25L-M100/180/S100/180 CL25M10,CL25S18 SERVICE MANUAL S49F325L-M100 COLOR TELEVISION Chassis No. SN-91 25L-M100/180 CL25M10 25L-S100/180 CL25S18 MODELS 25L-M100/180, 25L-S100/180 CL25M10, CL25S18 In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. CONTENTS Page » ELECTRICAL SPECIFICATIONS........................................................................................................ 1 » IMPORTANT SERVICE SAFETY PRECAUTION ............................................................................... 2 » LOCATION OF USER'S CONTROL .................................................................................................... 6 » INSTALLATION AND SERVICE INSTRUCTIONS ............................................................................ 10 » CHASSIS LAYOUT ........................................................................................................................... 16 » BLOCK DIAGRAM ............................................................................................................................ 18 » SCHEMATIC DIAGRAMS ................................................................................................................. 20 » PRINTED WIRING BOARD ASSEMBLIES ....................................................................................... 38 » REPLACEMENT PARTS LIST .......................................................................................................... 41 » PACKING OF THE SET ..................................................................................................................... 49 ELECTRICAL SPECIFICATIONS POWER INPUT ................................................... 120 V AC 60 Hz POWER RATING 25L-M100/180, CL25M10 ................................................. 105 W 25L-S100/180, CL25S18 .................................................. 110 W PICTURE SIZE ........................................... 2,032cm2 (315sq inch) CONVERGENCE ............................................................. Magnetic SWEEP DEFLECTION ..................................................... Magnetic FOCUS ............................................... Hi-Bi-Potential Electrostatic INTERMEDIATE FREQUENCIES Picture IF Carrier Frequency ..................................... 45.75 MHz Sound IF Carrier Frequency ...................................... 41.25 MHz Color Sub-Carrier Frequency ..................................... 42.17 MHz (Nominal) AUDIO POWER 25L-M100/180, CL25M10 ............... 1.3W (at 10% distortion and Dual CH Operate) 25L-S100/180, CL25S18 .... 1.3W +1.3W (at 10% distortion and Dual CH Operate) SPEAKER SIZE ...................................................................... 8 cm (Round) VOICE COIL IMPEDANCE ............................. 32 ohm at 400 Hz ANTENNA INPUT IMPEDANCE VHF/UHF .................................................... 75 ohm Unbalanced TUNING RANGES VHF-Channels .............................................................. 2 thru 13 UHF-Channels ............................................................ 14 thru 69 CATV Channels .......................................................... 1 thru 125 (EIA, Channel Plan U.S.A.) Specifications are subject to change without prior notice. This document has been published to be used for after sales service only. The contents are subject to change without notice. SHARP CORPORATION 1 25L-M100/180/S100/180 CL25M10,CL25S18 IMPORTANT SERVICE SAFETY PRECAUTION Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow: WARNING X-RADIATION AND HIGH VOLTAGE LIMITS 1. For continued safety, no modification of any circuit should be attempted. 2. Disconnect AC power before servicing. 3. Semiconductor heat sinks are potential shock hazards when the chassis is operating. 4. The chassis in this receiver has two ground systems which are separated by insulating material. The nonisolated (hot) ground system is for the B+ voltage regulator circuit and the horizontal output circuit. The isolated ground system is for the low B+ DC voltages and the secondary circuit of the high voltage transformer. To prevent electrical shock use an isolation transformer between the line cord and power receptacle, when servicing this chassis. 1. Be sure all service personnel are aware of the procedures and instructions covering X-radiation. The only potential source of X-ray in current solid state TV receivers is the picture tube. However, the picture tube does not emit measurable X-Ray radiation, if the high voltage is as specified in the "High Voltage Check" instructions. It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the picture tube including the lead in the glass material. The important precaution is to keep the high voltage below the maximum level specified. 2. It is essential that servicemen have available at all times an accurate high voltage meter. The calibration of this meter should be checked periodically. 3. High voltage should always be kept at the rated value −no higher. Operation at higher voltages may cause a failure of the picture tube or high voltage circuitry and;also, under certain conditions, may produce radiation in exceeding of desirable levels. 4. When the high voltage regulator is operating properly there is no possibility of an X-radiation problem. Every time a color chassis is serviced, the brightness should be tested while monitoring the high voltage with a meter to be certain that the high voltage does not exceed the specified value and that it is regulating correctly. 5. Do not use a picture tube other than that specified or make unrecommended circuit modifications to the high voltage circuitry. 6. When trouble shooting and taking test measurements on a receiver with excessive high voltage, avoid being unnecessarily close to the receiver. Do not operate the receiver longer than is necessary to locate the cause of excessive voltage. 4A 125V CAUTION: FOR CONTINUED PROTECTION AGAINST A RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 4A125V FUSE. SERVICING OF HIGH VOLTAGE SYSTEM AND PICTURE TUBE When servicing the high voltage system, remove the static charge by connecting a 10k ohm resistor in series with an insulated wire (such as a test probe) between the picture tube ground and the anode lead. (AC line cord should be disconnected from AC outlet.) 1. Picture tube in this receiver employs integral implosion protection. 2. Replace with tube of the same type number for continued safety. 3. Do not lift picture tube by the neck. 4. Handle the picture tube only when wearing shatterproof goggles and after discharging the high voltage anode completely. 2 25L-M100/180/S100/180 CL25M10,CL25S18 IMPORTANT SERVICE SAFETY PRECAUTION (Continued) • Connect the resistor connection to all exposed metal parts having a return to the chassis (antenna, metal cabinet, screw heads, knobs and control shafts, escutcheon and etc.) and measure the AC voltage drop across the resistor. AII checks must be repeated with the AC ine cord plug connection reversed. (If necessary, a nonpolarized adapter plug must be used only for the purpose of completing these check.) Any current measured must not exceed 0.5 milliamp. Any measurements not within the limits outlined above indicate of a potential shock hazard and corrective action must be taken before returning the instrument to the customer. BEFORE RETURNING THE RECEIVER (Fire & Shock Hazard) Before returning the receiver to the user, perform the following safety checks. 1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the receiver. 2. Inspect all protective devices such as non-metallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacity networks, mechanical insulators and etc. 3. To be sure that no shock hazard exists, check for leakage current in the following manner. • Plug the AC cord directly into a 120 volt AC outlet, (Do not use an isolation transformer for this test). • Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal cabinet parts and a known earth ground, such as electrical conduit or electrical ground connected to earth ground. • Use an AC voltmeter having with 5000 ohm per volt, or higher, sensitivity to measure the AC voltage drop across the resistor. AC VOLTMETER 1.5k ohm 10W 0.15µF TEST PROBE TO EXPOSED METAL PARTS CONNECT TO KNOWN EARTH GROUND 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 SAFETY NOTICE For continued protection, replacement parts must be identical to those used in the original circuit. The use of substitute replacement parts which do not have the same safety characteristics as the factory recommended replacement parts shown in this service manual, may create shock, fire, X-radiation or other hazards. Many electrical and mechanical parts in television receivers have special safety-related characteristics. These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily increased by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this manual; electrical components having such features are identified by "å" and shaded areas in the Replacement Parts Lists and Schematic Diagrams. 