13K-M100/150 CK13M10/15 SERVICE MANUAL S28L513K-M100 COLOR TELEVISION Chassis No. SN-80 13K-M100/150 CK13M10/15 MODELS In the interests of user-safety (Required by safety regulations in some countries ) the set should be restored to its original condition and only parts identical to those specified should be used. ELECTRICAL SPECIFICATIONS POWER INPUT ........................... 120 V AC 60 Hz POWER RATING .......................................... 69 W PICTURE SIZE ..................... 580cm2(89.9sq inch) CONVERGENCE .................................... Magnetic SWEEP DEFLECTION ........................... Magnetic FOCUS ....................... Hi-Bi-Potential Electrostatic INTERMEDIATE FREQUENCIES Picture IF Carrier Frequency ............. 45.75 MHz Sound IF Carrier Frequency ............. 41.25 MHz Color Sub-Carrier Frequency ............ 42.17 MHz (Nominal) AUDIO POWER OUTPUT RATING ........ 0.9W (at 10% distortion) SPEAKER SIZE ................................................ 8cm(Round) VOICE COIL IMPEDANCE ....... 8ohm at 400 Hz ANTENNA INPUT IMPEDANCE VHF/UHF ............................ 75 ohm Unbalanced TUNING RANGES VHF-Channels ....................................... 2thru 13 UHF-Channels ..................................... 14thru 69 CATV Channels .................................... 1thru 125 USA: (EIA, Channel Plan) Specifications are subject to change without prior notice. CONTENTS æ æ æ æ æ æ æ æ æ æ æ Page ELECTRICAL SPECIFICATIONS ........................................................................................... 1 IMPORTANT SERVICE SAFETY PRECAUTION ................................................................... 2 LOCATION OF USER'S CONTROL ....................................................................................... 6 INSTALLATION AND SERVICE INSTRUCTIONS .................................................................. 7 CHASSIS LAYOUT ............................................................................................................... 13 BLOCK DIAGRAM ................................................................................................................ 14 DESCRIPTION OF SCHEMATIC DIAGRAMS ..................................................................... 15 SCHEMATIC DIAGRAMS ..................................................................................................... 16 PRINTED WIRING BOARD ASSEMBLIES .......................................................................... 19 REPLACEMENT PARTS LIST .............................................................................................. 23 PACKING OF THE SET ........................................................................................................ 30 SHARP CORPORATION This document has been published to be used for after sales service only. The contents are subject to change without notice. 1 13K-M100/150 CK13M10/15 IMPORTANT SERVICE SAFETY PRECAUTION Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and servicing guidelines which follow: WARNING X-RADIATION AND HIGH VOLTAGE 1. For continued safety, no modification of any circuit should be attempted. 2. Disconnect AC power before servicing. 3. Semiconductor heat sinks are potential shock hazards when the chassis is operating. 4. The chassis in this receiver has two ground systems which are separated by insulation material. The nonisolated (hot) ground system is for the B+ voltage regulator circuit and the horizontal output circuit.The isolated ground system is for the low B+ DC voltages and the secondary circuit of the high voltage transformer. To prevent electrical shock use an isolation transformer between the line cord and power receptacle, when servicing this chassis. LIMITS 4A 125V CAUTION: FOR CONTINUED PROTECTION AGAINST A RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 4A125V FUSE. SERVICING OF HIGH VOLTAGE SYSTEM AND PICTURE TUBE When servicing the high voltage system, remove the static charge by connecting a 10k ohm resistor in series with an insulated wire (such as a test probe) between the picture tube ground and the anode lead. (AC line cord should be disconnected from AC outlet.) 