XM-SD22X SERVICE MANUAL US Model Canadian Model AEP Model UK Model E Model Ver. 1.0 2004.12 SPECIFICATIONS AUDIO POWER SPECIFICATIONS (US MODEL) POWER OUTPUT AND TOTAL HARMONIC DISTORTION 200 watts per channel minimum continuous average power into 4 ohms, both channels driven from 20 Hz to 20 kHz with no more than 0.1% total harmonic distortion per Car Audio Ad Hoc Committee standards. Other Specifications Circuit system OTL (output transformerless) circuit Pulse power supply Inputs RCA pin jacks High level input connector Outputs Speaker terminals Through out pin jacks Suitable speaker impedance 2 – 8 Ω (stereo) 4 – 8 Ω (when used as a bridging amplifier) Maximum outputs 400 W × 2 (at 4 Ω) 600 W × 2 (at 2 Ω) 1,200 W (BTL, at 4 Ω) Rated outputs (supply voltage at 14.4 V) 200 W RMS × 2 (20 Hz – 20 kHz, 0.1% THD + N, at 4 Ω) 250 W RMS × 2 (20 Hz – 20 kHz, 0.15% THD + N, at 2 Ω) 500 W RMS (BTL) (20 Hz – 20 kHz, 0.15% THD + N, at 4 Ω) SN Ratio 93 dBA (Reference 1W into 4 Ω) Frequency response 5 Hz – 50 kHz ( +0 –3 dB) Input level adjustment range 0.3 – 6.0 V (RCA pin jacks) 1.2 – 12.0 V (High level input) Low-pass filter 50 – 300 Hz, –12 dB/oct Low boost 0 – 10 dB (40 Hz) Power requirements 12 V DC car battery (negative ground) Power supply voltage 10.5 – 16 V Current drain at rated output : 48 A (at 4 Ω) Remote input : 1 mA Dimensions Approx. 403 × 55 × 277 mm (15 7/8 × 2 1/4 × 11 in.) (w/h/d) not incl. projecting parts and controls Mass Approx. 5 kg (11 lb. 1 oz.) not incl. accessories Supplied accessories Mounting screws (4) High level input cord (1) Protection cap (1) Design and specifications are subject to change without notice. STEREO POWER AMPLIFIER 9-879-367-01 Sony Corporation 2004L04-1 © 2004.12 e Vehicle Company Published by Sony Engineering Corporation 1 XM-SD22X Note for Replacement of FET Change the both channels of FETs at the output stage. If one or both parts in the following combination is broken, the service kit should be ordered. Service kit part No. Q108, 110, 112 X-3383-027-1 Q208, 210, 212 Q109, 111, 113 X-3383-028-1 Q209, 211, 213 TABLE OF CONTENTS 1. GENERAL Location and Function of Controls .......................................... 3 Connections ............................................................................. 4 2. DISASSEMBLY 2-1. 2-2. 2-3. 2-4. Bottom Plate ........................................................................ 7 Main Board Section ............................................................ 8 Main Board ......................................................................... 8 LED Board .......................................................................... 9 3. ELECTRICAL ADJUSTMENT .................................... 10 4. DIAGRAMS 4-1. 4-2. 4-3. 4-4. Block Diagram .................................................................. 11 Schematic Diagram –Main Section (1/2)– ........................ 12 Schematic Diagram –Main Section (2/2)– ........................ 13 Printed Wiring Boards –Main Section– ............................ 14 5. EXPLODED VIEWS 5-1. Heat Sink (Main) Section .................................................. 16 5-2. Main Board Section .......................................................... 17 6. ELECTRICAL PARTS LIST ......................................... 18 Notes on Chip Component Replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY. 2 XM-SD22X SECTION 1 GENERAL Low boost Amplification de basses fréquences dB 10 0 10 40 100 1k Features Caractéristiques • Maximum power output of 400 W per channel (at 4 Ω). • This unit can be used as a bridging amplifier with a maximum output of 1,200 W. • Direct connection can be made with the speaker output of your car audio unit if it is not equipped with a line output (High level input connection). • Built-in variable LPF (Low-pass filter) and low boost circuit. • Dual mode connection possible for a multispeaker system. • Protection circuit. • Pulse power supply * for stable, regulated output power. • Puissancede sortie maximale de 400 W par canal (à 4 Ω). • Cet appareil peut être utilisé comme amplificateur en pont d’une sortie maximale de 1 200 W. • Une connexion directe est possible avec la sortie haut-parleur de votre autoradio si celle-ci n’est pas équipée d’une sortie de ligne (connexion d’entrée haut niveau). • Filtre passe-bas(LPF) intégré et circuit d’amplification de bassesfréquences. • Double mode de connexion possible au moyen d’un système à plusieurs haut-parleurs. • Circuit de protection. • Alimentation électrique par impulsions * pour une puissance de sortie stable, régulée. * Pulse power supply This unit has a built-in power regulator which converts the power supplied by the DC 12 V car battery into high speed pulses using a semiconductor switch. These pulses are stepped up by the built-in pulse transformer and separated into both positive and negative power supplies before being converted into direct current again. This light weight power supply system provides a highly efficient power supply with a low impedance output. Hz Frequency/Fréquence This section is extracted from instruction manual. Cut-off frequency (LPF) Fréquence de coupure (LPF) dB * Alimentation électrique par impulsions Cet appareil est équipé d’un régulateur de puissance intégré qui convertit la puissance fournie par une batterie de voiture de 12 V CC en impulsions ultra-rapides au moyen d’un commutateur à semi-conducteur. Ces impulsions sont amplifiées par le transformateur d’impulsions intégré et séparées en alimentation positive et négative avant d’être reconverties en courant continu. Ce système d’alimentation de faible poids assure une alimentation électrique très efficace pour une sortie d’impédance faible. 10 0 -10 -20 300Hz -30 170Hz -40 50Hz -50 -60 -70 -80 10 100 Frequency/Fréquence 1k Hz Circuit Diagram Schéma du circuit Power AMP Normal Lch Lch LEVEL (BTL.) LOW BOOST LPF BTL Power AMP Inverted Rch LEVEL Rch Location and Function of Controls Emplacement et fonction des commandes 1 PROTECTOR indicator When the PROTECTOR is activated, the indicator lights up in red. When the PROTECTOR is activated refer to the Troubleshooting Guide. 2 LEVEL adjustment control The input level can be adjusted with this control. Turn it in the clockwise direction when the output level of the car audio unit seemslow. 3 LOW BOOST level control Turn this control to boost the frequencies around 40 Hz to a maximum of 10 dB. 4 Cut-off frequency adjustment control Setsthe cut-off frequency (50 – 300 Hz) for the low-pass filter. 5 FILTER selector switch When the switch is in the LPF position, the filter is set to low-pass. 1 Indicateur PROTECTOR Lorsque PROTECTOR est activé, l’indicateur s’allume en rouge. Lorsque PROTECTOR est activé, reportezvous au guide de dépannage. 2 Commande de réglage LEVEL Le niveau d’entrée peut se régler avec cette commande. Tournez cette commande dans le sens des aiguilles d’une montre lorsque le niveau de sortie de l’autoradio semble faible. 