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 3 25L-M100/180/S100/180 CL25M10,CL25S18 PRECAUTIONS A PRENDRE LORS DE LA REPARATION Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux conseils suivants. AVERTISSEMENT LIMITES DES RADIATIONS X ET DE LA HAUTE TENSION 1. N'entreprendre aucune modification de tout circuit. C'est dangereux. 2. Débrancher le récepteur avant toute réparation. 3. Les déversoirs thermiques à semi-conducteurs peuvent présenter un danger de choc électrique lorsque le réceqteur est en marche. 4. Le châssis de ce récepteur possède deux systèmes de masse qui sont séparées par du matériel d'isolation. Le système de masse non-isolée (sous tension) est pour le circuit du régulateur de tension B+ et le circuit de sortie horizontale. Le système de masse isolée est pour les tensions DC B+ basses et le circuit secondaire du transformateur haute tension. Pour éviter tout risque d'électrocution lors de l'entretien de ce châssis, utiliser un transformateur d'isolation entre le cordon de ligne et la prise de courant. 4A 125V 1. Tout le personnel réparateur doit être instruit des instructions et procédés relatifs aux radiations X. Le tube-image, seule source de rayons X dons les téleviseurs transistorisés, n'émet pourtant pas de rayons mesurables si la haute tension est maintenue à un niveau préconisé dans la section "Vérification de la haute tension". C'est seulement quand la haute tension est excessive que les rayons X peuvent entrer dans l'enveloppe du tube-image y compris le conducteur de verre. Il est important de maintenir la haute tension en-dessous du niveau spécifié. 2. Il est essentiel que le réparateur ait sous la main un voltmètre à haute tension qui doit être périodiquement étalonné. 3. La haute tension doit toujours être maintenue à la valeur de régime -et pas plus haute. L'opération à des tensions plus élevées peut entraîner une panne du tube-image ou du circuit à haute tension et, dans certaines conditions, peut entraîner une radiation dépassant les niveaux préscrits. 4. Quand le régulateur à haute tension fonctionne correctement, il n'y a aucun problème de radiation X. Chaque fois qu'un châssis couleurs est réparé, la luminosité doit être examinée bout en contrôlant la haute tension à l'aide d'un voltmètre pour s'assurer que la haute tension ne dépasse pas la valeur spécifiée et qu'elle soit correctement réglée. 5. Ne pas utiliser un tube-image autre que celui spécifié et ne pas effectuer de modifications déconseillées du circuit à haute tension. 6. Lors de la recherche des pannes et des mesures d'essai sur un récepteur qui présente une haute tension excessive, éviter de s'approcher inutilement du récepteur. Ne pas faire fonctionner le récepteur plus longtemps que nécessaire pour localiser la cause de la tension excessive. PRECAUTION: POUR LA PROTECTION CONTINUE CONTRE LES RISQUES D'INCENDIE, REMPLACER LE FUSIBLE PAR UN FUSIBLE DE MEME TYPE 4A-125V. REPARATION DU SYSTEME A HAUTE TENSION ET DU TUBE-IMAGE Lors de la réparation de ce systéme, supprimer la charge statique en branchant une résistance de 10 kΩ en série avec un fil isolé (comme une sonde d'essai) entre la mise à la terre du tube-image et le fil d'anodel. (Le corden d'alimentation doit être retiré de la prise murale.) 1. Le tube image dans ce récepteur emploie une protection intégrée contre l'implosion. 2. Par mesure de sécurité, changer le tube-image pour un tube du même numéro de type. 3. Ne pas lever le tube-image par son col. 4. Ne manipuler le tube-image qu'en porant des lunettes incassables et qu'après avoir déchargé totalement la haute tension. 4 25L-M100/180/S100/180 CL25M10,CL25S18 PRECAUTIONS A PRENDRE LORS DE LA REPARATION (Suite) • Toucher avec la sonde d'essai les pièces métalliques exposées qui présentent une voie de retour au châssis (antenne, coffret métallique, tête des vis, arbres de commande et des boutons, écusson, etc.) et mesurer la chute de tension CA en-travers de la résistance. Toutes les vérifications doivent être refaites après avoir inversé la fiche du cordon d'alimentation. (Si nécessaire, une prise d'adpatation non polarisée peut être utilisée dans le but de terminer ces vérifications.) Tous les courants mesurés ne doivent pas dépasser 0.5 mA. Dans le cas contraire, il y a une possibilité de choc électrique qui doit être supprimée avant de rendre le récepteur au client. VERIFICATIONS CONTRE L'INCEN-DIE ET LE CHOC ELECTRIQUE Avant de rendre le récepteur à l'utilisateur, effectuer les vérifications suivantes. 1. Inspecter tous les faisceaux de câbles pour s'assurer que les fils ne soient pas pincés ou qu'un outil ne soit pas placé entre le châssis et les autres pièces métalliques du récepteur. 2. Inspecter tous les dispositifs de protection comme les boutons de commande non-métalliques, les isolants, le dos du coffret, les couvercles ou blindages de réglage et de compartiment, les réseaux de résistance-capacité, les isolateurs mécaniques, etc. 3. S'assurer qu'il n'y ait pas de danger d'électrocution en vérifiant la fuite de courant, de la facon suivante: • Brancher le cordon d'alimentation directem-ent à une prise de courant de 120V. (Ne pas utiliser de transformateur d'isolation pour cet essai). • A l'aide de deux fils à pinces, brancher une résistance de 1.5 kΩ 10 watts en parallèle avec un condensateur de 0.15µF en série avec toutes les pièces métalliques exposées du coffret et une terre connue comme une conduite électrique ou une prise de terre branchée à la terre. • Utiliser un voltmètre CA d'une sensibilité d'au moins 5000Ω/V pour mesurer la chute de tension en travers de la résistance. Voltmètre CA 1.5k ohm 10W 0.15µF SONDE D'ESSAI AUX PIECES METALLIQUES EXPOSEES BRANCHER A UNE TERRE CONNUE 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 AVIS POUR LA SECURITE identifiées par la marque " å " et hachurées dans la liste des pièces de remplacement et les diagrammes schématiques. Pour assurer la protection, ces pièces doivent être identiques à celles utilisées dans le circuit d'origine. L'utilisation de pièces qui n'ont pas les mêmes caractéristiques que les pièces recommandées par l'usine, indiquées dans ce manuel, peut provoquer des électrocutions, incendies, radiations X ou autres accidents. De nombreuses pièces, électriques et mécaniques, dans les téléviseurs présentent des caractéristiques spéciales relatives à la sécurité, qui ne sont souvent pas évidentes à vue. Le degré de protection ne peut pas être nécessairement augmentée en utilisant des pièces de remplacement étalonnées pour haute tension, puissance, etc. Les pièces de remplacement qui présentent ces caractéristiques sont identifiées dans ce manuel; les pièces électriques qui présentent ces particularités sont 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 5 25L-M100/180/S100/180 CL25M10,CL25S18 LOCATION OF USER'S CONTROL (25L-M100, CL25M10) 6 25L-M100/180/S100/180 CL25M10,CL25S18 LOCATION OF USER'S CONTROL(Continued) (25L-M180) 7 25L-M100/180/S100/180 CL25M10,CL25S18 LOCATION OF USER'S CONTROL(Continued) (25L-S100) 8 25L-M100/180/S100/180 CL25M10,CL25S18 LOCATION OF USER'S CONTROL(Continued) (25L-S180, CL25S18) 9 25L-M100/180/S100/180 CL25M10,CL25S18 INSTALLATION AND SERVICE INSTRUCTIONS Note: (1) When performing any adjustments to resistor controls and transformers use non-metallic screwdrivers or TV alignment tools. (2) Before performing adjustments, the TV set must be on at least 15 minutes. CIRCUIT PROTECTION HIGH VOLTAGE CHECK The receiver is protected by a 4.0A fuse (F701), mounted on PWB-A, wired into one side of the AC line input. High voltage is not adjustable but must be checked to verify that the receiver is operating within safe and efficient design limitations as specified checks should be as follows: X-RADIATION PROTECTOR CIRCUIT TEST 1. Connect an accurate high voltage meter between ground and anode of picture tube. 2. Operate receiver for at least 15 minutes at 120V AC line voltage, with a strong air signal or a properly tuned in test signal. 