1. Picture tube in this receiver employs integral implosion protection. 2. Replace with tube of the same type number for continued safety. 3. Do not lift picture tube by the neck. 4. Handle the picture tube only when wearing shatterproof goggles and after discharging the high voltage anode completely. 1. Be sure all service personnel are aware of the procedures and instructions covering X-radiation. The only potential source of X-ray in current solid state TV receivers is the picture tube. However, the picture tube does not emit measurable X-Ray radiation if the high voltage is as specified in the "High Voltage Check" instructions. It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the picture tube including the lead in glass material. The important precaution is to keep the high voltage below the maximum level specified. 2. It is essential that service personal have available at all times an accurate high voltage meter. The calibration of this meter should be checked periodically. 3. High voltage should always be kept at the rated value −no higher. Operation at higher voltages may cause a failure of the picture tube or high voltage circuitry and; also under certain conditions, may produce radiation that exceeds specifications. 4. When the high voltage regulator is operating properly there is no possibility of an X-radiation problem. Every time a color chassis is serviced, the brightness should be tested while monitoring the high voltage with a meter to be certain that the high voltage does not exceed the specified value and that it is regulating correctly. 5. Do not use a picture tube other than that specified or make unrecommended circuit modifications to the high voltage circuitry. 6. When trouble shooting and taking test measurements on a receiver with excessive high voltage, avoid being unnecessarily close to the receiver. Do not operate the receiver longer than is necessary to locate the cause of excessive voltage. 2 13K-M100/150 CK13M10/15 IMPORTANT SERVICE SAFETY PRECAUTION (Continued) RETBEFOREURNING THE RECEIVER æ (Fire & Shock Hazard) Before returning the receiver to the user, perform the following safety checks. 1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the receiver. 2. Inspect all protective devices such as non-metallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacity networks, mechanical insulators, etc. 3. To be sure that no shock hazard exists, check for leakage current in the following manner. æ Plug the AC cord directly into a 120 volt AC outlet, (Do not use an isolation transformer for this test). æ Using to clip leads, connect a 1.5k ohm, Iê watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal cabinet parts and a known earth ground, such as electrical conduit or electrical ground connected to earth ground. æ Use an AC voltmeter having with 5000 ohm per volt, or higher, sensitivity to measure the AC voltage drop across the resistor. Connect the resistor connection to all exposed metal parts having a return to the chassis (antenna, metal cabinet, screw heads, knobs and control shafts, escutcheon, etc.) and measure the AC voltage drop across the resistor. AII check must be repeated with the AC line cord plug connection reversed. (IF necessary, a nonpolarized adapter plug must be used only for the purpose of completing these check.) Any current measured must not exceed 0.5 milliamp. Any measurements not within the limits outlined above are indicative of a potential shock hazard and corrective action must be taken before returning the instrument to the customer. AC VOLTMETER 1.5k ohm 10w 0.15µF TEST PROBE TO EXPOSED METAL PARTS CONNECT TO KNOWN EARTH GROUND 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 SAFETY NOTICE For continued protection, replacement parts must be Many electrical and mechanical parts in television identical to those used in the original circuit. receivers have special safety-related characteristics. These characteristics are often not evident from visual The use of substitute replacement parts which do not inspection, nor can protection afforded by them be have the same safety characteristics as the factory necessarily increased by using replacement components recommended replacement parts shown in this service rated for higher voltage, wattage, etc. manual, may create shock, fire, X-radiation or other Replacement parts which have special safety hazards. characteristics are identified in this manual; electrical components having such features are identified by "å" and shaded areas in the Replacement Parts Lists and Schematic Diagrams. 