3 Commande de niveau LOW BOOST Tournez cette commande pour amplifier les fréquences autour de 40 Hz jusqu’à un maximum de 10 dB. 4 Commandes de réglage de la fréquence de coupure Permet de régler la fréquence de coupure (50 – 300 Hz) pour le filtre passe-bas. 5 Sélecteur FILTER Lorsque le sélecteur est en position LPF, le filtre est réglé sur passe-bas. LOW BOOST LEVEL PROTECTOR LOW BOOST (40Hz) 2 4 5.5 0.5 6 0.3V FILTER 110 60 0 +10dB 50 OFF 170 260 300Hz LPF 3 XM-SD22X Connections Connexions Caution Attention • Before making any connections, disconnect the ground terminal of the car battery to avoid short circuits. • Be sure to use speakers with an adequate power rating. If you use small capacity speakers, they may be damaged. • Do not connect the # terminal of the speaker system to the car chassis, and do not connect the # terminal of the right speaker with that of the left speaker. • Install the input and output cords away from the power supply wire as running them close together can generate some interference noise. • This unit is a high powered amplifier. Therefore, it may not perform to its full potential if used with the speaker cords supplied with the car. • If your car is equipped with a computer system for navigation or some other purpose, do not remove the ground wire from the car battery. If you disconnect the wire, the computer memory may be erased. To avoid short circuits when making connections, disconnect the +12 V power supply wire until all the other wires have been connected. • Avant d’effectuer les connexions, débranchez la borne de massede la batterie de voiture pour éviter tout court-circuit. • Veillez à utiliser des haut-parleurs de puissance adéquate. Si vous utilisez des hautparleurs de faible capacité, ils risquent d’être endommagés. • Ne raccordez pas la borne # du système de haut-parleurs à la carrosserie de la voiture ni la borne # du haut-parleur droit avec celle du haut-parleur gauche. • Eloignez les câbles d’entrée et de sortie du câble d’alimentation pour éviter les interférences. • Cet appareil est un amplificateur de haute puissance. Il ne peut donc déployer sa pleine puissance que si les câbles de haut-parleurs de la voiture lui sont raccordés. • Si votre voiture est équipée d’un système de navigation ou d’un ordinateur de bord, ne retirez pas le fil de terre de la batterie de la voiture, sinon les données mémorisées seront effacées.Pour éviter un court-circuit lorsque vous effectuez les branchements, branchez le câble d’alimentation +12 V après avoir branché tous les autres fils. 2-Speaker System Système à 2 haut-parleurs +12V LINE OUT Pour plus de détails sur les réglages des commutateurs et commandes, reportezvous à « Emplacement et fonction des commandes ». Left speaker (min. 2 Ω) Right speaker (min. 2 Ω) Haut-parleur gauche (min. 2 Ω) Haut-parleur droit (min. 2 Ω) As a Monaural Amplifier Comme amplificateur monaural Car audio unit Autoradio LINE OUT Make the terminal connections as illustrated below. Procédez aux connexions des bornes comme illustré ci-dessous. REM For details on the settings of switches and controls, refer to “Location and Function of Controls.” Car audio unit Autoradio Right channel Canal droit Left channel Canal gauche 3 GND REM 3 +12V GND BTL BTL BTL BTL c Left speaker (min. 4 Ω) Haut-parleur gauche (min. 4 Ω) Pass the wires through the cap, connect the wires, then cover the terminals with the cap. Faites passer les fils par le cache, raccordez les fils, puis recouvrez les bornes avec le cache. Note When you tighten the screw, be careful not to apply too much torque * as doing so may damage the screw. * The torque value should be less than 1 N•m. Remarque Lorsque vous vissez la vis, faites attention à ne pas appliquer une trop grande force *, car cela pourrait l’endommager. * Le couple de torsion doit être inférieur à 1 N•m. For details on the settings of switches and controls, refer to “Location and Function of Controls.” Pour plus de détails sur les réglages des commutateurs et commandes, reportez-vous à « Emplacement et fonction des commandes ». Note Make sure that the line output from the car audio unit is connected to the jack marked “L (BTL)” on the unit. Remarque Vérifiez que la sortie de ligne de l’autoradio est raccordée à la prise portant l’indication « L (BTL) » sur l’appareil. As the Monaural Amplifier for a Subwoofer Comme amplificateur monaural pour un haut-parleur d’extrêmes graves Power Connection Wires Câbles d’alimentation Car audio unit Autoradio to a metal point of the car Remote output *1 Sortie de commande *1 (REM OUT) Car audio unit Autoradio OFF LPF less than 450 mm (18 in) moins de 450 mm (18 po) *2 Fuse (80 A) Fusible (80 A) BTL *1 If you have the factory original or some other car audio unit without a remote output for the amplifier, connect the remote input terminal (REMOTE) to the accessory power supply. *1 Si vous disposez du modèle d’origine ou d’un autre autoradio sans aucune sortie de commande à distance pour l’amplificateur, raccordez la borne d’entrée de la commande à distance (REMOTE) à la prise d’alimentation accessoires. 4 LINE OUT vers une partie métallique de la carrosserie +12 V car battery Batterie de voiture +12 V Notes on the power supply • Connect the +12 V power supply wire only after all the other wires have been connected. • Be sure to connect the ground wire of the unit securely to a metal point of the car. A loose connection may cause a malfunction of the amplifier. • Be sure to connect the remote control wire of the car audio unit to the remote terminal. • When using a car audio unit without a remote output on the amplifier, connect the remote input terminal (REMOTE) to the accessorypower supply. • Use the power supply wire with a fuse attached (80 A). • All power wires connected to the positive battery post should be fused within 450 mm (18 in) of the battery post, and before they pass through any metal. • Make sure that the vehicle’s battery wires connected to the vehicle (ground to chassis) *2 are of a wire gauge at least equal to that of the main power wire connected from the battery to the amplifier. • Make sure that the wires to be connected to the +12 V and GND terminals of this unit are at least 4-Gauge (AWG-4) or have a sectional area of more than 22.0 mm 2 ( 7/8 in 2). Right speaker (min. 4 Ω) Haut-parleur droit (min. 4 Ω) Remarques sur l’alimentation électrique • Raccordez le câble d’alimentation +12 V uniquement après avoir réalisé toutes les autres connexions. • Raccordezcorrectement le fil de masse à une partie métallique de la voiture. Une connexion lâche peut provoquer un dysfonctionnement de l’amplificateur. • Veillez à raccordez le fil de commande à distance de l’autoradio à la borne de commande à distance. • Si vous utilisez un autoradio dont l’amplificateur ne comporte pas de sortie de commande à distance, raccordez la borne d’entrée de la commande à distance (REMOTE) à la prise d’alimentation accessoires. • Utilisez un câble d’alimentation muni d’un fusible (80 A). • Tous les fils électriques raccordés au support de batterie positif doivent être protégés par un fusible à une distance maximum de 450 mm (18 po) du support de batterie et avant de passer dans une partie métallique quelconque. • Assurez-vous que les fils de la batterie du véhicule raccordés à ce