'est-à-dire, gauche à gauche, droit à droite, de même que “+” à “+” et “–” à “–”. Un raccordement effectué en inversant les polarités réduira la qualité de la reproduction sonore stéréo-phonique. 3.Ne pas appliquer un niveau d'entrée excessif aux haut-parleurs. La puissance d'entrée admissible pour les haut-parleurs CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 est de 600 watts (puissance musicale R.M.S.). Tout signal d'entrée excessif risque de les endommager. 4.Les haut-parleurs CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 ont une impédance de 2Ω,4Ω,8Ω. ll faut par conséquent s'assurer que l'impédance de sortie aux bornes de haut-parleur de l'amplificateur soit aussi de 2Ω,4Ω,8Ω. 5.Nettoyer le haut-parleur en le frottant légèrement à l'aide d'un chiffon doux. Ne jamais utiliser de solvants ni de détergents. 6.Veuillez suivre attentivement les instructions suivantes pour: Connections de Câble Remplacement de Fusible Changement de la Sélection d'Impédance Montage du Subwoofer et Installation Pratique de la Moulure de Finition Consultez la Page 19 de ce Manuel d'Instruction pour les détails de cesprocédures. -7https://manual-hub.com/ FRANÇAIS Parts Diagrammes d’application duale 4Ω JUMPER SERIES PARALLEL Jumper Plug Input Bi-Amp Mono 4Ω SERIES Input Input - - Only + + FRANÇAIS JUMPER 1 amplificateur mono 1 (un) caisson de basse Cavalier branché en Parallèle Impédance de charge de 8Ω(4Ω+4Ω) Bi-Amp Mono 8Ω Input - - Only + + 4Ω PARALLEL Jumper Plug 1 amplificateur mono 1 (un) caisson de basse Cavalier branché en Série Impédance de charge de 8Ω(4Ω+4Ω) 4Ω 4Ω 2Ω *JUMPER is Removed 1 amplificateur mono 1 (un) caisson de basse Cavalier branché en Parallèle Impédance de charge de 8Ω(4Ω+4Ω) SERIES Configuration en double amplification 2 amplificateurs mono *JUMPER is Removed 1 (un) caisson de basse Cavalier débranché Impédance de charge de 4Ω PARALLEL SERIES Input Stereo + Bi-Amp - Only + PARALLEL Input - Mono Input 4Ω 2-Chan Bi-Amp Input - - Only + + 4Ω Mono 4Ω JUMPER 1 amplificateur mono 2 (deux) caissons de basse Cavalier branché en Série Subwoofers wired in Parallel Impédance de charge de 4Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono Input - - Only + + 4Ω 8Ω PARALLEL Jumper Plug Input Bi-Amp 4Ω Input - - Only + + 4Ω 8Ω 4Ω 4Ω JUMPER 1 amplificateur mono 3 (trois) caissons de basse Cavalier branché en Série Subwoofers wired in Parallel Impédance de charge de 2.6Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 4Ω 8Ω PARALLEL SERIES Jumper Plug Input - - Only + + JUMPER Input Bi-Amp 4Ω 4Ω Input - - Only + + 8Ω PARALLEL Jumper Plug Input Bi-Amp 4Ω Input - - Only + + 4Ω 8Ω 4Ω 2.6Ω JUMPER 1 amplificateur mono 4 (quatre) caissons de basse Cavalier branché en Série Subwoofers wired in Parallel Impédance de charge de 2Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 4Ω 8Ω - 4Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp 4Ω 8Ω 2Ω - -8https://manual-hub.com/ 4Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp Input - - Only + + 4Ω 8Ω 4Ω PARALLEL Jumper Plug Input Bi-Amp - Only + + 4Ω 8Ω Input - 4Ω Diagrammes d’application duale 2Ω JUMPER PARALLEL Jumper Plug Input Bi-Amp Mono Input 2Ω