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 3 13K-M100/150 CK13M10/15 PRECAUTIONS A PRENDRE LORS DE LA REPARATION Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux conseils suivants. AVERTISSEMENT 1. N'entreprendre aucune modification de tout circuit. C'est dangereux. 2. Débrancher le récepteur avant toute réparation. 3. Les déversoirs thermiques à semi-conducteurs peuvent présenter un danger de choc électrique lorsque le réceqteur est en marche. 4. Le châssis de ce récepteur possède deux systèmes de masse qui sont séparées par du matériel d'isolation. Le système de masse non-isolée (sous tension) est pour le circuit du régulateur de tension + B et le circuit de sortie horizontale. Le système de masse isolée est pour les tensions DC + B basses et le circuit secondaire du transformateur haute tension. Pour éviter tout risque d'électrocution lors de l'entretien de ce châssis, utiliser un transformateur d'isolation entre le cordon de ligne et la prise de courant. 4A 125V PRECAUTION:POUR LA PROTECTION CONTINUE CONTRE LES RISQUES D'INCENDIE, REMPLACER LE FUSIBLE PAR UN FUSIBLE DE MEME TYPE 4A-125V. REPARATION DU SYSTEME A HAUTE TENSION ET DU TUBE-IMAGE Lors de la réparation de ce systéme, supprimer la charge statique en branchant une résistance de 10 kΩ en série avec un fil isolé (comme une sonde d'essai) entre la mise à la terre du tube-image et le fil d'anodel. (Le corden d'alimentation doit être retiré de la prise murale.) 1. Le tube image dans ce récepteur emploie une protection intégrée contre l'implosion. 2. Par mesure de sécurité, changer le tube-image pour un tube du même numéro de type. 3. Ne pas lever le tube-image par son col. 4. Ne manipuler le tube-image qu'en porant des lunettes incassables et qu'après avoir déchargé totalement la haute tension. LIMITES DES RADIATIONS X ET DE LA HAUTE TENSION 1. Tout le personnel réparateur doit être instruit des instructions et procédés relatifs aux radiations X. Le tube-image, seule source de rayons X dons les téleviseurs transistorisés, n'émet pourtant pas de rayons mesurables si la haute tension est maintenue à un niveau préconisé dans la section "Vérification de la haute tension". C'est seulement quand la haute tension est excessive que les rayons X peuvent entrer dans l'enveloppe du tube-image y compris le conducteur de verre. Il est important de maintenir la haute tension endessous du niveau spécifié. 2. Il est essentiel que le réparateur ait sous la main un voltmètre à haute tension qui doit être périodiquement étalonné. 3. La haute tension doit toujours être maintenue à la valeur de régime -et pas plus haute. L'opération à des tensions plus élevées peut entraîner une panne du tube-image ou du circuit à haute tension et, dans certaines conditions, peut entraîner une radiation dépassant les niveaux préscrits. 4. Quand le régulateur à haute tension fonctionne correctement, il n'y a aucun problème de radiation X. Chaque fois qu'un châssis couleurs est réparé, la luminosité doit être examinée bout en contrôlant la haute tension à l'aide d'un voltmètre pour s'assurer que la haute tension ne dépasse pas la valeur spécifiée et qu'elle soit correctement réglée. 5. Ne pas utiliser un tube-image autre que celui spécifié et ne pas effectuer de modifications déconseillées du circuit à haute tension. 6. Lors de la recherche des pannes et des mesures d'essai sur un récepteur qui présente une haute tension excessive, éviter de s'approcher inutilement du récepteur. Ne pas faire fonctionner le récepteur plus longtemps que nécessaire pour localiser la cause de la tension excessive. 4 13K-M100/150 CK13M10/15 PRECAUTIONS A PRENDRE LORS DE LA REPARATION (Suite) VERIFICATIONS CONTRE L'INCEN-DIE ET LE CHOC ELECTRIQUE æ Avant de rendre le récepteur à l'utilisateur, effectuer les vérifications suivantes. 