dernier (sol au châssis) *2 sont d’un calibre au moins égal à celui du fil électrique principal reliant la batterie et l’amplificateur. • Assurez-vous que les câbles à raccorder aux bornes +12V et GND de cet appareil sont d’un calibre d’au moins 4 (AWG-4) ou d’une section supérieure à 22,0 mm 2 ( 7/8 po 2). BTL Subwoofer (min. 4 Ω) Haut-parleur d’extrêmes graves (min. 4 Ω) For details on the settings of switches and controls, refer to “Location and Function of Controls.” Pour plus de détails sur les réglages des commutateurs et commandes, reportez-vous à « Emplacement et fonction des commandes ». Note If you wish to use a subwoofer as a monaural speaker, connect the speaker as illustrated above. The output signals to the subwoofer will be the combination of the both right and left output signals. Remarque Si vous désirez utiliser un haut-parleur d’extrêmes graves comme haut-parleur monaural, raccordez le haut-parleur comme illustré ci-dessus. Les signaux de sortie vers le haut-parleur d’extrêmes graves seront une combinaison des signaux de sortie droit et gauche. XM-SD22X Dual Mode System (With a Bridged Subwoofer) Double mode de connexion (avec un haut-parleur d’extrêmes graves en pont) 2-way System Système 2 voies Two output channels Deux canaux de sortie OFF LPF LINE OUT Car audio unit Autoradio Car audio unit Autoradio LINE OUT C1 INPUT THROUGH OUT C2 INPUT Left speaker Haut-parleur gauche OFF LPF Right speaker Haut-parleur droit L Subwoofer Haut-parleur d’extrêmes graves LPF OFF Full range speakers (min. 2 Ω) Haut-parleurs à gamme étendue (min. 2 Ω) Subwoofers (min. 2 Ω) Haut-parleurs d’extrêmes graves (min. 2 Ω) Crossover Frequency unit: Hz When you connect amplifiers using the THROUGH OUT pin jacks, it allows you to connect up to a maximum of three. Otherwise the necessary output levels can not be obtained, and your car audio unit may be damaged. Lorsque vous raccordez des amplificateurs à l’aide des prises à broches THROUGH OUT, vous pouvez raccorder jusqu’à trois amplificateurs. Sinon les niveaux de sortie requis ne peuvent pas être obtenus et votre auto-radio risque d’être endommagé. Use the THROUGH OUT terminal when you install more amplifiers. Audio signals pass through the THROUGH OUT pin jacks unaffected by any signal processing. Utilisez la borne THROUGH OUT lorsque vous installez plusieurs amplificateurs. Les signaux audio transitent par les prises à broches THROUGH OUT sans subir aucun traitement. Tableau des valeurs de recoupement pour 6 dB/octave (4 Ω) Table of crossover values for 6 dB/octave (4 Ω) L (coil) * unit: mH C1/C2 (capacitor)* unit: µF 50 12.7 800 80 8.2 500 100 6.2 130 150 Fréquence de recoupement unité : Hz L (bobine)* unité : mH C1/C2 (condensateur)* unité : µF 50 12,7 800 80 8,2 500 400 100 6,2 400 4.7 300 130 4,7 300 4.2 270 150 4,2 270 200 3.3 200 200 3,3 200 260 2.4 150 260 2,4 150 400 1.6 100 400 1,6 100 600 1.0 68 600 1,0 68 800 0.8 50 800 0,8 50 1000 0.6 39 1000 0,6 39 * (non fournis) * (not supplied) Four output channels Quatre canaux de sortie Car audio unit Autoradio LINE OUT OFF LPF OFF Remarques • Lorsque vous utilisez des circuits de recoupement de fréquence passifs dans un système à plusieurs haut-parleurs, assurez-vous que l’impédance du système n’est pas inférieure à celle prévue pour cet appareil. • Lorsque vous installez un système à 12 décibels/octave dans votre voiture, vous devez respecter les points suivants. Dans un système à 12 décibels/octave où la bobine d’arrêt et le condensateur sont utilisés en série pour former un circuit, vous devez réaliser les branchements avec beaucoup de précaution. Dans ce type de circuit, une augmentation du courant contournant le haut-parleur se produit dans les fréquences se situant autour de la fréquence de coupure. Si des signaux audio continuent d’être fournis dans la zone de la fréquence de recoupement, une surchauffe risque de se produire dans l’amplificateur et le fusible risque de griller. Si le haut-parleur n’est pas raccordé, un circuit de résonance série sera créé par la bobine et le condensateur. Dans ce cas, l’impédance dans la zone de résonance sera considérablement réduite, et comme dans le cas d’un courtcircuit, l’amplificateur peut être endommagé. Par conséquent, veillez à ce qu’un haut-parleur soit toujours raccordé au circuit. LPF Full range speakers (min. 2 Ω) Haut-parleurs à gamme étendue (min. 2 Ω) Notes • When using passive crossover networks in a multispeaker system, care must be taken as the speaker system’s impedance should not be lower than that of the suitable impedance for this unit. • When you are installing a 12 decibels/octave system in your car, the following points must be considered. In a 12 decibels/octave system where both a choke and capacitor are used in series to form a circuit, a great care must be taken when they are connected. In such a circuit, there is going to be an increase in the current which by-passes the speaker with frequencies at around the crossover frequency. If audio signals are continued to be fed into the crossover frequency area, it may cause the amplifier to become abnormally hot or the fuse will be blown. Also if the speaker is disconnected, a series-resonant circuit will be formed by the choke and the capacitor. In this case, the impedance in the resonance area will decrease dramatically resulting in a short circuit like situation causing a damage to the amplifier. Therefore, make sure that a speaker is connected to such a circuit at all times. Subwoofers (min. 2 Ω) Haut-parleur d’extrêmes graves (min. 2 Ω) High Level Input Connection (As a Monaural Amplifier for a Subwoofer) Connexion d’entrée à haut niveau (Comme amplificateur monaural pour un haut-parleur d’extrêmes graves) Left speaker Haut-parleur gauche For details on the settings of switches and controls, refer to “Location and Function of Controls.” Note In this system, the volume of the subwoofers will be controlled by the car audio unit fader control. Pour plus de détails sur les réglages des commutateurs et commandes, reportez-vous à « Emplacement et fonction des commandes ». Remarque Dans ce système, le volume des haut-parleurs d’extrêmes graves est contrôlé par la commande de balance avant/arrière de l’autoradio. Car audio unit Autoradio Right speaker Haut-parleur droit 2 * BTL BTL Subwoofer (min. 4 Ω) Haut-parleur d’extrêmes graves (min. 4 Ω) For details on the settings of switches and controls, refer to “Location and Function of Controls.” Pour plus de détails sur les réglages des commutateurs et commandes, reportez-vous à « Emplacement et fonction des commandes ». Note If you wish to use a subwoofer as a monaural speaker, connect the speaker as illustrated above. The output signals to the subwoofer will be the combination of both right and left output signals. Remarque Si vous désirez utiliser un haut-parleur d’extrêmes graves comme haut-parleur monaural, raccordez le haut-parleur comme illustré ci-dessus. Les signaux de sortie vers le haut-parleur d’extrêmes graves seront une combinaison des signaux de sortie droit et gauche. 