Input - - Only + + SERIES Bi-Amp Mono 4Ω Input - - Only + + 2Ω PARALLEL 2Ω 2Ω 1Ω *JUMPER is Removed 1 amplificateur mono 1 (un) caisson de basse Cavalier branché en Parallèle Impédance de charge de 4Ω(2Ω+2Ω) SERIES Configuration en double amplification 2 amplificateurs mono *JUMPER is Removed 1 (un) caisson de basse Cavalier débranché Impédance de charge de 2Ω PARALLEL SERIES Input Stereo + Bi-Amp - Only + PARALLEL Input - Mono Input 2Ω 2-Chan Bi-Amp Input - - Only + + 2Ω Mono 2Ω JUMPER 1 amplificateur mono 2 (deux) caissons de basse Cavalier branché en Série Subwoofers wired in Parallel Impédance de charge de 2Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono Input - - Only + + 2Ω 4Ω PARALLEL Jumper Plug Input Bi-Amp 2Ω Input - - Only + + 2Ω 4Ω 2Ω 2Ω JUMPER 1 amplificateur mono 3 (trois) caissons de basse Cavalier branché en Série Subwoofers wired in Parallel Impédance de charge de 1.3Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 2Ω 4Ω PARALLEL SERIES Jumper Plug Input - - Only + + JUMPER Input Bi-Amp 2Ω 2Ω Input - - Only + + 4Ω PARALLEL Jumper Plug Input Bi-Amp 2Ω Input - - Only + + 2Ω 4Ω 2Ω 1.3Ω JUMPER 1 amplificateur mono 4 (quatre) caissons de basse Cavalier branché en Série Subwoofers wired in Parallel Impédance de charge de 1Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 2Ω 4Ω - 2Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp 2Ω 4Ω 1Ω - -9https://manual-hub.com/ 2Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp Input - - Only + + 2Ω 4Ω 2Ω PARALLEL Jumper Plug Input Bi-Amp - Only + + 2Ω 4Ω Input - 2Ω FRANÇAIS SERIES JUMPER 1 amplificateur mono 1 (un) caisson de basse Cavalier branché en Parallèle Impédance de charge de 4Ω(2Ω+2Ω) Jumper Plug 1 amplificateur mono 1 (un) caisson de basse Cavalier branché en Série Impédance de charge de 4Ω(2Ω+2Ω) Pour installer l’enceinte hermétique Si le haut-parleur ne peut pas être fixé directement dans cette voiture, fabriquez une enceinte hermétique de façon recommandéeà l’aide des spécifications données dans le tableau ci-dessous; le CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240 MDF—20 mm (3/4 pouce) est recommandé pour le matériau A 15-13/32 inch (391.7 mm) 16-13/32 inch (417.1 mm) de l’enceinte. B 15-13/32 inch (391.7 mm) 16-13/32 inch (417.1 mm) C 11-13/32 inch (290.1 mm) 13-29/32 inch (353.6 mm) D 9-4/32 inch (232 mm) 10-14/32 inch (275.9 mm) E 9-23/32 inch (247 mm) 11-10/32 inch (295 mm) F 4/32 inch (3 mm) 4/32 inch (3 mm) 3 3 G 1.57 ft (0.045 m ) 2.17 ft3 (0.062 m3) Écrans acoustiques avant et arrière (x 2) C FRANÇAIS B Faces supérieure et inférieure (x 2) G : Volume interne A Faces gauche et droite (x 2) Faces gauche et droite (x 2) * Vis: Dia. 4mm x 50mm (x 8) (fournis) Pour installer l’enceinte hermétique Si le haut-parleur ne peut pas être fixé directement dans cette voiture, fabriquez une enceinte hermétique de façon recommandéeà l’aide des spécifications données dans le tableau ci-dessous; le CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240 MDF—20 mm (3/4 pouce) est recommandé pour le matériau A 15-13/32 inch (391.7 mm) 15-13/32 inch (391.7 mm) de l’enceinte. B 18-13/32 inch (467.9 mm) 18-13/32 inch (467.9 mm) C 