1. Inspecter tous les faisceaux de câbles pour s'assurer que les fils ne soient pas pincés ou qu'un outil ne soit pas placé entre le châssis et les autres pièces métalliques du récepteur. 2. Inspecter tous les dispositifs de protection comme les boutons de commande non-métalliques, les isolants, le dos du coffret, les couvercles ou blindages de réglage et de compartiment, les réseaux de résistance-capacité, les isolateurs mécaniques, etc. 3. S'assurer qu'il n'y ait pas de danger d'électrocution en vérifiant la fuite de courant, de la facon suivante: æ Brancher le cordon d'alimentation directem-ent à une prise de courant de 120V. (Ne pas utiliser de transformateur d'isolation pour cet essai). æ A l'aide de deux fils à pinces, brancher une résistance de 1,5 kΩ 10 watts en parallèle avec un condensateur de 0,15µF en série avec toutes les pièces métalliques exposées du coffret et une terre connue comme une conduite électrique ou une prise de terre branchée à la terre. æ Utiliser un voltmètre CA d'une sensibilité d'au moins 5000Ω/V pour mesurer la chute de tension en travers de la résistance. Toucher avec la sonde d'essai les pièces métalliques exposées qui présentent une voie de retour au châssis (antenne, coffret métallique, tête des vis, arbres de commande et des boutons, écusson, etc.) et mesurer la chute de tension CA en-travers de la résistance. Toutes les vérifications doivent être refaites après avoir inversé la fiche du cordon d'alimentation. (Si nécessaire, une prise d'adpatation non polarisée peut être utilisée dans le but de terminer ces vérifications.) Tous les courants mesurés ne doivent pas dépasser 0,5 mA. Dans le cas contraire, il y a une possibilité de choc électrique qui doit être supprimée avant de rendre le récepteur au client. AC CA Voltmètre VOLTMETER 1.5k ohm 10w 0.15µF SONDE D'ESSAI TEST PROBE AUX PIECES TO EXPOSED METALLIQUES METAL PARTS EXPOSEES BRANCHER A TO UNE CONNECT TERRE CONNUE KNOWN EARTH GROUND 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 AVIS POUR LA SECURITE De nombreuses pièces, électriques et mécaniques, dans les téléviseurs présentent des caractéristiques spéciales relatives à la sécurité, qui ne sont souvent pas évidentes à vue. Le degré de protection ne peut pas être nécessairement augmentée en utilisant des pièces de remplacement étalonnées pour haute tension, puissance, etc. Les pièces de remplacement qui présentent ces caractéristiques sont identifiées dans ce manuel; les pièces électriques qui présentent ces particularités sont identifiées par la marque " å " et hachurées dans la liste des pièces de remplacement et les diagrammes schématiques. Pour assurer la protection, ces pièces doivent être identiques à celles utilisées dans le circuit d'origine. L'utilisation de pièces qui n'ont pas les mêmes caractéristiques que les pièces recommandées par l'usine, indiquées dans ce manuel, peut provoquer des électrocutions, incendies, radiations X ou autres accidents. 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 5 13K-M100/150 CK13M10/15 LOCATION OF USER'S CONTROL 6 13K-M100/150 CK13M10/15 INSTALLATION AND SERVICE INSTRUCTIONS Note: (1) (2) When performing any adjustments to resistor controls and transformers use non-metallic screwdriver or TV alignment tools. Before performing adjustment, TV set must be on at least 15 minutes. CIRCUIT PROTECTION The receiver is protected by a 4.0A fuse (F701), mounted on PWB-A, wired into one side of the AC line input. X-RADIATION PROTECTOR CIRCUIT TEST 1. After service has been performed on the horizontal deflection system, high voltage system, B + system, test the X-Radiation protection circuit to ascertain proper operation as follows: 1) Apply 120V AC using a variac transformer for accurate input voltage. 2) Allow for warm up and adjust all customer controls for normal picture and sound. 3) Select a local channel. 4) Connect a digital voltmeter to TP653 and make sure that the voltmeter reads 21.3V ±1.5V. 5) Apply external 28.9V DC at TP653 by using an external DC supply, TV must be shut off. 6) To reset the protector, unplug the AC cord and make a short circuit between TP651 and TP652.Now make sure that normal picture appears on the screen. 