5 XM-SD22X High Level Input Connection (2-Speaker System) Connexion d’entrée à haut niveau (Système à 2 haut-parleurs) White Blanc Left speaker output Sortie haut-parleur gauche Black-striped cord Cordon rayé noir Grey Gris 2 Car audio unit Autoradio Right speaker output Sortie haut-parleur droit Black-striped cord Cordon rayé noir * Left speaker (min. 2 Ω) Right speaker (min. 2 Ω) Haut-parleur gauche (min. 2 Ω) Haut-parleur droit (min. 2 Ω) For details on the settings of switches and controls, refer to “Location and Function of Controls.” Pour plus de détails sur les réglages des commutateurs et commandes, reportez-vous à « Emplacement et fonction des commandes ». High Level Input Connection (As a Monaural Amplifier) Connexion d’entrée à haut niveau (Comme amplificateur monaural) Black-striped cord Cordon rayé noir Left speaker output Sortie haut-parleur gauche Black-striped cord Cordon rayé noir Right speaker output Sortie haut-parleur droit Car audio unit Autoradio Black-striped cord Cordon rayé noir Black-striped cord Cordon rayé noir 2 2 * BTL * BTL BTL BTL Left speaker (min. 4 Ω) Right speaker (min. 4 Ω) Haut-parleur gauche (min. 4 Ω) Haut-parleur droit (min. 4 Ω) For details on the settings of switches and controls, refer to “Location and Function of Controls.” Pour plus de détails sur les réglages des commutateurs et commandes, reportez-vous à « Emplacement et fonction des commandes ». * High Level Input Connector * Connecteur d’entrée à haut niveau Grey/Black striped Gris/Rayé noir Grey Gris 6 White/Black striped Blanc/Rayé noir White Blanc XM-SD22X SECTION 2 DISASSEMBLY Note : This set can be disassemble according to the following sequence. SET 2-1. BOTTOM PLATE (Page 7) 2-2. MAIN BOARD SECTION (Page 8) 2-3. MAIN BOARD (Page 8) 2-4. LED BOARD (Page 9) Note : Follow the disassembly procedure in the numerical order given. 2-1. BOTTOM PLATE 2 two screws (+BTP 3 x 6) 1 two screws (+BTP 3 x 6) 4 bottom plate 5 insulating sheet 3 two screws (+BTP 3 x 6) 7 XM-SD22X 2-2. MAIN BOARD SECTION 4 screw (+P 3 x 8) 3 three screws (+P 3 x 8) 5 MAIN board section 2 three screws (+P 3 x 8) 1 four screws (+P 3 x 8) heat sink (main) 6 CN810 2-3. MAIN BOARD 4 MAIN board 2 three screws (+P 3 x 8) 3 front panel 1 two screws (+P 3 x 8) 8 XM-SD22X 2-4. LED BOARD 1 three screws (+P 3 x 8) 2 bracket (LED) 3 LED board heat sink (main) 9 XM-SD22X SECTION 3 ELECTRICAL ADJUSTMENT Bias Adjustment Note : In Bias Adjustment, adjust RV103 if any of Q108 through Q113 are replaced. Adjust RV203 if any of Q208 through Q213 are replaced. Condition : This adjustment should be performed about one minute after the remote mode is turned on at a room temperature of about 25°C. Setting : B+, REM terminal set Stabilized Power supply GND terminal Procedure : 1. Turn the variable resistors RV103 (L-CH) and RV203 (R-CH) full clockwise as seen from the component side to minimize the bias current. 2. The input signal is to be no signal. 3. Apply the voltage to the B+ and REM terminals from the stabilized power supply and gradually increase it up to 12.0 V while checking for any unusual current. 4. Adjust each of RV103 (L-CH) and RV203 (R-CH) so that the power current of the stabilized power supply is increased in steps of 700 mA (total of 1.4 A). 5. After adjustment, check that the power current is at 1.65 to 2.05 A. Adjustment Location : Main board (component side) — MAIN BOARD (CONDUCTOR SIDE) — RV103 BIAS ADJUSTMENT (L-CH) 10 RV203 BIAS ADJUSTMENT (R-CH) XM-SD22X SECTION 4 DIAGRAMS 4-1. BLOCK DIAGRAM L (BTL) L PRE AMP IC101 (1/2) CNJ801-1,-3 -1 INPUT 6 5 S801-1 FILTER OFF PRE AMP IC102 (1/2) 1 5 6 OUTPUT (THROUGH) -3 L.P.F IC301 RV101-1 LEVEL HIGH LEVEL INPUT 3 2 1 5 RV301-1 FILTER RV102-1 LOW BOOST (40Hz) INV. AMP IC302 (2/2) CNJ801-2,-4 -4 OUTPUT (THROUGH) 3 2 3 2 1 2 3 DIFFERENTIAL AMP Q104 DRIVE AMP Q106 LOW BOOST IC202 (2/2) 1 S801-2 FILTER OFF -2 5 6 LINE SWITCH Q202 7 DIFFERENTIAL AMP Q203 +16.7V (B+) LPF RV101-2 LEVEL RV102-2 LOW BOOST (40Hz) POWER AMP Q109,Q111,Q113 SPEAKER OUT RV203 BIAS BOOST EQUALIZER Q201 –16.7V (B-) DRIVE AMP Q206 2 OVER CURRENT DET Q214 BIAS Q207 DIFFERENTIAL AMP Q204 CN805 1 BTL POWER AMP Q208,Q210,Q212 DRIVE AMP Q205 POWER AMP Q209,Q211,Q213 LINE SWITCH CONTROL Q701,702 DC OFFSET DET Q802,Q803,Q804 CN801 POWER ON/OFF Q903 REM DC-DC CONVERTER TRANSFORMER T901 DC-DC CONVERTER IC901 DC DET IC902 RECT D911,917 11 F902 B+ SWITCH Q901,Q902 +12V GND D850,852 (POWER) F901 +54V (B+) RECT D905 +45V (B+) RECT D906 -45V (B-) REF. REG SWITCHING Q913 14 D920 8 TEMP.DET Q809 TH801,803,808 PTH801 SWITCHING DRIVER Q907,Q908,Q909 DRIVER Q911 9 D820,822,827,832 –54V (B–) RECT D910 RECT D912,918 B-REG Q915 1 2 +45V (B+) -45V (B-) HI-VOLTAGE DET IC903,Q920 +16.7V (B+) RECT D909 SWITCHING Q912 PROTECT LATCH Q801,Q805,Q806 D803 B+REG Q914 D919 D851,853 (POWER) D854 PROTECTOR SWITCHING DRIVER Q904,Q905,Q906 DRIVER Q910 10 12 L OVER CURRENT DET Q114 BIAS Q107 –16.7V (B-) 2 1 R INPUT RV103 BIAS BOOST EQUALIZER Q101 CN804 BTL 1 POWER AMP Q108,Q110,Q112 DRIVE AMP Q105 7 RV301-2 FILTER PRE AMP IC202 (1/2) DIFFERENTIAL AMP Q103 +16.7V (B+) R PRE AMP IC101 (2/2) LINE SWITCH Q102 7 L.P.F IC302 (1/2) CNJ803 L LOW BOOST IC102 (2/2) LPF 3 2 7 • Signal path : AUDIO 15 16 XM-SD22X 11 11 –16.7V (B–) R XM-SD22X 4-2. SCHEMATIC DIAGRAM — MAIN SECTION (1/2) — • Refer to page 15 for Waveform and IC Block Diagram. CNJ801 IC101(1/2) C101 C231 R254 R101 R154 C102 R102 C131 IC102(1/2) C109 C130 C111 R120 R303 R104 C107 C301 C110 R107 C303 C104 C106 R105 RV101 CN803 R307 R302 R103 C207 C103 R108 R206 RV301 RV301 C108 R106 C105 C302 R109 R308 C304 IC301 R306 R305 R110 R111 IC302(1/2) C902 R309 R205 C208 S801 C112 R304 R301 C221 R310 R207 IC101(2/2) C201 R202 CNJ801 C230 C305 IC202(1/2) C209 C211 R220 R201 C202 S801 C212 IC302(2/2) C210 RV101 C204 C222 C206 C205 R203 R204 R208 R210 R209 R211 C203 R939 R940 (Page 13) R938 R941 Q920 C914 IC903 CN801 F902 L903 R942 D915 F901 R834 C915 R854 R853 R809 R815 R851 R850 CN852 CN810 R835 Q805 JR800 R833 R810 TH801 R819 R856 Q902 R820 IC901 IC902 R907 D854 D827 R828 R823 D822 D832 R811 R908 PTH801 C804 D803 D902 R844 C907 R902 Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce por tant le numéro spécifié. XM-SD22X 12 R905 C908 R821 C806 Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. 