3. Enter the service mode and select the service adjustment "S19" and Bus data "01" (Y-mute on). 4. The voltage should be approximately, 28.7kV (at zero beam). If a correct reading cannot be obtained, check circuitry for malfunctioning components. After the voltage test, make Y-mute off to the normal mode. After service has been performed on the horizontal deflection system, high voltage system, B+ system, test the X-Radiation protection circuit to ascertain proper operation as follows: 1) Apply 120V AC using a variac transformer for accurate input voltage. 2) Allow for warm up and adjust all customer controls for normal picture and sound. 3) Receive a good local channel. 4) Connect a digital voltmeter to TP653 and make sure that the voltmeter reads 11.2 ±0.6V. 5) Apply external 13.8V DC at TP653 by using an external DC supply, TV must be shut off. 6) To reset the protector, unplug the AC cord and make a short circuit between TP651 and TP652. Now make sure that normal picture appears on the screen. 7) If the operation of the horizontal oscillator does not stop in step 5, the circuit must be repaired before the set is returned to the customer. 10 25L-M100/180/S100/180 CL25M10,CL25S18 For adjustments of this model, the bus data is converted to various analog signals by the D/A converter circuit. Note: There are still a few analog adjustments in this series such as focus and master screen voltage. Follow the steps below whenever the service adjustment is required. See "Table-B" to determine, if service adjustments are required. 1. Service mode To enter the service mode and exit service mode. Before putting unit into the service mode, check that customer adjustments are in the normal mode. Use the reset function in the video adjustment menu to ensure customer controls are in their proper (reset) position. While pressing the Vol-up and Ch-up buttons at the sametime, plug the AC cord into a wall socket. Now the TV set is switched on and enters the service mode. To exit the service mode, turn the television off by pressing the power button. 2. Service number selection Once in the service mode, press the Ch-up or Chdown button on the remote controller or at the set. The service adjustment number will vary in increments of one, from "S01" to "OP"(25L-M100/180, CL25M10), "S01" to "M05"(25L-S100/180, CL25S18). Select the item you wish to adjust. 3. Data number selection Press the Vol-up or down button to adjust the data number. DATA NUMBER CHANNEL SERVICE ADJUSTMENT NUMBER S01 55(085) Figure A. 11 02 25L-M100/180/S100/180 CL25M10,CL25S18 SERVICE NUMBER DATA ADJUSTMENT ITEM INITIAL VALUE ADJUSTMENT CONTENTS RANGE S01 S02 S03 S04 S05 S06 S07 S08 S09 S10 S11 S12 S13 S14 S15 S16 S17 S18 S19 S20 S21 S22 S23 OP PICTURE TINT COLOR BRIGHTNESS SHARPNESS VERTICAL PHASE HORIZONTAL PHASE RF-AGC VERTICAL AMP VCO R CUT-OFF G CUT -OFF B CUT-OFF G GAIN B GAIN TRAP(3.58MHz) BALANCE C.C.POSITION Y-MUTE ENERGY SAVE OFFSET D.D.E. OFFSET OSD SETUP TUNER SETUP OPTION (Set to each mode) 55 46 32 40 24 00 12 23 20 2C 00 00 00 7F 7F 00 20 17 00 20 03 00 00 30 00-7F 00-7F 00-7F 00-7F 00-3F 00-07 00-1F 00-3F 00-3F 00-7F 00-FF 00-FF 00-FF 00-FF 00-FF 00 or 01 00-3F 00-7F 00,01,03 00-3F 00-1F 00-03 00,01 00-FF M01 M02 M03 M04 M05 MTS LEVEL STEREO-VCO FILTER LOW SEPARATION HIGH SEPARATION 0A 20 1C 20 1B 00-0F 00-3F 00-3F 00-3F 00-3F Must be set to "28" Must be set to "00" Must be set to "00" Must be set to "20" 00= NORMAL, 01= No Y, 03= No VERTICAL Must be set to "23" Must be set to "03" Must be set to "00" Must be set to "00" "0A"=25L-M180, "02"=25L-M100, CL25M10 "26"=25L-S100, "3E"=25L-S180, CL25S18 Only for Models 25L-S100/180, CL25S18 Table - A Holding down both the CH-up/down buttons on the TV set at service mode for more than 2 seconds will automatically write the above initial values into IC2101. ADJUSTMENT NOTES PART REPLACED NECESSARY X IC2001 IC201 UNNECESSARY X Data is stored in IC2101. The adjustment is needed to compensate for characteristics of parts including IC201 and MTS level (M01). IC2101 X Holding down both the CH-up/down buttons on the TV set in the service mode for more than 2 seconds will automatically write the above initial values into IC2101. Then perform a complete adjustment. CRT X Adjust items related to picture tube only. X Adjust items related to MTS only (M01~M05). IC3001 (25L-S100/180, CL25S18) Table - B 12 25L-M100/180/S100/180 CL25M10,CL25S18 SERVICE ADJUSTMENT VCO Adjustment White Balance Adjustment 1. Connect a digital voltmeter between pin (44) of IC201 and ground. 2. Receive a good local channel. 3. Enter the service mode and select the service adjustment "S10". 4. Adjust the data so that digital voltmeter reads 2.2V. 5. Adjustment is completed, remove the voltmeter, return to "normal" mode. 1. Receive a good local channel. 2. Enter the service mode and select the service adjustment "S03" and set to "00" (minimum color)(Record original data code under adjustment "S03" before changing). "S03" does not have to be adjusted, if you selected a B/W picture or monoscope pattern. 3. Alternately adjust service adjustment data of "S14" and "S15" until a good grey scale with normal whites is obtained. 4. Select the service adjustment "S03" and adjust data to obtain normal color level. RF AGC Adjustment 1. Receive a good local channel. 2. Enter the service mode and select the service adjustment "S08". 3. Set the data value to point where no noise or beat appears. 4. Select another channel to confirm that no noise or beat appears. Note 1 : You will have to come out of the service mode to select another channel. Note 2 : Setting the data to "00" will produce a black raster. Sub-Picture Adjustment 1. Receive a good local channel. 2. Make sure the customer picture control is set to maximum. 3. Enter the service mode and select the service adjustment "S01". 4. Adjust the data value to achieve normal contrast range. Screen Adjustment Sub-Tint Adjustment 1. Connect a oscilloscope between TP854 and GND on the CRT Unit. 2. Receive a good local channel. 3. Enter the service mode and select the service adjustment "S03" and set the data value to "00" to set the color level to minimum. (Record original data code under adjustment "S03" before changing) You may skip this step, if you selected a B/W picture or monoscope pattern. 4. Select the service adjustment "S19" and adjust the data value to "01", this turn off the luminance signal (Y-mute). 5. Select the service adjustment "S04" and adjust data value to obtain 2.35 volts on the oscilloscope screen. 1. Receive a good local channel. 2. Set customer tint control to center of it's range. 3. Enter the service mode and select the service adjustment "S02". 4. Adjust "S02" data value to obtain normal flesh tones. Sub-Color Adjustment 1. Receive a good local channel. 2. Make sure the customer color control is set to center position . 3. Enter the service mode and select service adjustment "S03". 4. Adjust "S03" data value to obtain normal color level. 2.35 ±0.15VDC GND Figure B. 6. Adjust the master screen control until the raster darkens to the point where raster is barely seen. 7. Adjust the service adjustments "S11" red, "S12" green and "S13" blue to obtain a good grey scale with normal whites at low brightness level. 8. Select the service adjustment "S19" and reset data to "00". Select the service adjustment "S03" and reset data to obtain normal color level. 9. Remove oscilloscope, and reset the master screen control to obtain normal brightness range. 13 25L-M100/180/S100/180 CL25M10,CL25S18 Sub-Brightness Adjustment 3.58MHz Trap Adjustment 1. Receive a good local channel. 2. Make sure the customer brightness control is set to center position. 3. Enter the service mode and select the service adjustment "S04". 4. Adjust "S04" data value to obtain normal brightness level. 1. Receive a good local channel. 2. Enter the service mode and select the service adjustment "S16". 3. This is a two position adjustment, "00" is ON, "01" is OFF. 4. Adjust data value to "00" for normal viewing. Vertical-Size Adjustments Sharpness and Audio Balance Adjustments 1. Receive a good local channel. 2. Enter the service mode and select the service adjustment "S09". 3. While observing the top and bottom of the screen, adjust "S09" data value to proper vertical size. 1. Receive a good local channel. 