7) If the operation of the horizontal oscillator does not stop in step 5, the circuit must be repaired before the set is returned to the customer. 7 HIGH VOLTAGE CHECK High voltage is not adjustable but must be checke to verify that the receiver is operating within safe and efficient design limitations as specified checks should be as follows: 1. Connect an accurate high voltage meter between ground and anode of picture tube. 2. Operate receiver for at least 15 minutes at 120V AC line voltage, with strong air signal or properly tuned in test signal. 3. Set service mode on (See next page.),Service No.S19 and Bus data "01" (Y-mute on). 4. The voltage should be approximately 24.0kV (at zero beam)." If a correct reading cannot be obtained, check circuitry for malfunctioning components. After the voltage test,make Y-mute off (normal mode). 13K-M100/150 CK13M10/15 For adjustments of this model, the bus data is convered to various analog signals by the D-A converter circuit. Note: There are still a few analog adjustments in this series such as focus and master screen voltage. Follow the steps below whenever service adjustment is required. See Figure "B" to determine if service adjustments are required. 1.Service mode Before putting unit into the service mode, check, that customer adjustments are in the normal mode. use the reset function in the video adjust menu to ensure customer controls are in their To enter the service mode . While Pressing the Vol-up and Ch-up buttons at once,plug the AC cord into a wall socket.Now the TV set is switched on and enters the service mode. To exit the service mode, shut the television off by pressing the power button. 2.Service number selection Once in the service mode, press the channel up or channel down button on the remote transmitter or at the set. the service adjustment number will vary in increments of one, from "S01" to "S19". Select the item you wish to adjust. 3.Data number selection Press the volume up or down button to adjust the data number. DATA NUMBER (HEX ) (HEXADEC:MAL) DA1A NUMBER (DEC) (DECIMAL) SERVICE ADJUSTMENT NUMBER S01 55 02 S01 D:00 Figure B. 8 13K-M100/150 CK13M10/15 SERVICE NUMBER S01 S02 S03 S04 S05 S06 S07 S08 S09 S10 S11 S12 S13 S14 S15 S16 S17 S18 S19 DATA ADJUSTMENT ITEM INITIAL VALUE RANGE PICTURE TINT COLOR BRIGHTNESS SHARPNESS VERTICAL PHASE HORIZONTAL PHASE RF-AGC VERTICAL AMP VCO R CUT-OFF G CUT -OFF B CUT-OFF G GAIN B GAIN TRAP(3.58MHz) BALANCE C.C.POSITION Y-MUTE 55 46 32 40 28 00 12 2A 20 2C 00 00 00 7F 7F 00 20 18 00 00-7F 00-7F 00-7F 00-7F 00-3F 00-07 00-1F 00-3F 00-3F 00-7F 00-FF 00-FF 00-FF 00-FF 00-FF 00 or 01 00-3F 00-7F 00,01,03 ADJUSTMENT CONTENTS Must be set to “24” Must be set between "0" to "03" Must be set to “00” Must be set to “20” 00=NORMAL, 01=no”Y, 03=NO VERTICAL” Table - A Holding down both the CH UP/DOWN keys on the TV set at service mode for more then 2 seconds will automatically write the above initial values into IC2101. ADJUSTMENT PART REPLACED NECESSARY UNNECESSARY X IC2001 NOTES Data is stored in IC2101. X The adjustment is needed to compensate for characteristics of parts including IC201. IC2101 X Holding down both the CH UP/DOWN keys on the TV set at service mode for more than 2 seconds will automatically write the above initial values into IC2101. CRT X IC201 Adjust items related to picture tube only. Table - B 9 13K-M100/150 CK13M10/15 Ë adjustment VCO Adjustment 1. Connect a digital voltmeter between pin (44) of IC201 and ground. 2. Select a good local channel. 3. Enter the service mode. select adjustment "S10". 4. Adjust the data so that digital voltmeter should read 2.2V 5. Adjustment is complete, remove the volt-meter, return to "normal" mode. RF AGC Adjustment 1. Have unit receive a good local channel. 2. Enter the service mode and select service adjustment "S08". 3. Set the data value to point where no noise or beat appears. 4. Select another channel to confirm that no noise or beat appears. NOTE 1 :You will have to come out of the service mode to select another channel. NOTE 2 :Setting the data to "00" will pro-duce a black raster. White balance adjustment 1. Have unit receive a good local channel. 