12 R911 D901 Q806 R812 R913 R906 R818 R903 R904 R857 R909 IC B/D C909 D850 Q901 R901 D820 D851 Q809 C805 TH803 D852 TH808 D853 L901 Q903 C911 C912 R910 R912 C913 XM-SD22X 4-3. SCHEMATIC DIAGRAM — MAIN SECTION (2/2) — R135 R131 C124 R801 R147 R155 R150 RV103 C123 D106 D104 Q104 R142 Q107 D107 R123 Q101 RV102 C117 R134 C118 C132 C126 R129 R802 R139 C127 R141 Q114 R160 R149 C128 Q109 R151 Q111 R124 R122 R152 D802 R144 R121 CN804 R161 R140 D109 R138 D801 Q108 D108 Q102 R800 Q110 R143 R133 Q801 R145 Q105 Q103 C116 C801 Q112 IC102(2/2) R125 R153 Q113 R146 Q106 R130 R126 R156 R148 R132 R136 C125 R235 C224 C901 R231 R247 R255 Q212 Q205 R245 Q210 Q203 R250 R243 IC202(2/2) RV203 Q208 D208 R233 Q202 D206 D204 C223 Q214 R239 C227 R249 R241 R260 R253 C216 Q204 R242 Q207 R229 C217 D207 R234 R223 C218 C232 C226 R252 D209 R238 Q209 R251 R244 Q201 RV102 Q211 (Page 12) Q206 R230 R246 Q213 R256 R224 R221 R248 R225 R222 D702 R232 R226 R704 D701 R236 C225 R702 Q804 R703 C904 C906 C905 C903 R807 R808 Q701 R701 C228 R261 R240 R806 Q803 Q702 D703 C701 C803 C802 R803 Q802 R805 R804 Q914 R916 T901 R928 Q910 D911 R943 Q904 C920 D905 R919 R918 Q905 Q911 L905 R930 R929 R914 Q906 C942 R924 L906 C921 R927 C924 Q909 C922 C923 C925 C926 L907 C917 Q908 L908 D914 C928 R933 C933 D920 R944 D918 D910 R860 XM-SD22X 13 13 C940 C860 C935 C937 D912 D906 Q907 C934 L904 C939 C916 R921 C936 D917 D913 C927 C943 R931 R932 R917 C938 L902 C918 Q913 R920 D909 C919 Q912 R915 C932 R936 D919 C941 R937 Q915 CN805 D853 JW353 JW354 14 C211 C228 C111 R857 R856 R853 R854 J XM-SD22X 14 C212 CN805 D854 R850 R851 R308 C303 RV102 CN852 R109 JW313 JW162 C201 R209 RV101 CNJ801 JW295 JW294 S801 C202 C101 C222 JW312 C102 C108 JW302 JW301 JW300 JW299 JW298 JW297 JW257 R107 Q110 JW238 Q105 Q106 C128 I CN801 CN803 CN804 R145 R103 R147 D822 JR207 D107 JW229 JW233 Q113 JW227 JW228 JW231 JW232 Q111 JW225 JW230 R148 C224 R235 D109 R146 JW237 TH803 Q109 Q114 R246 C904 C905 R803 R153 R248 C906 C903 PTH801 R240 D832 R833 JW261 JW262 JW263 C803 R806 R807 Q804 R804 R805 C227 JR106 JR215 R238 D204 R243 R828 JR216 JR217 JR107 R244 D207 D209 Q802 Q803 R140 Q108 R139 R144 JW240 JW236 JW234 JW235 JW222 JW244 JW226 C802 JW239 R151 JW213 JW241 JW242 R143 JW246 JW347 JW346 Q205 R161 JW249 R160 R245 10 Q112 R142 R150 JW334 JW220 JW221 JW219 JW214 JW181 JW305 JW304 JW303 JW253 JW254 R149 JW245 JW248 RV203 D206 R239 D208 R260 Q207 JW243 JW279 JW185 Q104 JW251 JW252 JW250 C223 JW256 JW333 JW255 JW247 JW259 R141 JW260 R132 R155 R156 JW332 R134 TP26 R152 IC101 JW345 JW163 C109 R253 JW186 JW258 JW306 JW344 R251 JW296 C117 Q103 R136 RV103 R241 C902 R131 C124 JW343 JW342 C125 R232 R256 R255 R231 C901 TP25 C126 Q203 R233 Q206 C132 JW336 JW335 R135 JW218 Q213 R205 C209 R133 R242 C123 R236 C225 JW217 C107 C207 C208 JW311 C226 JW216 JW348 C206 C205 JW310 JW212 JW211 Q211 C131 IC102 Q204 C232 Q805 JW337 JW215 JW338 R261 R249 JW331 JW349 Q214 R207 R819 Q102 R130 Q202 JW339 Q806 JW329 JW330 R811 R234 D801 D802 R250 JW340 JW341 R810 R247 9 C105 C106 IC202 R808 JW275 JW352 R154 C217 R230 D803 JW210 JW209 R129 JW276 Q809 R229 TP29 JW309 JW308 JW307 R104 C104 R106 R101 C130 R102 C103 Q702 R701 R801 C801 JW170 C922 Q209 R105 JW327 JW207 R802 JW171 JW172 JW173 C923 C921 C927 JW159 TH808 R203 Q101 R800 R834 R812 C804 C926 C928 D905 Q208 R204 C204 R206 R201 C230 R202 C203 JW280 JW274 C805 R108 Q701 C110 R906 JW273 JW196 R703 D702 JW272 R702 JW194 C701 D703 D701 JW197 JW317 JW316 JW315 R123 JW314 C116 R121 R120 R809 JW195 R126 IC902 Q801 R208 C112 JW270 JW271 R939 JW200 R223 C216 R221 R220 JW326 C118 R124 JW169 R704 R940 JW198 R226 R125 JW205 JW206 D919 D915 R942 D920 JW208 C210 RV301 JW269 JW268 JW267 JW182 JW183 R941 JW178 JW199 JW318 IC301 JW266 JW265 C939 JW175 Q201 JR100 JW264 JW190 JW191 L904 TP28 C940 C936 C934 D913 R936 C938 JW203 R225 R815 C941 JW179 TP21 C932 D917 C925 C924 JW201 JW321 R307 JW204 JW350 JW320 C218 JW319 R224 JW284 JW323 JW322 JW324 JW165 JW166 C942 JW278 JW167 IC901 R835 C911 JW277 R904 C909 C935 TP27 8 C221 JW355 JW168 JW202 R122 IC302 JW193 JW192 R222 JW289 IC903 JW325 JW283 JW282 JW161 JW281 C912 R844 C933 R937 D914 Q915 C301 R303 R304 R301 R302 R305 R306 C302 Q903 C937 R110 JW287 JW188 C908 JW164 R901 JW184 R818 JW189 R902 R905 Q914 R111 D902 JW328 Q902 R909 Q901 JW286 R944 R907 TP07 C907 TP15 JW288 JW285 JW119 R903 TP05 C806 TP22 R908 C917 JW147 D901 R913 Q912 JW187 D912 D918 TP14 C304 JW290 JW122 D820 R821 TP10 JW291 JW143 JW114 JW144 R820 Q910 R252 JW110 C918 TP12 TP20 JW174 Q210 D827 C231 JW127 JW113 TP11 R938 Q920 R254 JW129 L903 C913 R910 JW146 R912 TP19 7 D851 JW123 JW160 D911 TP13 JW292 JW136 R911 L901 D909 D910 R210 JW126 JW293 Q911 JW118 TP17 Q212 D850 JW128 JW120 JW180 6 JR800 JW124 5 R211 JW125 JW117 L902 JW133 JW109 TP16 R309 TP04 JW121 TP09 TP08 JW132 TP03 C916 JW158 JW134 JW157 JW356 JW154 D906 L907 JW116 JW145 TH801 JW153 R928 4 D852 C915 TP18 JW115 Q904 L906 JW135 C943 C919 JW151 JW150 JW152 R929 L908 JW149 JW148 Q905 JW156 JW112 JW142 JW141 TP06 C920 JW140 R943 JW111 JW138 JW139 Q909 R930 R914 R924 Q906 L905 JW130 JW107 TP02 JW108 R932 R927 B C914 JW106 JW137 Q908 F JW102 R933 D JW103 JW105 Q907 R916 3 C305 R310 TP01 JW101 JW104 Q913 R931 2 JW131 H R919 C JW100 G R918 1 R915 R917 R920 R921 E R860 C860 XM-SD22X 4-4. PRINTED WIRING BOARDS — MAIN SECTION — • Refer to page 15 for Semiconductor Location. 11 12 JR103 JR208 JR206 R823 TP24 D106 JR205 D108 C127 JR204 Q107 D104 R138 13 A TP23 FMB1 XM-SD22X • Semiconductor Location (MAIN BOARD) Ref. No. D104 D106 D107 D108 D109 D204 D206 D207 D208 D209 D701 D702 D703 D801 D802 D803 D820 D822 D827 D832 D850 D851 D852 D853 D854 D901 D902 D905 D906 D909 D910 D911 D912 D913 D914 D915 D917 D918 D919 D920 Location F-11 E-12 E-12 E-12 E-12 B-9 C-9 B-9 C-9 B-9 F-8 E-8 F-8 D-9 D-8 E-8 E-5 E-12 B-8 B-12 J-7 J-8 J-7 J-6 J-7 G-6 G-6 B-2 C-2 D-5 D-5 D-5 E-5 D-6 E-6 D-6 D-5 E-5 D-7 D-6 IC101 IC102 IC202 IC301 IC302 IC901 IC902 IC903 G-9 G-8 H-8 G-7 H-6 F-6 F-8 D-6 Q101 Q102 G-8 F-9 Ref. No. Q103 Q104 Q105 Q106 Q107 Q108 Q109 Q110 Q111 Q112 Q113 Q114 Q201 Q202 Q203 Q204 Q205 Q206 Q207 Q208 Q209 Q210 Q211 Q212 Q213 Q214 Q701 Q702 Q801 Q802 Q803 Q804 Q805 Q806 Q809 Q901 Q902 Q903 Q904 Q905 Q906 Q907 Q908 Q909 Q910 Q911 Q912 Q913 Q914 Q915 Q920 Location F-10 F-10 E-10 E-10 F-11 F-11 E-11 F-11 D-11 G-11 D-11 D-11 H-8 F-9 D-9 D-9 D-10 D-9 B-9 B-8 B-9 B-8 B-10 B-7 B-10 C-9 E-8 F-8 D-8 B-11 B-11 B-11 D-8 D-8 E-8 F-6 F-6 G-5 D-2 D-2 E-2 G-2 F-2 F-2 E-4 E-4 E-2 E-2 E-6 E-6 C-6 THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) for schematic diagram: Note: • All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • % : indicates tolerance. • 2 : nonflammable resistor. • C : panel designation. Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce por tant le numéro spécifié. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. • • • • • • • • • A : B+ Line. B : B– Line. H : adjustment for repair. Power voltage is dc 14.4V and fed with regulated dc power supply from +12V and REM terminals. Voltage and waveform are dc with respect to ground under no-signal condition. Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. F : AUDIO for printed wiring boards: Note: • X : parts extracted from the component side. • : Pattern from the side which enables seeing. • IC Block Diagram IC901 TL5941NSR • Waveform 1 16 IC901 5 15 14 13 12 11 9 REF. REG. ERROR 3.0Vp-p 0.1V OSC ERROR 15 µsec 10 1 2 3 4 5 6 7 8 1V/div, 5 µsec/div 15 XM-SD22X SECTION 5 EXPLODED VIEWS NOTE: • The mechanical parts with no reference number in the exploded views are not supplied. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • Color Indication of Appearance Parts Example : KNOB, BALANCE (WHITE) ... (RED) R R Parts Color Cabinet’s Color • Accessories are given in the last of this parts list. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. 