2. Enter the service mode and select the service adjustments "S05" for sharpness and "S17" for balance. » Sharpness adjustment 3. Adjust data value to "28"(center of data range) for sharpness adjustment. » Audio balance adjustment 4. Adjust data value to "20"(center of data range) for Audio balance adjustment. Vertical Phase Adjustment 1. Enter the service mode and select the service adjustment "S06". 2. Adjust data value to "00". Note: This must be set "00" when changed data retrace line will appear. Energy save offset Adjustment Horizontal Position Adjustment 1. Enter the service mode and select the service adjustment "S20". 2. Adjust data value to "23". Note : This position is used to preset the level for the energy save function. 1. Receive a good local channel. 2. Enter the service mode and select the service adjustment "S07". 3. Adjust "S07" data value so that picture is centered. Other Adjustments Caption Position Adjustment (Horizontal) 1. Enter the service mode. 2. Adjust the following data values as listed below. 1. Receive a good local channel. 2. Enter the service mode and select the service adjustment "S18". 3. A black text box appears on the screen. (see Figure C below) 4. Adjust "S18" data value so that text box is positioned in the center of the screen. Figure C. 14 S21 "03" DDE OFFSET S22 "00" OSD SETUP S23 "00" TUNER SETUP 25L-M100/180/S100/180 CL25M10,CL25S18 MTS ADJUSTMENT (Only for 25L-S100/180, CL25S18) MTS Level Adjustment 1. Feed the following monaural signal to pin (14) of IC3001. Monaural signal : 300Hz, 245mVrms 2. Connect the rms voltmeter to pin (39) of IC3001. 3. Enter the service mode and select the service adjustment "M01". 4. Adjust the data so that the rms voltmeter reads. 490 ±10mVrms. MTS VCO Adjustment 1. Keep the unit in no-signal state. 2. Connect the frequency counter to pin (39) of IC3001. 3. Connect a capacitor (100µF, 50V) in between positive(+) side of C3005 and ground. 4. Enter the service mode and select the service adjustment "M02" 5. Adjust the data so that the frequency counter reads. 62.94 ±0.75kHz. Filter Adjustment 1. Feed the following stereo pilot signal to pin (14) of IC3001 . Stereo pilot signal: 9.4kHz, 600mVrms. 2. Enter the service mode and select the service adjustment "M03". 3. Adjust the data at the point where "OK" appears on the screen. The "OK" represents the approximate center of the adjustable range of the data. Separation Adjustment 1. Connect the rms voltmeter to pin (39) of IC3001. 2. Receive the following composite stereo signal 1. Composite stereo signal: 30% modulation, left channel only, noise reduction on, 300Hz 3. Enter the service mode and select the service adjustment "M04". 4. Adjust the data until the AC voltage reading of the rms voltmeter is minimum. 5. Receive the following composite stereo signal 2. Stereo signal: 30% modulation, left channel only, noise reduction on, 3kHz 6. Enter the service mode and select the service adjustment "M05". 7. Adjust the data until the AC voltage reading of the rms voltmeter is minimum. 8. Take the above steps 1 thru 8 again for fine adjustment. 15 25L-M100/180/S100/180 CL25M10,CL25S18 MODELS 25L-M100/180, CL25M10 CHASSIS LAYOUT PWB-B H PWB-H G PWB-A F E D C B A 1 1 2 2 3 4 3 5 64 16 7 5 8 9 6 10 25L-M100/180/S100/180 CL25M10,CL25S18 MODELS 25L-S100/180, CL25S18 CHASSIS LAYOUT PWB-B H PWB-H G PWB-A F E D C B A 10 11 1 12 2 13 143 15 17 4 16 17 5 18 6 19 25L-M100/180/S100/180 CL25M10,CL25S18 MODELS 25L-M100/180, CL25M10 BLOCK DIAGRAM H G F E D C B A 1 1 2 2 3 4 3 5 64 18 7 5 8 9 6 10 25L-M100/180/S100/180 CL25M10,CL25S18 MODELS 25L-S100/180, CL25S18 BLOCK DIAGRAM H G F E D C B A 10 11 1 12 2 13 143 15 19 4 16 17 5 18 6 19 25L-M100/180/S100/180 CL25M10,CL25S18 DESCRIPTION OF SCHEMATIC DIAGRAM WAVEFORM MEASUREMENT CONDITIONS: 1. Photographs taken on a standard gated color bar signal, the tint setting adjusted for proper color. The wave shapes at the red, green and blue cathodes of the picture tube depend on the tint, color level and picture control. 2. indicates waveform check points (See chart, waveforms are measured from point indicated to chassis ground.) NOTES: H 1. The unit of resistance "ohm" is omitted. (K=kΩ=1000Ω, M=MΩ) 2. All resistors are 1/16 watt, unless otherwise noted. 3. All capacitors are µ F, unless otherwise noted. (P=pF=µµF) 4. (G) indicates ±2% tolerance may be used. 5. indicates line isolated ground. G 6. indicates hot ground. å AND SHADED ( VOLTAGE MEASUREMENT CONDITIONS: 1. All DC voltages are measured with DVM connected between points indicated and chassis ground, line voltage set at 120V AC and all controls set for normal picture unless otherwise indicated. 2. F All voltages measured with 1000µ V B & W or Color signal. ) COMPONENTS = SAFETY RELATED PARTS. ' MARK= X-RAY RELATED PARTS. DRGANNES MARQUES å ET HACHRES ( ): PIECES RELATIVES A LA SECURITE. MARQUE ' : PIECS RELATIVE AUX RAYONS X. This circuit diagram is a standard one, printed circuits may be subject to change for product improvement without prior notice. E WAVEFORMS D C B A 1 2 3 4 5 6 20 7 8 9 10 25L-M100/180/S100/180 CL25M10,CL25S18 SCHEMATIC DIAGRAM: CRT and FRONT AV Unit H G F E D Ë 25L-M100/180, CL25M10 Ë 25L-S100/180, CL25S10 C B A 10 11 1 12 2 13 143 15 21 4 16 17 5 18 6 19 25L-M100/180/S100/180 CL25M10,CL25S18 MODELS 25L-M100, CL25M10 SCHEMATIC DIAGRAM: MAIN-1 Unit H G F E D C B A 1 2 3 4 5 6 22 7 8 9 10 25L-M100/180/S100/180 CL25M10,CL25S18 10 11 12 13 14 15 23 16 17 18 19 25L-M100/180/S100/180 CL25M10,CL25S18 MODELS 25L-M100, CL25M10 SCHEMATIC DIAGRAM: MAIN-2 Unit H G F E D C B A 1 2 3 4 5 6 24 7 8 9 10 25L-M100/180/S100/180 CL25M10,CL25S18 10 11 12 13 14 15 25 16 17 18 19 25L-M100/180/S100/180 CL25M10,CL25S18 MODELS 25L-M180 SCHEMATIC DIAGRAM: MAIN-1 Unit H G F E D C B A 1 2 3 4 5 6 26 7 8 9 10 25L-M100/180/S100/180 CL25M10,CL25S18 10 11 12 13 14 15 27 16 17 18 19 25L-M100/180/S100/180 CL25M10,CL25S18 MODELS 25L-M180 SCHEMATIC DIAGRAM: MAIN-2 Unit H G F E D C B A 1 2 3 4 5 6 28 7 8 9 10 25L-M100/180/S100/180 CL25M10,CL25S18 10 11 12 13 14 15 29 16 17 18 19 25L-M100/180/S100/180 CL25M10,CL25S18 MODELS 25L-S100 SCHEMATIC DIAGRAM: MAIN-1 Unit H G F E D C B A 1 2 3 4 5 6 30 7 8 9 10 25L-M100/180/S100/180 CL25M10,CL25S18 10 11 12 13 14 15 31 16 17 18 19 25L-M100/180/S100/180 CL25M10,CL25S18 MODELS 25L-S100 SCHEMATIC DIAGRAM: MAIN-2 Unit H G F E D C B A 1 2 3 4 5 6 32 7 8 9 10 25L-M100/180/S100/180 CL25M10,CL25S18 10 11 12 13 14 15 33 16 17 18 19 25L-M100/180/S100/180 CL25M10,CL25S18 MODELS 25L-S180, CL25S18 SCHEMATIC DIAGRAM: MAIN-1 Unit H G F E D C B A 1 2 3 4 5 6 34 7 8 9 10 25L-M100/180/S100/180 CL25M10,CL25S18 10 11 12 13 14 15 35 16 17 18 19 25L-M100/180/S100/180 CL25M10,CL25S18 MODELS 25L-S180, CL25S18 SCHEMATIC DIAGRAM: MAIN-2 Unit H G F E D C B A 1 2 3 4 5 6 36 7 8 9 10 25L-M100/180/S100/180 CL25M10,CL25S18 10 11 12 13 14 15 37 16 17 18 19 25L-M100/180/S100/180 CL25M10,CL25S18 PRINTED WIRING BOARD ASSEMBLIES H G F E D C B A PWB-A: MAIN Unit (Wiring Side) 1 1 2 2 3 4 3 5 64 38 7 5 8 9 6 10 25L-M100/180/S100/180 CL25M10,CL25S18 H G F E D C B A 10 PWB-A: MAIN Unit (Chip Parts Side) 11 1 12 2 13 143 15 39 4 16 17 5 18 6 19 25L-M100/180/S100/180 CL25M10,CL25S18 H G F E PWB-B: CRT Unit (Wiring Side) D C B PWB-H: FRONT AV Unit (Wiring Side) A 1 1 2 2 3 4 3 5 64 40 7 5 8 9 6 10 25L-M100/180/S100/180 CL25M10,CL25S18 Ref. No. PARTS LIST Part No. ★ Description LISTE DES PIECES Code Ref. No. Part No. ★ Description Code PARTS REPLACEMENT CHANGE DES PIECES Replacement parts which have these special safety characteristics identified in this manual; electrical components having such features are identified by å and shaded areas in the Replacement Parts Lists and Schematic Diagrams. The use of a substitute replacement part which dose no have the same safety characteristic as the factory recommended replacement parts shown in this service manual may create shock, fire or other hazards. Les pi`eces de rechange qui pr élelesentent ces caract éleristiques sp éleciales de s élecurit éle, sont identifi élees dans ce manuel : les pi`eces élelectriques qui pr élesentent ces particularit éles, sont rep éler élee par la marque å et sont hachur élees dans les listes de pi`eces et dans les diagrammes sch élematiques. La substitution d'une pi`ece de rechange par une autre qui ne pr éLesente pas les m éoemes caract éLeristiques de s élecurit éle que la pi`ece recommand élee parl'usine et dans ce manuel de service, peut provoquer une éLelectrocution, un incendie ou toutautre sinistre. "HOW TO ORDER REPLACEMENT PARTS" To have your order filled promptly and correctly, please furnish the following informations. 