13-13/32 inch (340.9 mm) 15-13/32 inch (391.7 mm) D 9-23/32 inch (247 mm) 10-14/32 inch (275.9 mm) E 9-23/32 inch (247 mm) 11-10/32 inch (295 mm) F 4/32 inch (3 mm) 4/32 inch (3 mm) G 1 inch (25.4 mm) 1 inch (25.4 mm) H 13 inch (330.2 mm) 14 inch (355.6 mm) I 13-19/32 inch (345.4 mm) 13-6/32 inch (335.3 mm) Écrans acoustiques avant et arrière (x 2) J 1.85 ft3 (0.052 m3) 2.54 ft3 (0.072 m3) C B Faces supérieure et inférieure (x 2) J : Volume interne A G I * Vis: Dia. 4mm x 50mm (x 8) (fournis) Faces gauche et droite (x 2) H Faces gauche et droite (x 2) - 10 https://manual-hub.com/ CS-AW7020 CS-AW7040 REMARQUES parallel series parallel series Impédance nominale (Ω) 2Ω + 2Ω 4Ω + 4Ω SPL (dB,1W/1M) 83.49 dB 83.54 dB 84.02 dB 84.12 dB SPL : Niveau de pression sonore 0.123 ft3 Déplacement (Liter) Dia. 9 - 6/32 inch Diamètre du tuou de découpe (pouces) ( 233 mm ) (mm) 6 - 14/32 inch Profondeur de montage (pouces) ( 163.5 mm ) (mm) Re : Résistance de la bobine mobile Re (Ω) 0.98 Ω 3.83 Ω 1.92 Ω 7.6 Ω en CC BL : Produit de la densité de flux et de la longueur efficace de fil de la bobine 6.85 13.75 8.68 17.21 BL (T.M) mobile Vas : Volume d'air égal à la conformité Vas (Iitre) 17.08 L 16.98 L 18.08 L 18.28 L de l'excitateur Vas (CuFt) 0.599 ft3 0.64 ft3 0.65 ft3 0.6 ft3 Me (g) 145.986 g 147.109 g 124.084 g 122.443 g Me : Masse effective Dia. 202 mm D (mm) D : Diamètre effectif du cône Fs : Résonance à l'air libre de Fs (Hz) 39.6 Hz 39.5 Hz 41.7 Hz 41.8 Hz l'excitateur Qms 10.261 Qes Qts 10.282 9.021 9.169 0.756 0.74 0.83 0.824 0.704 0.691 0.76 0.756 600 W Pe [max.] (W) Xmax. (mm) Réponse en fréquence (Hz) Masse de l’aimant (once) (g) Diamètre de la bobine mobile (pouces) (mm) Hvc (mm) Hag (mm) 14.95 mm 14.8 mm 25 ~500 Hz 65.4 oz ( 1854.1 g ) Dia. 2 - 5/32 inch Dia. 2 - 4/32 inch ( 54.5 mm ) ( 53.59 mm ) 39.9 mm 39.6 mm 10 mm Qms : Q de l'excitateur à Fs considérant uniquement la résistance non-électrique Qes : Q de l'excitateur à Fs considérant uniquement la résistance électrique Qts : Q total de l'excitateur à Fs Pe[max.] : Puissance d'entrée continue maximum Xmax. : Déplacement effectif maximum de la bobine mobile sans distorsion Hvc : Hauteur de la bobine mobile Hvc : Hauteur de la bobine mobile CS-AW7220 CS-AW7240 Paramètres REMARQUES parallel series parallel series Impédance nominale (Ω) 2Ω + 2Ω 4Ω + 4Ω SPL (dB,1W/1M) 85.2 dB 85.87 dB 85.65 dB SPL : Niveau de pression sonore 85.13 dB 0.18 ft3 Déplacement (Liter) Dia. 10 - 29/32 inch Diamètre du tuou de découpe (pouces) ( 277 mm ) (mm) 7 - 6/32 inch Profondeur de montage (pouces) ( 182.5 mm ) (mm) Re : Résistance de la bobine mobile Re (Ω) 0.98 Ω 3.84 Ω 1.94 Ω 7.61 Ω en CC BL : Produit de la densité de flux et de l a longueur efficace de fil de la bobine 6.84 13.72 9.56 19.14 BL (T.M) mobile Vas : Volume d'air égal à la conformité Vas (Iitre) 38.7 L 38.76 L 35.23 L 35.05 L de l'excitateur Vas (CuFt) 1.37 ft3 1.24 ft3 1.24 ft3 1.37 ft3 Me (g) 171.854 g 172.934 g 157.028 g 157.336 g Me : Masse effective Dia. 246 mm D (mm) D : Diamètre effectif du cône Fs : Résonance à l'air libre de Fs (Hz) 34.6 Hz 34.5 Hz 37.9 Hz 38 Hz l'excitateur Qms 10.277 10.089 8.931 9.014 Qes 0.786 0.765 