5-1. HEAT SINK (MAIN) SECTION 1 2 not supplied #2 #2 #3 #2 #2 F901 #2 #3 F902 not supplied (LED board) not supplied not supplied #2 #1 not supplied #1 Ref. No. Part No. Description 1 2 0 F901 0 F902 X-2025-547-1 2-589-409-01 1-533-743-11 1-533-743-11 PLATE ASSY, ORNAMENTAL SHEET, DOUBLE-FACE ADHESIVE FUSE (BLADE TYPE) (AUTO FUSE) (40A) FUSE (BLADE TYPE) (AUTO FUSE) (40A) 16 Remark Ref. No. #1 #2 #3 Part No. Description 7-685-545-14 SCREW +BTP 3X6 TYPE2 N-S 7-685-546-19 SCREW +BTP 3X8 TYPE2 N-S 7-685-649-79 SCREW +BVTP 3X14 TYPE2 N-S Remark XM-SD22X 5-2. MAIN BOARD SECTION not supplied Q209, 210, 213 Q108, 111, 112 53 not supplied 54 54 not supplied 53 Q208, 211, 212 Q108, 111, 112 not supplied A 60 57 56 55 57 60 59 58 57 #4 52 A 51 #4 Ref. No. Part No. Description Part No. Description 51 52 53 54 55 3-262-163-01 A-1083-419-A 3-238-413-01 3-225-183-12 3-249-786-01 PANEL (FRONT) MAIN BOARD, COMPLETE SHEET (TR), INSULATING SCREW (+PSW.TT.3XL) HEAT SINK (SUB.POWER) Remark Ref. No. Q110 Q111 Q112 Q113 Q208 X-3383-027-1 X-3383-028-1 X-3383-027-1 X-3383-028-1 X-3383-027-1 FET PAIR ASSY (N) (IRF540) (set of 3) FET PAIR ASSY (P) (IRF9540) (set of 3) FET PAIR ASSY (N) (IRF540) (set of 3) FET PAIR ASSY (P) (IRF9540) (set of 3) FET PAIR ASSY (N) (IRF540) (set of 3) Remark 56 57 58 59 60 3-225-183-32 3-225-184-12 3-253-537-01 3-912-431-01 3-912-432-01 SCREW (+PSW.TT.3XL) SCREW (+PS.TT.3XL) SCREW (M5X11) SCREW (+-P) SCREW (+-B) Q209 Q210 Q211 Q212 Q213 X-3383-028-1 X-3383-027-1 X-3383-028-1 X-3383-027-1 X-3383-028-1 FET PAIR ASSY (P) (IRF9540) (set of 3) FET PAIR ASSY (N) (IRF540) (set of 3) FET PAIR ASSY (P) (IRF9540) (set of 3) FET PAIR ASSY (N) (IRF540) (set of 3) FET PAIR ASSY (P) (IRF9540) (set of 3) Q108 Q109 X-3383-027-1 FET PAIR ASSY (N) (IRF540) (set of 3) X-3383-028-1 FET PAIR ASSY (P) (IRF9540) (set of 3) #4 7-685-646-79 SCREW +P 3X8 TYPE2 NON-SLIT 17 XM-SD22X SECTION 6 ELECTRICAL PARTS LIST MAIN NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • SEMICONDUCTORS In each case, u : µ, for example: uA.. : µA.. uPA.. : µPA.. uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. • CAPACITORS uF : µF • COILS uH : µH The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. When indicating parts by reference number, please include the board. Ref. No. Part No. Description Remark A-1083-419-A MAIN BOARD, COMPLETE ********************* 3-225-183-12 3-225-183-32 3-225-184-12 3-238-413-01 3-249-786-01 SCREW (+PSW.TT.3XL) SCREW (+PSW.TT.3XL) SCREW (+PS.TT.3XL) SHEET (TR), INSULATING HEAT SINK (SUB.POWER) 3-253-537-01 3-912-431-01 3-912-432-01 7-685-646-79 SCREW (M5X11) SCREW (+-P) SCREW (+-B) SCREW +P 3X8 TYPE2 NON-SLIT < CAPACITOR > C101 C102 C103 C104 C105 1-126-794-11 1-126-794-11 1-162-919-11 1-162-919-11 1-163-251-11 ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 4.7uF 4.7uF 22PF 22PF 100PF 20% 20% 5% 5% 5% 50V 50V 50V 50V 50V C106 C107 C108 C109 C110 1-163-251-11 1-107-826-11 1-107-826-11 1-126-796-11 1-162-927-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 100PF 0.1uF 0.1uF 22uF 100PF 5% 10% 10% 20% 5% 50V 16V 16V 50V 50V C111 C112 C116 C117 C118 1-126-794-11 1-126-794-11 1-162-927-11 1-126-794-11 1-127-715-11 ELECT ELECT CERAMIC CHIP ELECT CERAMIC CHIP 4.7uF 4.7uF 100PF 4.7uF 0.22uF 20% 20% 5% 20% 10% 50V 50V 50V 50V 16V C123 C124 C125 C126 C127 1-126-786-11 1-107-826-11 1-107-826-11 1-162-925-11 1-107-826-11 ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 47uF 0.1uF 0.1uF 68PF 0.1uF 20% 10% 10% 5% 10% 16V 16V 16V 50V 16V C128 C130 C131 C132 C201 1-137-374-11 1-162-919-11 1-128-499-11 1-162-925-11 1-126-794-11 MYLAR CERAMIC CHIP ELECT CERAMIC CHIP ELECT 0.047uF 22PF 220uF 68PF 4.7uF 5% 5% 20% 5% 20% 50V 50V 16V 50V 50V C202 C203 C204 C205 C206 1-126-794-11 1-162-919-11 1-162-919-11 1-163-251-11 1-163-251-11 ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 4.7uF 22PF 22PF 100PF 100PF 20% 5% 5% 5% 5% 50V 50V 50V 50V 50V C207 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V 18 Ref. No. Part No. Description C208 C209 C210 C211 C212 1-107-826-11 1-126-796-11 1-162-927-11 1-126-794-11 1-126-794-11 CERAMIC CHIP ELECT CERAMIC CHIP ELECT ELECT 0.1uF 22uF 100PF 4.7uF 4.7uF 10% 20% 5% 20% 20% 16V 50V 50V 50V 50V Remark C216 C217 C218 C221 C222 1-162-927-11 1-126-794-11 1-127-715-11 1-115-339-11 1-162-927-11 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 100PF 4.7uF 0.22uF 0.1uF 100PF 5% 20% 10% 10% 5% 50V 50V 16V 50V 50V C223 C224 C225 C226 C227 1-126-786-11 1-107-826-11 1-107-826-11 1-162-925-11 1-107-826-11 ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 47uF 0.1uF 0.1uF 68PF 0.1uF 20% 10% 10% 5% 10% 16V 16V 16V 50V 16V C228 C230 C231 C232 C301 1-137-374-11 1-162-919-11 1-115-339-11 1-162-925-11 1-162-927-11 MYLAR CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.047uF 22PF 0.1uF 68PF 100PF 5% 5% 10% 5% 5% 50V 50V 50V 50V 50V C302 C303 C304 C305 C701 1-162-927-11 1-127-715-11 1-107-826-11 1-162-927-11 1-126-796-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT 100PF 0.22uF 0.1uF 100PF 22uF 5% 10% 10% 5% 20% 50V 16V 16V 50V 50V C801 C802 C803 C804 C805 1-127-715-11 1-126-786-11 1-162-964-11 1-162-962-11 1-126-794-11 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT 0.22uF 47uF 0.001uF 470PF 4.7uF 10% 20% 10% 10% 20% 16V 16V 50V 50V 50V C806 C860 C901 C902 C903 1-162-964-11 1-107-826-11 1-115-339-11 1-115-339-11 1-164-161-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.1uF 0.1uF 0.1uF 0.0022uF 10% 10% 10% 10% 10% 50V 16V 50V 50V 50V C904 C905 C906 C907 C908 1-164-161-11 1-164-161-11 1-164-161-11 1-126-786-11 1-162-970-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 0.0022uF 0.0022uF 0.0022uF 47uF 0.01uF 10% 10% 10% 20% 10% 50V 50V 50V 16V 25V C909 C911 C912 C913 1-130-471-00 1-126-960-11 1-128-126-11 1-162-964-11 MYLAR ELECT ELECT CERAMIC CHIP 0.001uF 1uF 100uF 0.001uF 5% 20% 20% 10% 50V 50V 25V 50V XM-SD22X MAIN Ref. No. Part No. Description Part No. Description C914 C915 C916 C917 C918 1-162-964-11 1-137-194-81 1-137-372-11 1-128-951-21 1-128-951-21 CERAMIC CHIP FILM MYLAR ELECT ELECT 0.001uF 0.47uF 0.022uF 2200uF 2200uF 10% 5% 5% 20% 20% 50V 50V 50V 16V 16V Remark Ref. No. D803 D820 D822 D827 D832 8-719-080-34 8-719-080-34 8-719-080-34 8-719-080-34 8-719-080-34 DIODE DIODE DIODE DIODE DIODE SDS511 SDS511 SDS511 SDS511 SDS511 Remark C919 C920 C921 C922 C923 1-128-951-21 1-128-951-21 1-100-199-31 1-100-199-31 1-100-199-31 ELECT ELECT ELECT ELECT ELECT 2200uF 2200uF 2200uF 2200uF 2200uF 20% 20% 20% 20% 20% 16V 16V 50V 50V 50V D901 D902 D905 D906 D909 8-719-978-33 8-719-065-46 8-719-079-00 8-719-079-01 8-719-054-55 DIODE DIODE DIODE DIODE DIODE DTZ-TT11-6.8B 02DZ16-Z(TPH3) FCH10A15 FRH10A15 1SS306-TE85L C924 C925 C926 C927 C928 1-100-199-31 1-100-199-31 1-100-199-31 1-115-339-11 1-115-339-11 ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP 2200uF 2200uF 2200uF 0.1uF 0.1uF 20% 20% 20% 10% 10% 50V 50V 50V 50V 50V D910 D911 D912 D913 D914 8-719-054-55 8-719-079-92 8-719-079-92 8-719-065-46 8-719-065-46 DIODE DIODE DIODE DIODE DIODE 1SS306-TE85L 1SR159-200TE25 1SR159-200TE25 02DZ16-Z(TPH3) 02DZ16-Z(TPH3) C932 C933 C934 C935 C936 1-104-666-11 1-104-666-11 1-130-495-00 1-130-495-00 1-104-666-11 ELECT ELECT MYLAR MYLAR ELECT 220uF 220uF 0.1uF 0.1uF 220uF 20% 20% 5% 5% 20% 25V 25V 50V 50V 25V D915 D917 D918 D919 D920 8-719-065-42 8-719-079-92 8-719-079-92 8-719-080-34 8-719-080-34 DIODE DIODE DIODE DIODE DIODE 02DZ15-Y(TPH3) 1SR159-200TE25 1SR159-200TE25 SDS511 SDS511 