1. MODEL NUMBER 2. REF. NO. 3. PART NO. 4. DESCRIPTION in USA: "COMMENT COMMANDER LES PIECES DE RECHANGE" Pour que votre commande soit rapidement et correctement remplie, veuillez fournir les renseignements suivants. Contact your nearest SHARP Parts Distributor to order. For location of SHARP Parts Distributor, Please call TollFree; 1-800-BE-SHARP Ref. No. ★ Description ç V101 VB63AFW32X/*S or VB63AHC26X/*S çå DY601 RCiLH0117MEZZ or RCiLH0118MEZZ å L702 RCiLG0036MEZZ MSPRT0002MEZZ PMAGF3003CEZZ QEARC2508MEZZ M Picture Tube CK M Deflection Yoke BA M M M M BB AA AK AF Degaussing Coil Spring for CRT Magnet Ass'y Grounding Part MARQUE : PIECES RELATIVE AUX RAYONS X Ref. No. Code Part No. PWB-A: PWB-A: PWB-A: PWB-A: PICTURE TUBE çå 4. DESCRIPTION ★MARQUE: SECTION LIVRAISON DES PIECES DE RECHANGE MARK : X- RAY RELATED PARTS Part No. 2. NO. DE REF 3. NO. DE PIECE in CANADA: Contact SHARP Electronics of Conada Limited Phone (416) 890-2100 ★MARK: SPARE PARTS-DELIVERY SECTION ç 1. NUMERO DU MODELE Description Code DUNTK9806WEK0 (25L-M100/CL25M10) DUNTK9806WEK1 (25L-M180) DUNTK9806WEK2 (25L-S100) DUNTK9806WEK3 (25L-S180/CL25S18) MAIN UNIT TUNER NOTE: THE PARTS HERES SHOWN ARE SUPPLIED AS AN ASSEMBLY BUT NOT INDEPENEDENTLY. å TU51 VTU115B8035AT M VHF Tuner AU or VTUVTST5UF78/ INTEGRATED CIRCUITS IC101 VHiKA78S05P-1 çå IC201 RH-iX3253CEZZ IC351 VHiAN7511//-1 IC352 IC501 IC701 å IC702 å IC703 å IC750 å IC751 IC951 å å PRINTED WIRING BOARD ASSEMBLIES (NOT REPLACEMENT ITEM) PWB-A DUNTK9806WEK0 – MAIN Unit (25L-M100, CL25M10) PWB-A DUNTK9806WEK1 – MAIN Unit (25L-M180) PWB-A DUNTK9806WEK2 – MAIN Unit (25L-S100) PWB-A DUNTK9806WEK3 – MAIN Unit (25L-S180, CL25S18) PWB-B DUNTK9510WEK1 – CRT Unit PWB-H DUNTK9310WEK0 – FRONT AV Unit (25L-M100/180, CL25M10) PWB-H DUNTK9310WEK1 – FRONT AV Unit (25L-S100/180, CL25S18) ★ — IC2001 IC2040 IC2101 IC3001 — — — — — VHiAN7511//-1 VHiTA8403K/-1 VHiSTRF66261E RH-FX0034CEZZ VHiSE120N//-1 VHiKA7809Pi-1 VHiKA7809Pi-1 VHiMM1111XF1E RH-iX3256CEZZ VHiKiA7045P-1 VHiM24C01B/-1 VHiCXA2074Q-1 J KA78S05P J TA1268AN J I.C. (25L-S100/180, CL25S18) J I.C. J TA8403K J STR-F6626 J PC817 J SE120N M KA7809PI M KA7809PI J MM1111XFBE (25L-S100/180, CL25S18) J TMPA8701CMF142 J KIA7045P J M24C01-BN6 J CXA2074Q (25L-S100/180, CL25S18) AD AV AK AK AL AX AE AG AE AE AE AX AD AF AY TRANSISTORS — You can substitute "VS2SD601AR/-1" for "VS2SC2412-C-1". Q201 VS2SC2735//1E J 2SC2735 AC Q301 VS2SD601AR/-1 J 2SD601AR AC (25L-S100/180, CL25S18) Q401 VS2SD601AR/-1 J 2SD601AR AC Q402 VS2SB709AR/-1 J 2SB709AR AC Q403 VS2SD601AR/-1 J 2SD601AR AC Q421 VS2SB709AR/-1 J 2SB709AR AC Q451 VS2SB709AR/-1 J 2SB709AR AC 41 25L-M100/180/S100/180 CL25M10,CL25S18 Ref. No. Part No. PWB-A: PWB-A: PWB-A: PWB-A: å ★ Description Code Ref. No. DUNTK9806WEK0 (25L-M100/CL25M10) DUNTK9806WEK1 (25L-M180) DUNTK9806WEK2 (25L-S100) DUNTK9806WEK3 (25L-S180/CL25S18) MAIN UNIT (Continued) Q601 Q602 Q751 Q901 VS2SC2482//-1 VS2SD2539//1E VS2SC3198-Y-1 VS2SD601AR/-1 J J J J Q902 VS2SD601AR/-1 J Q903 VS2SD601AR/-1 J Q904 VS2SD601AR/-1 J Q2060 VS2SD601AR/-1 Q2201 VS2SD601AR/-1 Q2211 VS2SD601AR/-1 J J J 2SC2482 2SD2539 2SC3198 (Y) 2SD601AR (25L-S180, CL25S18) 2SD601AR (25L-S180, CL25S18) 2SD601AR (25L-S180, CL25S18) 2SD601AR (25L-S180, CL25S18) 2SD601AR 2SD601AR 2SD601AR AD AP AA AC Code J J J J J Ceramic Filter Ceramic Filter Ceramic Filter Ceramic Filter SAW Filter AD AE AD AD AH COILS L201 L202 L301 L302 L401 L402 L403 L404 L421 L672 å L701 L702 L705 L729 L2040 AC AC AC AC AC AC DIODES VP-XF1R2K0000 RCiLi0588CEZZ VP-XF8R2K0000 RCiLi0613CEZZ VP-XF6R8K0000 VP-XF3R3K0000 VP-XF8R2K0000 VP-XF8R2K0000 VP-XF680K0000 RCiLZ0101MEZZ RCiLF0025PEZZ RCiLF0025PEZZ RCiLP0179CEZZ RCiLP0179CEZZ RCiLB0159CEZZ J J J J J J J J J M M M J J J Peaking 1.2µH VCO Coil Peaking 8.2µH IF Coil Peaking 6.8µH Peaking 3.3µH Peaking 8.2µH Peaking 8.2µH Peaking 68µH Coil Coil Coil Coil Coil Oscillation Coil AB AF AB AE AB AB AB AB AB AE AK AK AD AD AE TRANSFORMERS T601 çå T602 å T701 å T702 RTRNZ0057PEZZ R Transformer RTRNF0037MEZZ M H-Volt Transformer RTRNP0543CEZZ J Power Transformer RTRNZ0017MEZZ M Transformer AK AY AM BC CAPACITORS [EL.··· Electrolytic, M-Poly.··· Metalized Polypro Film] C51 VCEA0A1CW476M J 47 16V EL. C53 VCEA0A1HW105M J 1.0 50V EL. C54 VCEA0A1HW475M J 4.7 50V EL. C55 VCEA0A1CW108M J 1000 16V EL. C103 VCEA0A1CW107M J 100 16V EL. (25L-M100, CL25M10) C103 VCEA0A1CW228M J 2200 16V EL. (25L-M180, 25L-S100/180, CL25S18) C201 VCKYMN1HB102K J 1000p 50V Ceramic C202 VCKYCY1HF103Z J 0.01 50V Ceramic C203 VCKYCY1HB102K J 1000p 50V Ceramic C204 VCKYCY1HF103Z J 0.01 50V Ceramic C205 VCEA0A1HW474M J 0.47 50V EL. C206 VCEA0A1CW337M J 330 16V EL. C207 VCKYCY1HF103Z J 0.01 50V Ceramic C208 VCEA0A1HW474M J 0.47 50V EL. C209 VCKYCY1HB222K J 2200p 50V Ceramic C210 VCKYCY1HB102K J 1000p 50V Ceramic C301 VCCCCY1HH330J J 33p 50V Ceramic C302 VCCCCY1HH151J J 150p 50V Ceramic C303 VCCCCY1HH390J J 39p 50V Ceramic (25L-S100/180, CL25S18) C303 VCKYCY1HB472K J 4700p 50V Ceramic (25L-M100/180, CL25M10) C304 VCEA0A1HW225M J 2.2 50V EL. (25L-M100/180, CL25M10) C307 VCCCCY1HH1R5C J 1.5p 50V Ceramic C308 VCKYCY1HB102K J 1000p 50V Ceramic C309 VCEA0A1CW337M J 330 16V EL. C313 VCEA0A1CW476M J 47 16V EL. C351 VCEA0A1HW106M J 10 50V EL. (25L-S100/180, CL25S18) C352 VCKYCY1HB332K J 3300p 50V Ceramic (25L-S100/180, CL25S18) C354 VCEA0A1HW106M J 10 50V EL. (25L-S100/180, CL25S18) C355 VCKYCY1HB332K J 3300p 50V Ceramic C356 VCEA0A1HW106M J 10 50V EL. C358 VCEA0A1CW477M J 470 16V EL. C359 VCEA0A1HW106M J 10 50V EL. C401 VCKYCY1HB331K J 330p 50V Ceramic PACKAGED CIRCUITS PR701 RMPTP0092CEZZ J Packaged Circuit X801 RCRSB0205CEZZ J Crystal or RCRSB0001PEZZ Description FILTERS CF301 RFiLC0029TAZZ CF401 RFiLC0013CEZZ CF631 RFiLA0034CEZZ CF2040 RFiLC0121GEZZ SF201 RFiLC0405CEZZ You can substitute "VHD1SS119//-1" for "RH-DX0475CEZZ". D51 RH-EX0611GEZZ J Zener Diode, 5.1V AA D52 RH-EX0673GEZZ J Zener Diode, 32V AB D53 RH-EX0611GEZZ J Zener Diode, 5.1V AA D103 VHD1SS119//-1 J Diode AB (25L-M180, 25L-S100/180, CL25S18) D401 VHD1SS119//-1 J Diode AB D402 RH-EX0604GEZZ J Zener Diode, 3.9V AB D454 RH-EX0611GEZZ J Zener Diode, 5.1V AA D455 VHD1SS119//-1 J Diode AB D456 VHD1SS119//-1 J Diode AB D457 RH-EX0217CEZZ J Zener Diode AB D458 RH-EX0217CEZZ J Zener Diode AB D459 VHD1SS119//-1 J Diode AB å D501 RH-DX0131CEZZ J Diode AC å D510 RH-DX0441CEZZ J Diode AC D621 RH-EX0631GEZZ J Zener Diode, 9.1V AA D622 RH-DX0131CEZZ J Diode AC çå D651 RH-DX0131CEZZ J Diode AC çå D652 RH-EX1313CEZZ M Zener Diode, 9.1V AB çå D653 VHD1SS119//-1 J Diode AB çå D654 VHD1SS119//-1 J Diode AB å D701 RH-DX0154CEZZ J Diode AC å D702 RH-DX0154CEZZ J Diode AC å D703 RH-DX0154CEZZ J Diode AC å D704 RH-DX0154CEZZ J Diode AC D705 VHD1SS82///1A J Diode AC D706 RH-DX0066GEZZ J Diode AB D707 VHD1SS82///1A J Diode AC D708 RH-DX0066GEZZ J Diode AB å D709 RH-DX0229CEZZ J Diode AF å D712 RH-DX0407CEZZ J Diode AD D713 RH-EX0673GEZZ J Zener Diode, 32V AB D715 RH-EX0610GEZZ J Zener Diode AA D716 VHD1SS119//-1 J Diode AB D717 RH-EX0650GEZZ J Zener Diode, 16V AB å D725 RH-DX0407CEZZ J Diode AD å D751 RH-DX0441CEZZ J Diode AC å D752 RH-DX0441CEZZ J Diode AC å D753 RH-DX0441CEZZ J Diode AC å D754 RH-DX0441CEZZ J Diode AC D755 VHD1SS119//-1 J Diode AB å D756 RH-DX0441CEZZ J Diode AC D2001 VHD1SS119//-1 J Diode AB å ★ Part No. AH AF 42 AB AB AB AD AC AB AA AA AA AA AB AC AA AB AA AA AA AA AA AA AB AD AA AC AB AB AA AB AA AB AC AB AA 25L-M100/180/S100/180 CL25M10,CL25S18 Ref. No. Part No. PWB-A: PWB-A: PWB-A: PWB-A: C402 C403 C404 C405 C406 C408 C409 C410 C411 C412 C413 C414 C421 C422 C451 C452 C453 C501 C502 C510 C511 C512 C513 C514 C515 C516 C517 C518 C551 C552 C606 C607 çå C610 çå C611 C615 C623 C631 C632 C633 C652 C653 C680 C682 å C701 C702 C703 å C705 å C706 C707 C708 C709 C710 C717 C718 C722 å C723 å C725 C726 C727 C729 å C730 å C731 C732 C741 C742 C753 C755 ★ Description Code Ref. No. DUNTK9806WEK0 (25L-M100/CL25M10) DUNTK9806WEK1 (25L-M180) DUNTK9806WEK2 (25L-S100) DUNTK9806WEK3 (25L-S180/CL25S18) MAIN UNIT (Continued) VCCCCY1HH101J VCKYCY1CB104K VCEA0A1HW106M VCEA0A1HW335M VCEA0A1HW225M VCEA0A1HW106M VCEA0A1HW105M RC-QZA104TAYK VCEA0A1CW337M VCKYCY1HB103K VCKYCY1HB103K VCKYCY1CB104K VCCCCY1HH330J VCEA0A1CW476M RC-QZA104TAYK VCEA0A1HW475M