0.794 0.781 Qts 0.73 0.711 0.73 0.719 600 W Pe [max.] (W) Xmax. (mm) Réponse en fréquence (Hz) Masse de l’aimant (once) (g) Diamètre de la bobine mobile (pouces) (mm) Hvc (mm) Hag (mm) 14.95 mm 14.8 mm 23 ~500 Hz 86.2 oz ( 2443.7 g ) Dia. 2 - 5/32 inch Dia. 2 - 4/32 inch ( 54.5 mm ) ( 53.59 mm ) 39.9 mm 39.6 mm 10 mm - 11 https://manual-hub.com/ Qms : Q de l'excitateur à Fs considérant uniquement la résistance non-électrique Qes : Q de l'excitateur à Fs considérant uniquement la résistance électrique Qts : Q total de l'excitateur à Fs Pe[max.] : Puissance d'entrée continue maximum Xmax. : Déplacement effectif maximum de la bobine mobile sans distorsion Hvc : Hauteur de la bobine mobile Hvc : Hauteur de la bobine mobile FRANÇAIS Paramètres Le agradecemos la adquisición del Altavoz Estereofónico para Automóvil de ARSENAL. Para efectuar una instalación segura y para que el altavoz funcione correctamente, lea detenidamente las siguientes instrucciones. ESPAŃOL Parts 2. Screw x 10 3. Jump 4. Fuse (10A) x 2 5. Hexagon socket screw keys 1. Grille Instalación y uso correctos 1.Antes de conectar los altavoces con el amplificador, confirme que esté cortada la alimentación eléctrica. El ruido producido al realizar la conexión con la alimentación conectada puede causar daños en los altavoces. 2.Deben conectares los terminales correspondientes del amplificador y de los altavoces, es decir izquierdo a izquierdo y derecho a derecho,asi co mo “+” a “+” y “–” a “–”. Si las polaridades se co nectan inversamente, la reproducción este reofónica se deteriorará. 3.No someta los altavoces a una entrada excesiva. La capacidad máxima de los CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 es de 600 votios (POTENCIA MUSICAL R.M.S.). Una entra da excesiva dañará los altavoces. 4.Los CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 tienen 2Ω,4Ω,8Ω de impedancia. Asegúrese de que la impe dancia de salida del terminal para altavoces de amplificador sea de 2Ω, 4Ω,8Ω. 5.Cuando limpie los altavoces, utilice un paño suave y frote la superficie con cuidado. No aplique solventes ni diluyentes. 6.Asegurese de seguir cuidadosamente las instrucciones para: Conecciones de Cable Reemplazo de fucible Cambiando el Selector de Resistencia Instalar el subwoofer y la moldura del anillo Consulte la Page 19 de este Manual de Instrucciones para los detalles de estos procedimientos. - 12 https://manual-hub.com/ Diagramas de Aplicasion Dual 4Ω JUMPER SERIES JUMPER 1 amplificador monofónico 1(un) bajo Puente fijado en Paralelo Carga a 8Ω(4Ω+4Ω) PARALLEL SERIES Jumper Plug Bi-Amp Mono Input 4Ω Input - - Only + + Jumper Plug Input PARALLEL Bi-Amp Mono 4Ω 8Ω Input - - Only + + 4Ω 4Ω 2Ω *JUMPER is Removed Amplificador 1,2 ch 1(un) bajo Se quita el puente Carga a 4Ω SERIES Input Stereo + Configuracion Bi-Amplificada 2 amplificadores monofónicos 1(un) bajo Se quita el puente Carga a 4Ω *JUMPER is Removed PARALLEL Bi-Amp - Only + SERIES Mono Input - Input Bi-Amp Input - - Only + + 4Ω PARALLEL Mono 4Ω 2-Chan 4Ω JUMPER 1 amplificador monofónico 2 (Dos) bajos Puente fijado en serie Subwoofers wired in Parallel Carga a 4Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono Input - - Only + + 4Ω 8Ω PARALLEL Jumper Plug Input Bi-Amp 4Ω Input - - Only + + 4Ω 8Ω 4Ω 4Ω JUMPER 1 amplificador monofónico 3 (Tres) bajos Puente fijado en serie Subwoofers wired in Parallel Carga a 2.6Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 4Ω 8Ω PARALLEL SERIES Jumper Plug Input - - Only + + JUMPER Input Bi-Amp 4Ω 4Ω Input - - Only + + 8Ω PARALLEL Jumper Plug Input Bi-Amp 4Ω Input - - Only + + 4Ω 8Ω 4Ω 2.6Ω JUMPER 1 amplificador monofónico 4 (Cuatro) bajos Puente fijado en serie Subwoofers wired in Parallel Carga a 2Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 4Ω 8Ω - 4Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp 4Ω 8Ω 2Ω - - 13 https://manual-hub.com/ 4Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp Input - - Only + + 4Ω 8Ω 4Ω PARALLEL Jumper Plug Input Bi-Amp - Only + + 4Ω 8Ω Input - 4Ω ESPAŃOL 1 amplificador monofónico 1(un) bajo Puente fijado en serie Carga a 8Ω(4Ω+4Ω) Diagramas de Aplicasion Dual 2Ω JUMPER 1 amplificador monofónico 1(un) bajo Puente fijado en serie Carga a 4Ω(2Ω+2Ω) SERIES JUMPER 1 amplificador monofónico 1(un) bajo Puente fijado en Paralelo Carga a 4Ω(2Ω+2Ω) PARALLEL SERIES Jumper Plug Bi-Amp Mono Input 2Ω Input - - Only + + Jumper Plug Input Bi-Amp Mono 2Ω Input - - Only + + 4Ω 2Ω 2Ω 1Ω *JUMPER is Removed ESPAŃOL PARALLEL Amplificador 1,2 ch 1(un) bajo Se quita el puente Carga a 2Ω SERIES Input Stereo + Configuracion Bi-Amplificada 2 amplificadores monofónicos 1(un) bajo Se quita el puente Carga a 2Ω *JUMPER is Removed PARALLEL Bi-Amp - Only + SERIES Mono Input - Input Bi-Amp Input - - Only + + 2Ω PARALLEL Mono 2Ω 2-Chan 2Ω JUMPER 1 amplificador monofónico 2 (Dos) bajos Puente fijado en serie Subwoofers wired in Parallel Carga a 2Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono Input - - Only + + 2Ω 4Ω PARALLEL Jumper Plug Input Bi-Amp 2Ω Input - - Only + + 2Ω 4Ω 2Ω 2Ω JUMPER 1 amplificador monofónico 3 (Tres) bajos Puente fijado en serie Subwoofers wired in Parallel Carga a 1.3Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 2Ω 4Ω PARALLEL SERIES Jumper Plug Input - - Only + + JUMPER Input Bi-Amp 2Ω 2Ω Input - - Only + + 4Ω PARALLEL Jumper Plug Input Bi-Amp 2Ω Input - - Only + + 2Ω 4Ω 2Ω 1.3Ω JUMPER 1 amplificador monofónico 4 (Cuatro) bajos Puente fijado en serie Subwoofers wired in Parallel Carga a 1Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 2Ω 4Ω - 2Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp 2Ω 4Ω 1Ω - - 14 https://manual-hub.com/ 2Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp Input - - Only + + 2Ω 4Ω 2Ω PARALLEL Jumper Plug Input Bi-Amp - Only + + 2Ω 4Ω Input - 2Ω Para instalar la caja sellada Cuando el altavoz no se pueda instalCuando el altavoz no se pueda instalCuando el altavoz no se pueda instalusar MDF—20 mm (3/4 pulg.) como material para la caja. CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240 A 15-13/32 inch (391.7 mm) 16-13/32 inch (417.1 mm) B 15-13/32 inch (391.7 mm) 16-13/32 inch (417.1 mm) C 11-13/32 inch (290.1 mm) 13-29/32 inch (353.6 mm) D 9-4/32 inch (232 mm) 10-14/32 inch (275.9 mm) E 9-23/32 inch (247 mm) 11-10/32 inch (295 mm) F 4/32 inch (3 mm) 4/32 inch (3 mm) 3 3 G 1.57 