C937 C938 C939 C940 C941 1-104-666-11 1-128-576-11 1-128-576-11 1-115-339-11 1-115-339-11 ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP 220uF 100uF 100uF 0.1uF 0.1uF 20% 20% 20% 10% 10% 25V 63V 63V 50V 50V C942 C943 1-162-968-11 CERAMIC CHIP 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 0.0047uF 10% 50V 50V < FUSE > 0 F901 0 F902 1-533-743-11 FUSE (BLADE TYPE) (AUTO FUSE) (40A) 1-533-743-11 FUSE (BLADE TYPE) (AUTO FUSE) (40A) < IC > < TERMINAL BOARD > CN801 CN804 CN805 1-694-983-11 TERMINAL BOARD (3P+FUSE) (REM,+12V,GND,40A,40A) 1-694-984-11 TERMINAL BOARD (2P) (SPEAKER OUT (L)) 1-694-984-11 TERMINAL BOARD (2P) (SPEAKER OUT (R)) IC101 IC102 IC202 IC301 IC302 8-759-710-97 8-759-710-97 8-759-710-97 8-759-909-71 8-759-909-71 IC IC IC IC IC NJM4565M-D NJM4565M-D NJM4565M-D BA4558F BA4558F IC901 6-703-643-01 IC TL594INSR < PHOTO TRANSISTOR > < CONNECTOR > * CN803 CN810 1-691-785-11 PIN, CONNECTOR (PC BOARD) 4P (HIGH LEVEL INPUT) 1-506-468-11 PIN, CONNECTOR 3P < JACK > IC902 IC903 6-600-354-01 PHOTO TRANSISTOR PC-17K1 6-600-354-01 PHOTO TRANSISTOR PC-17K1 < JUMPER RESISTOR > < DIODE > JR100 JR103 JR106 JR107 JR204 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-295-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 CNJ801 1-779-078-41 JACK, PIN 4P (INPUT,OUTPUT (THROUGH)) D104 D106 D107 D108 D109 8-719-083-60 8-719-082-03 8-719-082-03 8-719-080-34 8-719-080-34 DIODE DIODE DIODE DIODE DIODE UDZSTE-174.7B MM3Z15VT1 MM3Z15VT1 SDS511 SDS511 JR205 JR206 JR207 JR208 JR215 1-216-295-11 1-216-295-11 1-216-295-11 1-216-295-11 1-216-295-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 D204 D206 D207 D208 D209 8-719-083-60 8-719-082-03 8-719-082-03 8-719-080-34 8-719-080-34 DIODE DIODE DIODE DIODE DIODE UDZSTE-174.7B MM3Z15VT1 MM3Z15VT1 SDS511 SDS511 JR216 JR217 1-216-295-11 SHORT CHIP 1-216-295-11 SHORT CHIP 0 0 D701 D702 D703 D801 D802 8-719-978-33 8-719-080-34 8-719-080-34 8-719-080-34 8-719-080-34 DIODE DIODE DIODE DIODE DIODE DTZ-TT11-6.8B SDS511 SDS511 SDS511 SDS511 < COIL > L901 L902 L903 L904 L905 1-456-139-12 1-410-396-71 1-456-139-12 1-410-396-71 1-410-396-71 INDUCTOR FERRITE INDUCTOR FERRITE FERRITE The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. 35uH 0.45uH 35uH 0.45uH 0.45uH Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. 19 XM-SD22X MAIN Ref. No. L906 L907 L908 Part No. Description Remark 1-410-396-71 FERRITE 1-410-396-71 FERRITE 1-410-396-71 FERRITE 0.45uH 0.45uH 0.45uH Ref. No. Q914 Q915 Q920 Part No. < THERMISTOR (POSITIVE) > PTH801 1-805-163-21 THERMISTOR, POSITIVE < TRANSISTOR > Q101 Q102 Q103 Q104 Q105 8-729-034-51 6-550-686-01 6-550-031-01 6-550-032-01 6-550-691-01 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR Q106 Q107 Q108 Q109 Q110 6-550-692-01 8-729-041-66 X-3383-027-1 X-3383-028-1 X-3383-027-1 TRANSISTOR KTC2025L-Y TRANSISTOR 2SC4015TV2 FET PAIR ASSY (N) (IRF540) (set of 3) FET PAIR ASSY (P) (IRF9540) (set of 3) FET PAIR ASSY (N) (IRF540) (set of 3) Q111 Q112 Q113 Q114 Q201 X-3383-028-1 X-3383-027-1 X-3383-028-1 8-729-034-51 8-729-034-51 FET PAIR ASSY (P) (IRF9540) (set of 3) FET PAIR ASSY (N) (IRF540) (set of 3) FET PAIR ASSY (P) (IRF9540) (set of 3) TRANSISTOR KTC3875 TRANSISTOR KTC3875 Q202 Q203 Q204 Q205 Q206 6-550-686-01 6-550-031-01 6-550-032-01 6-550-691-01 6-550-692-01 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR Q207 Q208 Q209 Q210 Q211 8-729-041-66 X-3383-027-1 X-3383-028-1 X-3383-027-1 X-3383-028-1 TRANSISTOR 2SC4015TV2 FET PAIR ASSY (N) (IRF540) (set of 3) FET PAIR ASSY (P) (IRF9540) (set of 3) FET PAIR ASSY (N) (IRF540) (set of 3) FET PAIR ASSY (P) (IRF9540) (set of 3) Q212 Q213 Q214 Q701 Q702 X-3383-027-1 X-3383-028-1 8-729-034-51 6-550-690-01 8-729-034-51 FET PAIR ASSY (N) (IRF540) (set of 3) FET PAIR ASSY (P) (IRF9540) (set of 3) TRANSISTOR KTC3875 TRANSISTOR KTA1661 TRANSISTOR KTC3875 Q801 Q802 Q803 Q804 Q805 8-729-034-50 8-729-034-51 8-729-034-50 8-729-034-51 8-729-034-50 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR KTA1504 KTC3875 KTA1504 KTC3875 KTA1504 Q806 Q809 Q901 Q902 Q903 8-729-034-51 6-550-693-01 8-729-052-82 8-729-034-50 8-729-034-51 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR KTC3875 KTC4373 KTA1281Y-AT KTA1504 KTC3875 Q904 Q905 Q906 Q907 Q908 6-550-341-01 6-550-341-01 6-550-341-01 6-550-341-01 6-550-341-01 FET FET FET FET FET Q909 Q910 Q911 Q912 Q913 6-550-341-01 6-550-693-01 6-550-693-01 8-729-034-51 8-729-034-51 FET FKV550N TRANSISTOR KTC4373 TRANSISTOR KTC4373 TRANSISTOR KTC3875 TRANSISTOR KTC3875 20 KTC3875 KTC2875-B-RTK HN4C06J-GRBL(TE85R) HN4A06J-GRBL(TE85R) KTA1045L-Y KTC2875-B-RTK HN4C06J-GRBL(TE85R) HN4A06J-GRBL(TE85R) KTA1045L-Y KTC2025L-Y FKV550N FKV550N FKV550N FKV550N FKV550N Description Remark 6-550-693-01 TRANSISTOR KTC4373 6-550-690-01 TRANSISTOR KTA1661 6-550-693-01 TRANSISTOR KTC4373 < RESISTOR > R101 R102 R103 R104 R105 1-216-837-11 1-216-837-11 1-216-837-11 1-216-837-11 1-216-206-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP 22K 22K 22K 22K 2.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/8W R106 R107 R108 R109 R110 1-216-845-11 1-216-845-11 1-216-833-11 1-216-033-00 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP 100K 100K 10K 220 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R111 R120 R121 R122 R123 1-216-845-11 1-216-077-11 1-216-843-11 1-216-295-11 1-216-827-11 METAL CHIP RES-CHIP METAL CHIP SHORT CHIP METAL CHIP 100K 15K 68K 0 3.3K 5% 5% 5% 1/10W 1/10W 1/10W 5% 1/10W R124 R125 R126 R129 R130 1-216-045-00 1-216-837-11 1-216-829-11 1-216-841-11 1-216-829-11 RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 680 22K 4.7K 47K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R131 R132 R133 R134 R135 1-216-829-11 1-216-829-11 1-216-077-11 1-216-077-11 1-216-033-00 METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP 4.7K 4.7K 15K 15K 220 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R136 R138 R139 R140 R141 1-216-033-00 1-216-821-11 1-216-845-11 1-216-845-11 1-249-421-11 RES-CHIP METAL CHIP METAL CHIP METAL CHIP CARBON 220 1K 100K 100K 2.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/4W R142 R143 R144 R145 R146 1-249-428-11 1-216-017-11 1-216-017-11 1-216-017-11 1-216-017-11 CARBON RES-CHIP RES-CHIP RES-CHIP RES-CHIP 8.2K 47 47 47 47 5% 5% 5% 5% 5% 1/4W 1/10W 1/10W 1/10W 1/10W R147 R148 R149 R150 R151 1-216-017-11 1-216-017-11 1-234-499-11 1-234-499-11 1-234-499-11 RES-CHIP 47 5% 1/10W RES-CHIP 47 5% 1/10W ENCAPSULATED COMPONENT 0.22X2 5W ENCAPSULATED COMPONENT 0.22X2 5W ENCAPSULATED COMPONENT 0.22X2 5W R152 R153 R154 R155 R156 1-215-880-31 1-216-853-11 1-216-065-11 1-216-829-11 1-216-829-11 METAL OXIDE METAL CHIP RES-CHIP METAL CHIP METAL CHIP 10 470K 4.7K 4.7K 4.7K 5% 5% 5% 5% 5% 2W F 1/10W 1/10W 1/10W 1/10W R160 R161 R201 R202 R203 1-216-827-11 1-216-821-11 1-216-837-11 1-216-837-11 1-216-837-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 3.3K 1K 22K 22K 22K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R204 R205 R206 1-216-837-11 METAL CHIP 1-216-206-00 RES-CHIP 1-216-845-11 METAL CHIP 22K 2.2K 100K 5% 5% 5% 1/10W 1/8W 1/10W XM-SD22X MAIN Ref. No. Part No. Description Part No. Description R207 R208 R209 R210 R211 