VCEA0A1CW226M VCKYPA2HB102K VCEA0A1VW108M VCFYSA1JA564J VCKYPA2HB391K RC-QZA473TAYK RC-QZA103TAYK VCEA0A1VW107M VCEA0A1HW105M VCEACA1HC105K VCEA0A1VW108M VCFYSA1JA473J VCSATA1CE225K VCEA0A1HW225M VCKYPA2HB561K VCKYPA1HB472K VCFPVC3CA722H VCFPVC3CA722H VCKYPA2HB102K VCEA4A2EN106M VCEA0A1HW335M RC-QZA103TAYK VCEA0A1CW477M VCEA0A1HW106M VCEA0A1HW106M VCFPVC2DB564J VCKYPA2HB331K RC-FZ017SCEZZ or RC-FZ012SGEZZ RC-KZ0029CEZZ RC-KZ0029CEZZ RC-EZ0800CEZZ RC-KZ0092GEZZ VCFPVC3CA222H VCCSPA1HL471J VCEA0A1VW107M RC-QZA102TAYJ VCKYPA2HB472K VCKYPA2HB472K RC-QZA104TAYK RC-EZ0724CEZZ RC-EZ0809CEZZ RC-KZ0338CEZZ RC-KZ0338CEZZ VCEA0A1CW106M RC-EZ0385CEZZ RC-EZ0385CEZZ VCKYPA2HB102K VCKYPA2HB102K VCKYPA2HB102K VCEA0A1CW107M VCEA0A1CW476M J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 100p 0.1 10 3.3 2.2 10 1.0 0.1 330 0.01 0.01 0.1 33p 47 0.1 4.7 22 1000p 1000 0.56 390p 0.047 0.01 100 1.0 1.0 1000 0.047 2.2 2.2 560p 4700p 7200p 7200p 1000p 10 3.3 0.01 470 10 10 0.56 330p 0.22 50V Ceramic 16V Ceramic 50V EL. 50V EL. 50V EL. 50V EL. 50V EL. 50V Mylar 16V EL. 50V Ceramic 50V Ceramic 16V Ceramic 50V Ceramic 16V EL. 50V Mylar 50V EL. 16V EL. 500V Ceramic 35V EL. 63 Mylar 500V Ceramic 50V Mylar 50V Mylar 35V EL. 50V EL. 50V EL. 35V EL. 63 Mylar 16V Tantalum 50V EL. 500V Ceramic 50V Ceramic 1.6kV M-Poly. 1.6kV M-Poly. 500V Ceramic 250V EL. 50V EL. 50V Mylar 16V EL. 50V EL. 50V EL. 200V M-Poly. 500V Ceramic AC250V Plastic J J J J J J J J J J J J J J J J J J J J J J J 0.01 AC250V Ceramic 0.01 AC250V Ceramic 560 200V EL. 0.0033 AC250V Ceramic 2200p 1.6kV M-Poly. 470p 50V Ceramic 100 35V EL. 1000p Mylar 4700p 500V Ceramic 4700p 500V Ceramic 0.1 50V Mylar 100 160V EL. 220 160V EL. Capacitor Capacitor 10 16V EL. 1000 16V EL. 1000 16V EL. 1000p 500V Ceramic 1000p 500V Ceramic 1000p 500V Ceramic 100 16V EL. 47 16V EL. AA AB AB AB AB AB AB AB AC AA AA AB AA AB AB AB AB AA AD AE AA AB AA AC AB AC AD AC AB AB AA AA AF AF AA AD AB AA AC AB AB AF AA AD Part No. ★ Description Code J J J J J J J J J J 470 35V EL. 0.022 50V Mylar 0.47 50V EL. 11p 50V Ceramic 0.1 16V Ceramic 0.1 16V Ceramic 0.1 16V Ceramic 220p 50V Ceramic 1000p 50V Ceramic 3.3 50V EL. (25L-S180, CL25S18) 47 16V EL. (25L-S180, CL25S18) 3.3 50V EL. (25L-S180, CL25S18) 2.2 50V EL. (25L-S100/180, CL25S18) 2.2 50V EL. 680p 50V Ceramic (25L-S180, CL25S18) 680p 50V Ceramic (25L-S180, CL25S18) 3.3 50V EL. (25L-S180, CL25S18) 3.3 50V EL. (25L-S180, CL25S18) 0.018 25V Ceramic (25L-S180, CL25S18) 0.018 25V Ceramic (25L-S180, CL25S18) 10 50V EL. (25L-S100/180, CL25S18) 10 50V EL. (25L-S100/180, CL25S18) 0.01 50V Ceramic (25L-S100/180, CL25S18) 10 16V EL. (25L-S100/180, CL25S18) 100p 50V Ceramic 100p 50V Ceramic 100 10V EL. 1.0 50V EL. 0.1 16V Ceramic 100p 50V Ceramic 100 10V EL. 680p 50V Ceramic 39p 50V Ceramic 4.7 50V EL. 100p 50V Ceramic 4.7 50V EL. (N.P) (25L-S100/180, CL25S18) 5600p 50V Ceramic (25L-S100/180, CL25S18) 0.012 Mylar (25L-S100/180, CL25S18) 1.0 50V EL. (25L-S100/180, CL25S18) 4.7 50V EL. (25L-S100/180, CL25S18) 10 50V EL. (25L-S100/180, CL25S18) 4.7 50V EL. (25L-S100/180, CL25S18) 0.01 50V Ceramic (25L-S100/180, CL25S18) 220 16V EL. (25L-S100/180, CL25S18) 4.7 50V EL. (N.P) (25L-S100/180, CL25S18) 4.7 50V EL. (25L-S100/180, CL25S18) 4.7 50V EL. (N.P) (25L-S100/180, CL25S18) 2700p 50V Ceramic (25L-S100/180, CL25S18) AB AB AB AA AB AB AB AA AA AB C772 C801 C802 C803 C804 C805 C806 C807 C808 C901 VCEA0A1VW477M RC-QZA223TAYK VCEA0A1HW474M VCCCCY1HH110J VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCCCCY1HH221J VCKYCY1HB102K VCEA0A1HW335M C902 VCEA0A1CW476M J C903 VCEA0A1HW335M J C908 VCEA0A1HW225M J C909 C910 VCEA0A1HW225M J VCKYCY1HB681K J C911 VCKYCY1HB681K J C922 VCEA0A1HW335M J C923 VCEA0A1HW335M J C931 VCKYCY1EB183K J C932 VCKYCY1EB183K J C951 VCEA0A1HW106M J C952 VCEA0A1HW106M J C954 VCKYCY1HF103Z C955 VCEA0A1CW106M J C2001 C2002 C2040 C2041 C2060 C2061 C2062 C2201 C2202 C2601 C2602 C3001 VCCCCY1HH101J VCCCCY1HH101J VCEA0A1AW107M VCEA0A1HW105M VCKYCY1CB104K VCCCCY1HH101J VCEA0A1AW107M VCKYCY1HB681K VCCCCY1HH390J VCEA0A1HW475M VCCCCY1HH101J VCE9GA1HW475M J J J J J J J J J J J J J C3002 VCKYCY1HB562K J AC AC AQ AC AE AA AC AB AB AB AB AG AL AD AD AB AE AE AA AA AA AC AB C3003 RC-QZA123TAYK J C3004 VCEA0A1HW105M J C3005 VCEA0A1HW475M J C3006 VCEA0A1HW106M J C3007 VCEA0A1HW475M J C3008 VCKYCY1HF103Z J C3009 VCEA0A1CW227M J C3010 VCE9GA1HW475M J C3011 VCEA0A1HW475M J C3012 VCE9GA1HW475M J C3013 VCKYCY1HB272K J 43 AB AB AB AB AA AA AB AB AA AA AB AB AA AB AA AA AB AB AB AA AB AA AA AB AA AB AA AB AB AB AB AB AA AC AB AB AB AA 25L-M100/180/S100/180 CL25M10,CL25S18 Ref. No. ★ Part No. PWB-A: PWB-A: PWB-A: PWB-A: Description Code Ref. No. DUNTK9806WEK0 (25L-M100/CL25M10) DUNTK9806WEK1 (25L-M180) DUNTK9806WEK2 (25L-S100) DUNTK9806WEK3 (25L-S180/CL25S18) MAIN UNIT (Continued) C3014 RC-QZA473TAYK C3015 VCSATA1CE335K C3016 VCE9GA1HW475M C3017 VCSATA1CE106K C3018 VCEA0A1HW105M C3019 VCEA0A1HW475M C3020 VCEA0A1HW475M C3021 VCEA0A1HW475M C3022 VCEA0A1HW475M J 0.047 Mylar (25L-S100/180, CL25S18) J 3.3 16V Tantalum (25L-S100/180, CL25S18) J 4.7 50V EL. (N.P) (25L-S100/180, CL25S18) J 10 16V Tantalum (25L-S100/180, CL25S18) J 1.0 50V EL. (25L-S100/180, CL25S18) J 4.7 50V EL. (25L-S100/180, CL25S18) J 4.7 50V EL. J 4.7 50V EL. (25L-S100/180, CL25S18) J 4.7 50V EL. (25L-S100/180, CL25S18) RJ60 RJ61 RJ63 RJ64 RJ67 å R51 å R52 å R53 R54 R55 R56 R57 R201 R202 R203 R204 R205 R206 R207 R208 R301 R302 R303 AB AC AB AD AB AB AB AB AB R303 RESISTORS RJ1 RJ5 RJ6 RJ9 RJ10 RJ11 RJ12 RJ13 RJ14 RJ15 RJ16 RJ17 RJ18 RJ19 RJ20 RJ21 RJ22 RJ25 RJ26 RJ28 RJ29 RJ30 RJ31 RJ32 RJ35 RJ36 RJ37 RJ38 RJ39 RJ40 RJ41 RJ42 RJ43 RJ46 RJ48 RJ49 RJ50 RJ51 RJ52 RJ54 RJ55 RJ57 RJ58 [M-Ox.··· Metal Oxide.] VRD-MN2BE000J J 0 1/8W Carbon VRD-MN2BE000J J 0 1/8W Carbon (25L-M100/180, CL25M10) VRD-MN2BE000J J 0 1/8W Carbon (25L-M100/180, CL25M10) VRD-MN2BE000J J 0 1/8W Carbon VRD-MN2BE000J J 0 1/8W Carbon VRS-CY1JF000J J 0 1/16W M-Ox. VRD-MN2BE000J J 0 1/8W Carbon VRD-MN2BE000J J 0 1/8W Carbon VRD-MN2BE000J J 0 1/8W Carbon (25L-S100/180, CL25S18) VRS-CY1JF000J J 0 1/16W M-Ox. VRS-CY1JF000J J 0 1/16W M-Ox. VRD-MN2BE000J J 0 1/8W Carbon VRS-CY1JF000J J 0 1/16W M-Ox. (25L-M100/180, CL25M10) VRD-MN2BE000J J 0 1/8W Carbon VRD-MN2BE000J J 0 1/8W Carbon VRD-MN2BE000J J 0 1/8W Carbon VRD-MN2BE000J J 0 1/8W Carbon VRD-MN2BE000J J 0 1/8W Carbon VRS-CY1JF000J J 0 1/16W M-Ox. VRD-MN2BE000J J 0 1/8W Carbon VRD-MN2BE000J J 0 1/8W Carbon VRS-CY1JF000J J 0 1/16W M-Ox. VRS-CY1JF000J J 0 1/16W M-Ox. VRS-CY1JF000J J 0 1/16W M-Ox. (25L-M180, 25L-S100/180, CL25S18) VRS-CY1JF000J J 0 1/16W M-Ox. VRS-CY1JF000J J 0 1/16W M-Ox. VRS-CY1JF000J J 0 1/16W M-Ox. VRS-CY1JF000J J 0 1/16W M-Ox. VRD-MN2BE000J J 0 1/8W Carbon VRD-MN2BE000J J 0 1/8W Carbon VRD-MN2BE000J J 0 1/8W Carbon VRS-CY1JF000J J 0 1/16W M-Ox. VRD-MN2BE000J J 0 1/8W Carbon VRS-CY1JF000J J 0 1/16W M-Ox. VRD-MN2BE000J J 0 1/8W Carbon VRD-MN2BE000J J 0 1/8W Carbon VRD-MN2BE000J J 0 1/8W Carbon VRD-MN2BE000J J 0 1/8W Carbon VRS-CY1JF000J J 0 1/16W M-Ox. VRD-MN2BE000J J 0 1/8W Carbon VRS-CY1JF000J J 0 1/16W M-Ox. VRD-MN2BE000J J 0 1/8W Carbon VRD-MN2BE000J J 0 1/8W Carbon R304 AA AA R305 AA R306 AA AA AA AA AA AA R351 R352 R353 R354 AA AA AA AA R355 R356 R357 R358 R401 R402 R403 R404 R405 R406 R407 R408 R409 R410 R411 R412 R413 R414 R415 R421 R422 R423 R424 å R451 R452 R453 R454 R456 R458 å R501 R510 R511 R512 R513 R514 AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 44 Part No. ★ Description VRD-MN2BE000J J 0 1/8W Carbon VRS-CY1JF000J J 0 1/16W M-Ox. VRD-MN2BE000J J 0 1/8W Carbon VRD-MN2BE000J J 0 1/8W Carbon VRS-CY1JF000J J 0 1/16W M-Ox. VRS-RG3AB151J M 150 1W M-Ox. VRS-RG3DB123J J 12k 2W M-Ox. VRS-RG3AB470J J 47 1W M-Ox. VRD-MN2BE101J J 100 1/8W Carbon VRD-MN2BE101J J 100 1/8W Carbon VRD-MN2BE823J J 82k 1/8W Carbon VRD-MN2BE392J J 3.9k 1/8W Carbon VRD-MN2BE151J J 150 1/8W Carbon VRD-MN2BE122J J 1.2k 1/8W Carbon VRD-MN2BE682J J 6.8k 1/8W Carbon VRD-MN2BE270J J 27 1/8W Carbon VRS-CY1JF331J J 330 1/16W M-Ox. VRD-MN2BE121J J 120 1/8W Carbon VRD-MN2BE4R7J J 4.7 1/8W Carbon VRD-MN2BE331J J 330 1/8W Carbon VRD-MN2BE222J J 2.2k 1/8W Carbon VRS-CY1JF102J J 1.0k 1/16W M-Ox. VRD-MN2BE103J J 10k 1/8W Carbon (25L-S100/180, CL25S18) VRD-MN2BE153J J 15k 1/8W Carbon (25L-M100/180, CL25M10) VRD-MN2BE333J J 33k 1/8W Carbon (25L-S100/180, CL25S18) VRD-MN2BE102J J 1.0k 1/8W Carbon (25L-S100/180, CL25S18) VRD-MN2BE152J J 1.5k 1/8W Carbon (25L-S100/180, CL25S18) VRD-MN2BE683J J 68k 1/8W