ft (0.045 m ) 2.17 ft3 (0.062 m3) Pantallas acústicas delantera y trasera (x 2) B Lados superior e inferior (x 2) G : El Volumen interior A Lados izquierdo y derecho (x 2) Dimensión del orificio de montaje * Tcrnillo: Dia. 4mm x 50mm (x 8) (suministrado) Para instalar la caja sellada Lados superior e inferior (x 2)Cuando el altavoz no se pueda instalar en el automóvil, construya la caja sellada recomendada en la tablade abajo—Asimismo, serecomienda usar CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240 MDF—20 mm(3/4 pulg.) como material para la caja. A 15-13/32 inch (391.7 mm) 15-13/32 inch (391.7 mm) B 18-13/32 inch (467.9 mm) 18-13/32 inch (467.9 mm) C 13-13/32 inch (340.9 mm) 15-13/32 inch (391.7 mm) D 9-23/32 inch (247 mm) 10-14/32 inch (275.9 mm) E 9-23/32 inch (247 mm) 11-10/32 inch (295 mm) F 4/32 inch (3 mm) 4/32 inch (3 mm) G 1 inch (25.4 mm) 1 inch (25.4 mm) H 13 inch (330.2 mm) 14 inch (355.6 mm) I 13-19/32 inch (345.4 mm) 13-6/32 inch (335.3 mm) Pantallas acústicas delantera y trasera (x 2) J 1.85 ft3 (0.052 m3) 2.54 ft3 (0.072 m3) C B Lados superior e inferior (x 2) J : El Volumen interior A G I * Tcrnillo: Dia. 4mm x 50mm (x 8) (suministrado) H - 15 https://manual-hub.com/ Lados izquierdo y derecho (x 2) Dimensión del orificio de montaje ESPAŃOL C CS-AW7020 CS-AW7040 NOTAS parallel series parallel series Impedancia nominal (Ω) 2Ω + 2Ω 4Ω + 4Ω 83.49 dB 83.54 dB 84.02 dB 84.12 dB SPL : Nivel de presión de sonido SPL (dB,1W/1M) 0.123 ft3 Desplazamiento (litro) Dia. 9 - 6/32 inch Diámetro del orificio cortado (pulgada) ( 233 mm ) (mm) 6 - 14/32 inch Profundidad de montaje (pulgada) ( 163.5 mm ) (mm) Re : Resistencia de la bobina móvil de 0.98 Ω 3.83 Ω 1.92 Ω 7.6 Ω Re (Ω) CC BL : Producto de densidad de flujo y longitud efectiva del cable de la 6.85 13.75 8.68 17.21 BL (T.M) bobina móvil Vas: Volumen de aire equivalente en 17.08 L 16.98 L 18.08 L 18.28 L Vas (litro) conformidad con el excitador Vas (pies cúbicos) 0.599 ft3 0.64 ft3 0.65 ft3 0.6 ft3 145.986 g 147.109 g 124.084 g 122.443 g Me : Masa efectiva Me (g) Dia. 202 mm D (mm) D : Diámetro efectivo del cono ESPAŃOL Parámetros Fs (Hz) 39.6 Hz 39.5 Hz 41.7 Hz 41.8 Hz Qms 10.261 10.282 9.021 9.169 Qes 0.756 0.74 0.83 0.824 Qts 0.704 0.691 0.76 0.756 600 W Pe [máx.] (W) Xmax. (mm) Respuesta de frec (Hz) Masa del imán (oz) (g) Diám.de la bobina móvil (pulgada) (mm) Hvc (mm) Hag (mm) 14.95 mm 14.8 mm 25 ~500 Hz 65.4 oz ( 1854.1 g ) Dia. 2 - 5/32 inch Dia. 2 - 4/32 inch ( 54.5 mm ) ( 53.59 mm ) 39.9 mm 39.6 mm 10 mm Fs : Resonancia del aire sin excitador Qms : Q del excitador a Fs considerando sólo la resistencia no eléctrica Qes : Q del excitador a Fs considerando sólo la resistencia eléctrica Qts : Total Q dei excitador a Fs Pe[max.] : Potencia máxima de entrada contínua Xmax. : Máximo desplazamiento efectivo de la bobina móvil sin distorsón Hvc : Altura de bobina móvil Hag : Altura de entrehierro CS-AW7220 CS-AW7240 Parámetros NOTAS parallel series parallel series Impedancia nominal (Ω) 2Ω + 2Ω 4Ω + 4Ω 85.2 dB 85.87 dB 85.65 dB SPL : Nivel de presión de sonido 85.13 dB SPL (dB,1W/1M) 0.18 ft3 Desplazamiento (litro) Dia. 10 - 29/32 inch Diámetro del