1-216-845-11 1-216-833-11 1-216-033-00 1-216-845-11 1-216-845-11 METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP 100K 10K 220 100K 100K 5% 5% 5% 5% 5% Remark 1/10W 1/10W 1/10W 1/10W 1/10W Ref. No. R803 R804 R805 R806 R807 1-216-857-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1M 10K 10K 10K 10K 5% 5% 5% 5% 5% Remark 1/10W 1/10W 1/10W 1/10W 1/10W R220 R221 R222 R223 R224 1-216-077-11 1-216-843-11 1-216-295-11 1-216-827-11 1-216-045-00 RES-CHIP METAL CHIP SHORT CHIP METAL CHIP RES-CHIP 15K 68K 0 3.3K 680 5% 5% 1/10W 1/10W 5% 5% 1/10W 1/10W R808 R809 R810 R811 R812 1-216-857-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1M 10K 10K 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R225 R226 R229 R230 R231 1-216-837-11 1-216-829-11 1-216-841-11 1-216-829-11 1-216-829-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 22K 4.7K 47K 4.7K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R815 R818 R819 R820 R821 1-216-295-11 1-216-845-11 1-216-815-11 1-216-817-11 1-216-827-11 SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 0 100K 330 470 3.3K 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R232 R233 R234 R235 R236 1-216-829-11 1-216-077-11 1-216-077-11 1-216-033-00 1-216-033-00 METAL CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 4.7K 15K 15K 220 220 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R823 R828 R833 R834 R835 1-216-828-11 1-216-828-11 1-216-829-11 1-216-841-11 1-216-295-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP 3.9K 3.9K 4.7K 47K 0 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R238 R239 R240 R241 R242 1-216-821-11 1-216-845-11 1-216-845-11 1-249-421-11 1-249-428-11 METAL CHIP METAL CHIP METAL CHIP CARBON CARBON 1K 100K 100K 2.2K 8.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/4W 1/4W R844 R860 R901 R902 R903 1-216-833-11 1-216-206-00 1-216-825-11 1-216-827-11 1-216-837-11 METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP 10K 2.2K 2.2K 3.3K 22K 5% 5% 5% 5% 5% 1/10W 1/8W 1/10W 1/10W 1/10W R243 R244 R245 R246 R247 1-216-017-11 1-216-017-11 1-216-017-11 1-216-017-11 1-216-017-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 47 47 47 47 47 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R904 R905 R906 R907 R908 1-216-836-11 1-216-849-11 1-216-065-11 1-216-190-00 1-216-190-00 METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP 18K 220K 4.7K 470 470 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/8W 1/8W R248 R249 R250 R251 R252 1-216-017-11 1-234-499-11 1-234-499-11 1-234-499-11 1-215-880-31 RES-CHIP 47 5% 1/10W ENCAPSULATED COMPONENT 0.22X2 5W ENCAPSULATED COMPONENT 0.22X2 5W ENCAPSULATED COMPONENT 0.22X2 5W METAL OXIDE 10 5% 2W F R909 R910 R911 R912 R913 1-216-061-11 1-216-073-00 1-216-073-00 1-216-073-00 1-216-186-00 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 3.3K 10K 10K 10K 330 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/8W R253 R254 R255 R256 R260 1-216-853-11 1-216-049-11 1-216-829-11 1-216-829-11 1-216-827-11 METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP 470K 1K 4.7K 4.7K 3.3K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R914 R915 R916 R917 R918 1-216-049-11 1-216-049-11 1-216-009-11 1-216-009-11 1-216-049-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1K 1K 22 22 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R261 R301 R302 R303 R304 1-216-821-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 10K 10K 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R919 R920 R921 R924 R927 1-216-049-11 1-216-049-11 1-216-049-11 1-216-049-11 1-216-049-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1K 1K 1K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R305 R306 R307 R308 R309 1-216-833-11 1-216-833-11 1-216-827-11 1-216-827-11 1-216-837-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 10K 3.3K 3.3K 22K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R928 R929 R930 R931 R932 1-216-001-00 1-216-001-00 1-216-001-00 1-216-001-00 1-216-001-00 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 10 10 10 10 10 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R310 R701 R702 R703 R704 1-216-837-11 1-216-839-11 1-216-845-11 1-216-833-11 1-216-841-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 22K 33K 100K 10K 47K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R933 R936 R937 R938 R939 1-216-001-00 1-216-825-11 1-216-825-11 1-216-033-00 1-216-821-11 RES-CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP 10 2.2K 2.2K 220 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R800 R801 R802 1-216-841-11 METAL CHIP 1-216-841-11 METAL CHIP 1-216-841-11 METAL CHIP 47K 47K 47K 5% 5% 5% 1/10W 1/10W 1/10W R940 R941 R942 1-216-089-11 RES-CHIP 1-216-843-11 METAL CHIP 1-216-837-11 METAL CHIP 47K 68K 22K 5% 5% 5% 1/10W 1/10W 1/10W 21 XM-SD22X MAIN Ref. No. R943 R944 LED Part No. Description 1-216-009-11 RES-CHIP 1-216-009-11 RES-CHIP Remark 22 22 5% 5% Ref. No. Remark 2-514-765-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH) 2-514-765-21 MANUAL, INSTRUCTION (GERMAN,ITALIAN) (AEP,UK,E) 2-514-765-31 MANUAL, INSTRUCTION (SPANISH, TRADITIONAL CHINESE) (AEP,UK,E) 2-514-765-41 MANUAL, INSTRUCTION (DUTCH,PORTUGUESE) (AEP,UK,E) 2-514-765-51 MANUAL, INSTRUCTION (SWEDISH,POLISH) (AEP,UK,E) 1-227-558-11 RES, VAR, CARBON 5KX2 (LEVEL) 1-227-558-11 RES, VAR, CARBON 5KX2 (LOW BOOST (40Hz)) 1-227-557-11 RES, VAR, CARBON 20KX2 (FILTER) < CERMET RESISTOR > RV103 RV203 Description ACCESSORIES ************ < VARIABLE RESISTOR > RV101 RV102 RV301 Part No. 1/10W 1/10W 1-241-764-11 RES, ADJ, CERMET 10K 1-241-764-11 RES, ADJ, CERMET 10K < SWITCH > S801 2-514-765-61 MANUAL, INSTRUCTION (GREEK,RUSSIAN) (AEP,UK,E) ************************************************************* 1-692-990-21 SWITCH, SLIDE (FILTER) < TRANSFORMER > T901 PARTS FOR INSTALLATION AND CONNECTIONS *************************************** 1-439-635-21 TRANSFORMER, DC-DC CONVERTER < THERMISTOR (NEGATIVE) > 101 TH801 1-804-301-11 THERMISTOR, CHIP (NEGATIVE) TH803 1-804-301-11 THERMISTOR, CHIP (NEGATIVE) TH808 1-804-301-11 THERMISTOR, CHIP (NEGATIVE) ************************************************************* 102 103 3-367-410-11 SCREW (DIA. 5X15), TAPPING (MOUNTING SCREW) 1-690-779-31 CORD (WITH CONNECTOR) (0.2m) 3-249-791-01 COVER (POWER) 101 102 103 LED BOARD ********** φ 5 × 15 (× 4) < DIODE > D850 D851 D852 D853 D854 6-501-118-01 6-501-118-01 6-501-118-01 6-501-118-01 6-501-117-01 LED LED LED LED LED SEL6E10C-STP5 (POWER) SEL6E10C-STP5 (POWER) SEL6E10C-STP5 (POWER) SEL6E10C-STP5 (POWER) SEL2110W-TP3 (PROTECTOR) < JUMPER RESISTOR > JR800 1-216-296-11 SHORT CHIP 0 < RESISTOR > R850 R851 R853 R854 R856 1-216-815-11 1-216-815-11 1-216-815-11 1-216-815-11 1-216-815-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 330 330 330 330 330 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R857 1-216-815-11 METAL CHIP 330 5% 1/10W ************************************************************* 22 0.2 m XM-SD22X MEMO 23 XM-SD22X REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver. 1.0 24 Date 2004.12 Description of Revision New ">
Link público atualizado
O link público para o seu chat foi atualizado.