Carbon (25L-S100/180, CL25S18) VRD-MN2BE103J J 10k 1/8W Carbon (25L-S100/180, CL25S18) VRD-RA2BE822J J 8.2k 1/8W Carbon (25L-S100/180, CL25S18) VRD-MN2BE223J J 22k 1/8W Carbon (25L-S100/180, CL25S18) VRD-MN2BE683J J 68k 1/8W Carbon VRD-MN2BE103J J 10k 1/8W Carbon VRD-MN2BE822J J 8.2k 1/8W Carbon VRD-MN2BE223J J 22k 1/8W Carbon VRS-CY1JF682J J 6.8k 1/16W M-Ox. VRS-CY1JF331J J 330 1/16W M-Ox. VRS-CY1JF391J J 390 1/16W M-Ox. VRD-MN2BE102J J 1.0k 1/8W Carbon VRS-CY1JF470J J 47 1/16W M-Ox. VRS-CY1JF680J J 68 1/16W M-Ox. VRS-CY1JF102J J 1.0k 1/16W M-Ox. VRS-CY1JF471J J 470 1/16W M-Ox. VRD-MN2BE562J J 5.6k 1/8W Carbon VRD-RA2BE124J J 120k 1/8W Carbon VRD-MN2BE153J J 15k 1/8W Carbon VRD-RA2BE561J J 560 1/8W Carbon VRS-CY1JF101J J 100 1/16W M-Ox. VRS-CY1JF101J J 100 1/16W M-Ox. VRS-CY1JF101J J 100 1/16W M-Ox. VRD-MN2BE152J J 1.5k 1/8W Carbon VRS-CY1JF472J J 4.7k 1/16W M-Ox. VRS-CY1JF152J J 1.5k 1/16W M-Ox. VRS-CY1JF102J J 1.0k 1/16W M-Ox. VRS-RG2HC103J J 10k 1/2W M-Ox. VRD-RM2HD153J J 15k 1/2W Carbon VRD-RA2EE683J J 68k 1/4W Carbon VRD-MN2BE102J J 1.0k 1/8W Carbon VRD-MN2BE682J J 6.8k 1/8W Carbon VRD-MN2BE152J J 1.5k 1/8W Carbon VRN-RL3ABR56J J 0.56 1W Metal Film VRD-MN2BE471J J 470 1/8W Carbon VRD-RA2BE104G J 100k 1/8W Carbon VRD-RA2BE124G J 120k 1/8W Carbon VRD-RA2BE473J J 47k 1/8W Carbon VRD-MN2BE101J J 100 1/8W Carbon Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 25L-M100/180/S100/180 CL25M10,CL25S18 Ref. No. Part No. PWB-A: PWB-A: PWB-A: PWB-A: R519 R520 R523 å R524 R526 R551 R552 R553 R554 å R604 R605 R606 å R607 å R609 R610 å R611 R622 R623 R624 R625 R626 R627 R631 R632 R633 R634 çå R651 çå R652 çå R653 çå R654 çå R655 R690 å R701 å R702 R704 å R705 å R706 R707 å R709 R710 R711 å R715 å R723 R724 R725 R727 å R728 å å ★ Description Code Ref. No. DUNTK9806WEK0 (25L-M100/CL25M10) DUNTK9806WEK1 (25L-M180) DUNTK9806WEK2 (25L-S100) DUNTK9806WEK3 (25L-S180/CL25S18) MAIN UNIT (Continued) VRD-RA2BE123G VRD-MN2BE184J VRN-RL3AB1R0J VRS-RG3AB391J VRD-MN2BE332J VRS-CY1JF472J VRS-CY1JF102J VRD-MN2BE223J VRD-MN2BE184J VRS-RG3LB392J VRD-RA2BE331J VRD-RA2BE331J VRS-RG3LB392J VRS-RG3AB562J VRD-RM2HD220J VRS-KA3NG3R3K VRN-RL3ABR33J VRN-RL3AB2R7J VRS-RG3DB332J VRD-MN2BE102J VRN-RL3AB3R3J VRD-RM2HD224J VRS-CY1JF391J VRS-CY1JF152J VRD-MN2BE472J VRD-RA2BE4R7J VRS-RG2HC270J VRN-RA2BK103F VRN-RA2BK822F VRD-MN2BE184J VRS-CY1JF104J VRS-RG2HC102J RR-HZ0048CEZZ VRW-KQ3NC1R2K VRD-RM2HD154J VRN-RL3DBR22J VRN-RL3DBR27J VRS-RG2HC681J VRN-GA2EB1R0J VRD-RM2HD330J VRD-RA2BE242J VRS-RG3DB153J VRN-RL3DBR39J VRS-RG2HC332J VRS-RG2HC821J VRD-RA2BE271J VRN-RL3LB4R7J J J M J J J J J J M J J M M J J M M M J M J J J J J M J J J J J J J J J M J J J J J M J M J M R728 VRS-RG3DB120J M R734 R737 R751 R801 R802 R803 R804 R805 R806 R807 R808 R901 VRD-RM2HD124J J VRN-RL3DBR56J M VRD-MN2BE473J J VRD-MN2BE332J J VRS-CY1JF332J J VRS-CY1JF222J J VRS-CY1JF222J J VRS-CY1JF222J J VRS-CY1JF333J J VRS-CY1JF152J J VRD-RA2BE102J J VRD-RA2BE331J J R903 VRD-MN2BE102J J R904 VRS-CY1JF683J J R905 VRS-CY1JF223J J 12k 1/8W Carbon 180k 1/8W Carbon 1.0 1W Metal Film 390 1W M-Ox. 3.3k 1/8W Carbon 4.7k 1/16W M-Ox. 1.0k 1/16W M-Ox. 22k 1/8W Carbon 180k 1/8W Carbon 3.9k 3.0W M-Ox. 330 1/8W Carbon 330 1/8W Carbon 3.9k 3.0W M-Ox. 5.6k 1W M-Ox. 22 1/2W Carbon 3.3 7.0W M-Ox. 0.33 1W Metal Film 2.7 1W Metal Film 3.3k 2W M-Ox. 1.0k 1/8W Carbon 3.3 1W Metal Film 220k 1/2W Carbon 390 1/16W M-Ox. 1.5k 1/16W M-Ox. 4.7k 1/8W Carbon 4.7 1/8W Carbon 27 1/2W M-Ox. 10k 1/8W Metal Film 8.2k 1/8W Metal Film 180k 1/8W Carbon 100k 1/16W M-Ox. 1.0k 1/2W M-Ox. 3.9M 1/2W Solid 1.2 7.0W Cement 150k 1/2W Carbon 0.22 2W Metal Film 0.27 2W Metal Film 680 1/2W M-Ox. 1.0 1/4W Metal Film 33 1/2W Carbon 2.4k 1/8W Carbon 15k 2W M-Ox. 0.39 2W Metal Film 3.3k 1/2W M-Ox. 820 1/2W M-Ox. 270 1/8W Carbon 4.7 3.0W Metal Film (25L-S100/180, CL25S18) 12 2W M-Ox. (25L-M100/180, CL25M10) 120k 1/2W Carbon 0.56 2W Metal Film 47k 1/8W Carbon 3.3k 1/8W Carbon 3.3k 1/16W M-Ox. 2.2k 1/16W M-Ox. 2.2k 1/16W M-Ox. 2.2k 1/16W M-Ox. 33k 1/16W M-Ox. 1.5k 1/16W M-Ox. 1.0k 1/8W Carbon 330 1/8W Carbon (25L-S180, CL25S18) 1.0k 1/8W Carbon (25L-S180, CL25S18) 68k 1/16W M-Ox. (25L-S180, CL25S18) 22k 1/16W M-Ox. (25L-S180, CL25S18) AA AA AA AA AA AA AA AA AA AB AA AA AB AA AA AD AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AE AA AA AA AA AA AA AA AA AA AA AA AA AB Part No. R906 VRS-CY1JF392J R907 VRS-CY1JF182J R908 VRS-CY1JF102J R910 VRD-MN2BE102J R911 VRS-CY1JF683J R912 VRS-CY1JF223J R913 VRS-CY1JF392J R914 VRS-CY1JF182J R915 VRS-CY1JF102J R922 VRS-CY1JF102J R923 VRS-CY1JF102J R924 VRD-MN2BE750J R925 VRD-MN2BE104J R926 VRD-MN2BE104J R951 VRD-RA2BE101J R952 VRD-MN2BE102J R961 R962 R2001 R2002 R2004 R2006 R2007 VRD-RA2BE101J VRD-RA2BE101J VRD-RA2BE562J VRD-MN2BE103J VRD-MN2BE101J VRS-CY1JF103J VRS-CY1JF223J R2008 R2009 R2010 R2011 VRD-MN2BE224J VRD-RA2BE102J VRD-MN2BE102J RH-EX0611GEZZ R2011 VRD-RA2BE561J R2012 VRS-CY1JF471J R2012 VRS-CY1JF561J R2020 R2024 R2025 R2026 R2027 R2028 R2029 R2030 R2032 R2035 R2040 R2041 R2042 R2043 R2044 R2045 R2046 R2047 R2048 R2060 R2061 R2062 AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 45 VRS-CY1JF223J VRD-RA2BE682J VRD-RA2BE682J VRD-RA2BE682J VRD-MN2BE682J VRD-MN2BE102J VRS-CY1JF103J VRS-CY1JF103J VRD-RA2BE103J VRD-MN2BE223J VRD-MN2BE102J VRD-MN2BE333J VRD-MN2BE101J VRS-CY1JF333J VRD-MN2BE682J VRD-MN2BE101J VRD-RA2BE101J VRS-CY1JF221J VRS-CY1JF562J VRD-MN2BE221J VRD-MN2BE562J VRD-MN2BE183J ★ Description J 3.9k 1/16W M-Ox. (25L-S180, CL25S18) J 1.8k 1/16W M-Ox. (25L-S180, CL25S18) J 1.0k 1/16W M-Ox. (25L-S180, CL25S18) J 1.0k 1/8W Carbon (25L-S180, CL25S18) J 68k 1/16W M-Ox. (25L-S180, CL25S18) J 22k 1/16W M-Ox. (25L-S180, CL25S18) J 3.9k 1/16W M-Ox. (25L-S180, CL25S18) J 1.8k 1/16W M-Ox. (25L-S180, CL25S18) J 1.0k 1/16W M-Ox. (25L-S180, CL25S18) J 1.0k 1/16W M-Ox. (25L-S180, CL25S18) J 1.0k 1/16W M-Ox. (25L-S180, CL25S18) J 75 1/8W Carbon (25L-S100/180, CL25S18) J 100k 1/8W Carbon (25L-S100/180, CL25S18) J 100k 1/8W Carbon (25L-S100/180, CL25S18) J 100 1/8W Carbon (25L-S100/180, CL25S18) J 1.0k 1/8W Carbon (25L-S100/180, CL25S18) J 100 1/8W Carbon J 100 1/8W Carbon J 5.6k 1/8W Carbon J 10k 1/8W Carbon J 100 1/8W Carbon J 10k 1/16W M-Ox. J 22k 1/16W M-Ox. (25L-M100, CL25M10) J 220k 1/8W Carbon J 1.0k 1/8W Carbon J 1.0k 1/8W Carbon J Zener Diode, 5.1V (25L-M180, 25L-S100/180, CL25S18) J 560 1/8W Carbon (25L-M100, CL25M10) J 470 1/16W M-Ox. (25L-M180, 25L-S100/180, CL25S18) J 560 1/16W M-Ox. (25L-M100, CL25M10) J 22k 1/16W M-Ox. J 6.8k 1/8W Carbon J 6.8k 1/8W Carbon J 6.8k 1/8W Carbon J 6.8k 1/8W Carbon J 1.0k 1/8W Carbon J 10k 1/16W M-Ox. J 10k 1/16W M-Ox. J 10k 1/8W Carbon J 22k 1/8W Carbon J 1.0k 1/8W Carbon J 33k 1/8W Carbon J 100 1/8W Carbon J 33k 1/16W M-Ox. J 6.8k 1/8W Carbon J 100 1/8W Carbon J 100 1/8W Carbon J 220 1/16W M-Ox. J 5.6k 1/16W M-Ox. J 220 1/8W Carbon J 5.6k 1/8W Carbon J 18k 1/8W Carbon Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA 25L-M100/180/S100/180 CL25M10,CL25S18 Ref. No. ★ Part No. PWB-A: PWB-A: PWB-A: PWB-A: Code Ref. No. DUNTK9806WEK0 (25L-M100/CL25M10) DUNTK9806WEK1 (25L-M180) DUNTK9806WEK2 (25L-S100) DUNTK9806WEK3 (25L-S180/CL25S18) MAIN UNIT (Continued) R2063 VRD-MN2BE222J R2064 VRD-RA2BE332J R2066 VRS-CY1JF103J R2067 R2068 R2070 R2071 VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRD-RA2BE102J R2101 R2102 R2201 R2202 R2203 R2211 R2212 R2213 R2401 R2402 R2403 R2404 R2501 R2503 R2504 R2505 R2506 R2507 R2508 R2509 R2601 R3001 VRS-CY1JF101J VRS-CY1JF101J VRD-MN2BE222J VRS-CY1JF103J VRS-CY1JF184J VRD-MN2BE222J VRS-CY1JF682J VRS-CY1JF333J VRS-CY1JF101J VRS-CY1JF101J VRD-MN2BE101J VRD-MN2BE101J VRD-MN2BE103J VRD-MN2BE273J VRD-MN2BE123J VRD-MN2BE563J VRD-MN2BE563J VRD-MN2BE823J VRD-MN2BE153J VRD-MN2BE272J VRD-RA2BE331J VRD-RA2BE101J R3002 VRD-RA2BE101J R3003 VRS-CY1JF105J R3004 VRS-CY1JF104J R3005 VRS-CY1JF623J R3007 VRS-CY1JF332J R3008 VRS-CY1JF302J R3010 VRS-CY1JF392J R3011 VRD-MN2BE102J R3012 VRS-CY1JF102J R3013 VRD-MN2BE104J R3014 R3015 R3016 R3017 Description VRD-MN2BE104J VRD-RA2BE101J VRD-MN2BE750J VRD-RA2BE102J R3018 VRD-RA2BE102J J 2.2k 1/8W Carbon J 3.3k 1/8W Carbon J 10k 1/16W M-Ox. (25L-M100/180, CL25M10) J 10k 1/16W M-Ox. J 10k 1/16W M-Ox. J 10k 1/16W M-Ox. J 1.0k 1/8W Carbon (25L-S100/180, CL25S18) J 100 1/16W M-Ox. J 100 1/16W M-Ox. J 2.2k 1/8W Carbon J 10k 1/16W M-Ox. J 180k 1/16W M-Ox. J 2.2k 1/8W Carbon J 6.8k 1/16W M-Ox. J 33k 1/16W M-Ox. J 100 1/16W M-Ox. J 100 1/16W M-Ox. J 100 1/8W Carbon J 100 1/8W Carbon J 10k 1/8W Carbon