orificio cortado (pulgada) ( 277 mm ) (mm) 7 - 6/32 inch Profundidad de montaje (pulgada) ( 182.5 mm ) (mm) Re : Resistencia de la bobina móvil de 0.98 Ω 3.84 Ω 1.94 Ω 7.61 Ω Re (Ω) CC BL : Producto de densidad de flujo y longitud efectiva del cable de la 6.84 13.72 9.56 19.14 BL (T.M) bobina móvil Vas: Volumen de aire equivalente en 38.7 L 38.76 L 35.23 L 35.05 L Vas (litro) conformidad con el excitador Vas (pies cúbicos) 1.37 ft3 1.24 ft3 1.24 ft3 1.37 ft3 171.854 g 172.934 g 157.028 g 157.336 g Me : Masa efectiva Me (g) Dia. 246 mm D (mm) D : Diámetro efectivo del cono Fs (Hz) 34.6 Hz 34.5 Hz 37.9 Hz 38 Hz Qms 10.277 10.089 8.931 9.014 Qes 0.786 0.765 0.794 0.781 Qts 0.73 0.711 0.73 0.719 600 W Pe [máx.] (W) Xmax. (mm) Respuesta de frec (Hz) Masa del imán (oz) (g) Diám.de la bobina móvil (pulgada) (mm) Hvc (mm) Hag (mm) 14.95 mm 14.8 mm 23 ~500 Hz 86.2 oz ( 2443.7 g ) Dia. 2 - 5/32 inch Dia. 2 - 4/32 inch ( 54.5 mm ) ( 53.59 mm ) 39.9 mm 39.6 mm 10 mm - 16 https://manual-hub.com/ Fs : Resonancia del aire sin excitador Qms : Q del excitador a Fs considerando sólo la resistencia no eléctrica Qes : Q del excitador a Fs considerando sólo la resistencia eléctrica Qts : Total Q dei excitador a Fs Pe[max.] : Potencia máxima de entrada contínua Xmax. : Máximo desplazamiento efectivo de la bobina móvil sin distorsón Hvc : Altura de bobina móvil Hag : Altura de entrehierro ES OL h inc ] H /32 mm h 7 c .5 n a. 2i Di [ 5 80/3 ] -2 mm 1 1 5 a. [ 29 Di ES OL h nc ] H 2i m 3 h / 7 .5 m inc a. Di [ 5 3/32 m ] 82 9- 7 m a. [ 24 i D Dia. 12-24/32 inch [ 324 mm ] 7-7/32 inch [ 182.5 mm ] 1-9/32 inch [ 32.69 mm ] Dia. 12-12/32 inch [ 314 mm ] 6-14/32 inch [ 163.5 mm ] Dia. 10-26/32 inch [ 275 mm ] 1-9/32 inch [ 32.51 mm ] Dia. 10-14/32 inch [ 265 mm ] Dia. 9-4/32 inch [ 231.96 mm ] Dia. 10-28/32 inch [ 275.94 mm ] CS-AW7020 CS-AW7040 CS-AW7220 CS-AW7240 - 17 https://manual-hub.com/ Multi Mount Smart Trim Ring (Patent Pending) Santoprene Surround Glass Fiber Laminated Hemp Cone Air Vented Aluminum Cast Basket Integlated Dual-Layer Cone construction Hemp-Fiber Drive Cone Woven Tinsel Lead (Patent Pending) Dual Diametric Progressive Spider Rapid Fire Impedance Selector Speaker Terminal ( Patent Pending) Aluminum Voice Coil Former 4 (2+2) Layer Voice Coils Dual Stacked Strontium Magnet Heat Transfer Silicon Heat Transfer Silicon Aero Vent Bottom Plate T3 Chassis (Thermal Transfer Technology) - 18 https://manual-hub.com/ - 19 https://manual-hub.com/ TO OUR VALUED CUSTOMER THANK YOU FOR PURCHASING THIS JVC PRODUCT. WE WANT TO HELP YOU ACHIEVE A PERFECT EXPERIENCE. NEED HELP ON HOW TO HOOK UP? NEED ASSISTANCE ON HOW TO OPERATE? NEED TO LOCATE A JVC SERVICE CENTER? LIKE TO PURCHASE ACCESSORIES? IS HERE TO HELP! TOLL FREE: 1(800)252-5722 http://www.jvc.com Remember to retain your Bill of Sale for Warranty Service. Do not attempt to service the product yourself Caution To prevent electrical shock, do not open the cabinet. There are no user serviceable parts inside. Please refer to qualified service personnel for repairs. EN, FR, SP © 2007 Victor Company of Japan, Limited Printed in China https://manual-hub.com/ ">
公開リンクが更新されました
あなたのチャットの公開リンクが更新されました。