J 27k 1/8W Carbon J 12k 1/8W Carbon J 56k 1/8W Carbon J 56k 1/8W Carbon J 82k 1/8W Carbon J 15k 1/8W Carbon J 2.7k 1/8W Carbon J 330 1/8W Carbon J 100 1/8W Carbon (25L-S100/180, CL25S18) J 100 1/8W Carbon (25L-S100/180, CL25S18) J 1.0M 1/16W M-Ox. (25L-S100/180, CL25S18) J 100k 1/16W M-Ox. (25L-S100/180, CL25S18) J 62k 1/16W M-Ox. (25L-S100/180, CL25S18) J 3.3k 1/16W M-Ox. (25L-S100/180, CL25S18) J 3.0k 1/16W M-Ox. (25L-S100/180, CL25S18) J 3.9k 1/16W M-Ox. (25L-S100/180, CL25S18) J 1.0k 1/8W Carbon (25L-S100/180, CL25S18) J 1.0k 1/16W M-Ox. J 100k 1/8W Carbon (25L-S100/180, CL25S18) J 100k 1/8W Carbon J 100 1/8W Carbon J 75 1/8W Carbon J 1.0k 1/8W Carbon (25L-S100/180, CL25S18) J 1.0k 1/8W Carbon (25L-S100/180, CL25S18) å AA AA AA AA AA AA AA QSW-K0079GEZZ QSW-K0079GEZZ QSW-K0079GEZZ QSW-K0079GEZZ QSW-K0079GEZZ J J J J J Power VOL-Down VOL-Up CH-Down CH-Up AB AA AA AA AA AA AA AA AA AA AA AB AA AA RY701 RRLYJ0081CEZZ J Relay P351 QPLGN0461CEZZ J LX-BZ3049GEFD LX-HZ3007MEFD AA AB AB AB AB AB MISCELLANEOUS PARTS å FB601 FB702 FB704 FB706 FH701 FH702 P351 QPLGN0160FJZZ QPLGN0461CEZZ QPLGN0361CEZZ QPLGN0207CEZZ QPLGN0269GEZZ QPLGN0561CEZZ QPLGN0561CEZZ QPLGN0561CEZZ RMC2601 RRMCU0235CEZZ HM501 LX-GZ3001PEZZ HM601 LX-GZ3001PEZZ HM602 LX-GZ3001PEZZ HM603 LX-GZ3001PEZZ HM604 LX-GZ3001PEZZ HM605 LX-GZ3001PEZZ HM606 LX-GZ3002PEZZ HM607 LX-GZ3002PEZZ HM608 LX-GZ3001PEZZ HM609 LX-GZ3001PEZZ HM610 LX-GZ3002PEZZ HM611 LX-GZ3002PEZZ HM612 LX-GZ3001PEZZ HM613 LX-GZ3002PEZZ HM614 LX-GZ3002PEZZ HM615 LX-GZ3002PEZZ HM616 LX-GZ3002PEZZ HM617 LX-GZ3001PEZZ HM618 LX-GZ3001PEZZ HM701 LX-GZ3001PEZZ HM702 LX-GZ3001PEZZ HM703 LX-GZ3001PEZZ HM704 LX-GZ3001PEZZ HM705 LX-GZ3001PEZZ HM706 LX-GZ3001PEZZ HM707 LX-GZ3001PEZZ HM708 LX-GZ3001PEZZ HM709 LX-GZ3001PEZZ HM710 LX-GZ3001PEZZ HM711 LX-GZ3001PEZZ HM712 LX-GZ3001PEZZ HM713 LX-GZ3001PEZZ RDA501 PRDAR0234PEFW RDA604 PRDAR0233PEFW RDA701 PRDAR1008MEFW RDA751 PRDAR5072CEFW TAN921 QTANJ0323CEZZ TAN921 QTANJ0523CEZZ AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AL 46 ★ QFS-B4023CEZZ or QFS-B4021GEZZ RBLN-0047CEZZ RBLN-0036CEZZ RBLN-0037CEZZ RBLN-0037CEZZ QFSHD1013CEZZ QFSHD1014CEZZ QPLGN0361CEZZ P601 P621 P651 P701 P703 P901 P903 P2401 SWITCHES S2501 S2502 S2503 S2504 S2505 F701 Part No. Description Code J Fuse 4A 125V AC J J J J J J J AB AB AB AB AC AC AB J J J J J J J J J R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R M J J M J M Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Fuse Holder Fuse Holder Plug 3-pin (S) (25L-M100/180, CL25M10) Plug 4-pin (K) (25L-S100/180, CL25S18) Plug 5-pin (K) Plug 4-pin (YBN) Plug 3-pin Plug 2-pin (M) Plug 2-pin (P) Plug 5-pin (HA) Plug 5-pin (GBN) Plug 5-pin R/C Receiver Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Heat Sink IC501 Heat Sink Q602 Heat Sink IC701 Heat Sink IC751 AV Terminal (25L-S100) AV Terminal (25L-S180, CL25S18) Screw Screw AB AD AB AB AA AB AB AB AB AK AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AH AK AH AC AL AG AA AA 25L-M100/180/S100/180 CL25M10,CL25S18 Ref. No. ★ Part No. Description Code Ref. No. CRT UNIT TRANSISTORS VS2SC3198-Y-1 VS2SC3789//2E VS2SC3198-Y-1 VS2SC3789//2E VS2SC3198-Y-1 VS2SC3789//2E VS2SA1266-Y-1 J M J M J M J VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 L851 VP-MK820K0000 AA AA AA AA AA AA AA J Diode J Diode J Diode J1001 QJAKE0053GEZZ J1002 QJAKE0055GEZZ J Jack, Video in J Jack, Audio in (L) (25L-S100/180, CL25S18) J1003 QJAKE0055GEZZ J Jack, Audio in (25L-M100/180, CL25M10) J1003 QJAKE0059GEZZ J Jack, Audin in (R) (25L-M100/180, CL25M10) P1001 QPLGN0541CEZZ J Plug, 5-pin (HA) AB AB AB COIL J Peaking 82µH AB CAPACITORS C851 C852 C853 C854 C883 [EL.··· Electrolytic] VCCSPA1HL391J J 390p 50V VCCSPA1HL331J J 330p 50V VCCSPA1HL391J J 390p 50V RC-KZ0024CEZZ J 0.001 2kV VCEA0A1HW106M J 10 50V R851 R852 R853 R855 R856 å R857 R858 R859 R860 R861 R863 R864 å R865 R866 R867 R868 R869 R871 R872 å R873 R874 R881 R882 R883 R884 R895 [M-Ox.··· Metal Oxide.] VRD-RA2BE470J J 47 1/8W VRD-RA2BE181J J 180 1/8W VRD-RA2BE121J J 120 1/8W VRD-RA2BE471J J 470 1/8W VRD-RA2BE221J J 220 1/8W VRS-VV3LB123J J 12k 3.0W VRD-RM2HD222J J 2.2k 1/2W VRD-RA2BE470J J 47 1/8W VRD-RA2BE181J J 180 1/8W VRD-RA2BE121J J 120 1/8W VRD-RA2BE471J J 470 1/8W VRD-RA2BE221J J 220 1/8W VRS-VV3LB123J J 12k 3.0W VRD-RM2HD222J J 2.2k 1/2W VRD-RA2BE470J J 47 1/8W VRD-RA2BE181J J 180 1/8W VRD-RA2BE121J J 120 1/8W VRD-RA2BE471J J 470 1/8W VRD-RA2BE221J J 220 1/8W VRS-VV3LB123J J 12k 3.0W VRD-RM2HD222J J 2.2k 1/2W VRD-RA2BE102J J 1.0k 1/8W VRD-RA2BE331J J 330 1/8W VRD-RA2BE561J J 560 1/8W VRD-RA2BE152J J 1.5k 1/8W VRD-RA2BE470J J 47 1/8W Description Code MISCELLANEOUS PARTS 2SC3198 2SC3789 2SC3198 2SC3789 2SC3198 2SC3789 2SA1266 DIODES D881 D882 D884 ★ PWB-H: DUNTK9310WEK0 (25L-M100/180, CL25M10) PWB-H: DUNTK9310WEK1 (25L-S100/180, CL25S18) FRONT AV UNIT PWB: DUNTK9510WEK1 Q851 Q852 Q853 Q854 Q855 Q856 Q881 Part No. Ceramic Ceramic Ceramic Ceramic EL. AA AA AA AC AB Carbon Carbon Carbon Carbon Carbon M-Ox. Carbon Carbon Carbon Carbon Carbon Carbon M-Ox. Carbon Carbon Carbon Carbon Carbon Carbon M-Ox. Carbon Carbon Carbon Carbon Carbon Carbon AA AA AA AA AA AB AA AA AA AA AA AA AB AA AA AA AA AA AA AB AA AA AA AA AA AA RESISTORS MISCELLANEOUS PARTS P851 QPLGN0541CEZZ J Plug, 5-pin(GBN) P852 QPLGN0441CEZZ J Plug, 4-pin(YBN) SC851 QSOCV0937CEZZ M CRT Socket AB AB AF 47 AD AD AD AC AB 25L-M100/180/S100/180 CL25M10,CL25S18 Ref. No. Part No. ★ Description Code Ref. No. MISCELLANEOUS PARTS å ACC701 å ACC701 SP1 SP2 QACCD3070CESA M AC Cord (25L-M100/180, CL25M10) QACCD3065CESA M AC Cord (25L-S100/180, CL25S18) QCNW-0133MEZZ M Connecting Cord (25L-M100/180, CL25M10) QCNW-0135MEZZ M Connecting Cord (25L-M100/180, CL25M10) QCNW-0130MEZZ M Connecting Cord (25L-S100/180, CL25S18) QCNW-0134MEZ M Connecting Cord (25L-S100/180, CL25S18) QCNW-0166MEZZ M Connecting Cord QCNW-0167MEZZ M Connecting Cord VSP0080PBL4YS M Speaker, 32 ohm VSP0080PBL4YS M Speaker, 32 ohm (25L-S100/180, CL25S18) M Registration Card (U.S.A. only) TiNS-6548MEZZ M Operation Manual (25L-M100, CL25M10) TiNS-6549MEZZ M Operation Manual (25L-M180) TiNS-6550MEZZ M Operation Manual (25L-S100) TiNS-6551MEZZ M Operation Manual (25L-S180, CL25S18) RRMCG1324CESA M Infrared R/C Unit (25L-M100, CL25M10, 25L-S100) RRMCG1395CESA M Infrared R/C Unit (25L-M180, 25L-S180, CL25S18) AH SPAKC0635MEZZ SPAKX0162MEZZ SPAKX0170MEZZ SSAKA0004MEZZ – Packing Case (25L-M100/180, CL25M10) – Packing Case (25L-S100/180, CL25S18) – Buffer Material (25L-M100/180, CL25M10) – Buffer Material (25L-S100/180, CL25S18) – Polyethylene Foam Sheet Code 25L-M100/180, CL25M10 1 AG 1 AC 1-1 1-2 1-3 1-4 1-5 2 AF AF AE AD AC AG AG CCABA1277MES1 M Front Cabinet Ass'y (25L-M100, CL25M10) CCABA1297MES1 M Front Cabinet Ass'y (25L-M180) Not Available – Front Cabinet HBDGB1008MESA M Badge, "SHARP" JBTN-1086MEKA M Button, Power, Vol-up/down JBTN-1087MEKA M Button, CH-up/down GCOVA1028MEKA M Cover for R/C GCABB1145MEKA M Rear Cabinet BE BE — AA AD AD AD AZ 25L-S100/180, CL25S18 1 1 1-1 1-2 1-3 1-4 1-5 2 2 CCABA1298MES1 M Front Cabinet Ass'y (25L-S100) CCABA1299MES1 M Front Cabinet Ass'y (25L-S180, CL25S18) Not Available – Front Cabinet HBDGB3009MESA M Badge, "SHARP" JBTN-1103MEKA M Button, Power, Vol-up/down JBTN-1104MEKA M Button, CH-up/down GCOVA1038MEKA M Cover for R/C GCABB1146MEKA M Rear Cabinet (25L-S100) GCABB1147MEKA M Rear Cabinet (25L-S180, CL25S18) BE BE — AC AE AE AC AZ AA AP CABINET PARTS LOCATION AD AD 1 1-1 AD 2 AT AW PACKING PARTS (NOT REPLACEMENT ITEM) SPAKC0634MEZZ Description CABINET PARTS SUPPLIED ACCESORRIES TGAN-1006MEZZ ★ Part No. 25L-M100/180 CL25M10 1-3 1-2 1-5 1-4 1 1-1 — 2 — — — 25L-S100/180 CL25S18 48 1-3 1-2 1-5 1-4 25L-M100/180/S100/180 CL25M10,CL25S18 Ref. No. Part No. ★ Description Code No. Part No. PACKING OFRef. THE SET ★ Description Code ★ Polyethylene Bag Operation Manual Registration Card (U.S.A.) Infrared R/C Unit ★ Batteries ★ Polyethylene Foam Sheet ★ Buffer Material FRONT ★ Packing Case Use tapes to fix the packing case. ★ Bar Code Label REAR MARK ★ : Not replacement items. 49 25L-M100/180/S100/180 CL25M10,CL25S18 Ref. No. Part No. ★ Description Code Ref. No. ★ Part No. Description Code COPYRIGHT © 1999 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. SHARP CORPORATION AV Systems Group Quality & Reliability Control Center Yaita, Tochigi 329-2193, Japan TQ0633-S Apr. 1999 Printed in Japan SY. KG 50 ">
Публичная ссылка обновлена
Публичная ссылка на ваш чат обновлена.