2. Enter the service mode. select service adjustment "S03" and set to "00" ( minimum color) . "S03" does not have to be adjusted if you selected a B/W picture or monoscope pattern. 3. Alternately adjust service adjustment data of "S14" and "S15" untill a good grey scale with normal whites is obtained. 4. Select service adjustment "S03" and adjust data to obtain normal color level. Sub-picture adjustment 1. Have unit receive a good local channel. 2. Make sure the customer picture control is set to maximum. 3. Enter the service mode and select service adjustment "S01". 4. Adjust the data value to achieve normal contrast range. Sub-Tint Adjustment Screen adjustment 1. Connect a digital voltmeter between TP852 and TP853 on the CRT socket PWB. Note:These test points may not be provided. Then connect the voltmeter to both ends of R852 located near Q852 on the foil side. 2. Select a good local channel. 3. Enter the service mode and select service adjustment “S03” and set the data value to “00” to set the color level to minimum.(Record original data code under adjustment “S03” before changing) You may skip this step if you selected a B/W picture or monoscope pattern. 4. Select service adjustment “S19” and adjust the data value to “01” this turn off the luminance signal (Ymute). 5. Select service adjustment "S04" and adjust data value to obtain 0.17 volts on the digital voltmeter. 6. Adjust the master screen cotrol untill raster darkens to the point where raster is barely seen. 7. Adjust service adjustments "S11" red, "S12" green and "S13" blue to obtain a good grey scale with normal whites at low brightness level. 8. Select service adjustment “S19” and reset data to “00”. Select service adjustment “S03” and reset data to obtain normal color level. 9. Remove digital voltmeter. Reset master screen cotrol to obtain normal brightness range. 1. Have unit receive a good local channel. 2. Set customer tint control to center of it's range. 3. Enter the service mode and select service adjustment "S02". 4. Adjust "S 02" data value to obtain normal flesh tones. 10 13K-M100/150 CK13M10/15 Sub-color adjustment Horizontal position adjustment 1. Have unit receive a good local channel. 2. Make sure the customer color control is set to center position . 3. Enter the service mode and select service adjustment "S03". 4. Adjust "S03"data value to obtain normal color level. 1. Have unit receive a good local channel. 2. Enter the service mode and select service adjustment "S07". 3. Adjust "S07" data value so that picture is centered. Sub-brightness adjustment 1. Have unit receive a good local channel. 2. Enter the service mode and select service adjustment "S18". 3. A black text box appears on the screen (see Figure C). 4. Adjust "S18" data value so that text box is positioned in the center of the screen. 1. Have unit receive a good local channel. 2. Make sure the customer brightness control is set to center position. 3. Enter the service mode and select service adjustment "S04". 4. Adjust "S04"data value to obtain normal brightness level. Vertical-size adjustment 1. Have unit receive a good local channel. 2. Enter the service mode and select service adjustment "S09". 3. While observing the top and bottom of the screen, adjust "S09" data value to proper vertical size . Vertical phase adjustment 1. Enter the service mode and select service adjustment "S06". 2. Adjust data value to "00"~"03" so that picture is approximate center. Note: This must be set "00"~"03" when adjust another data retrace line will be appear. Caption position adjustment (horizontal) 3.58MHz trap adjustment 1. Have unit receive a good local channel. 2. Enter the service mode and select service adjustment "S16" . 3. This is a two position adjustment, "00" is ON , "01" is OFF. 4. Adjust data value to "00" for normal viewing. Sharpness and Audio balance adjustments 1. Have unit receive a good local channel. 2. Enter the service mode and select "S05" for sharpness and "S17" for balance. • Sharpness adjustments 3. Adjust data value to "24" (center of data range) for sharpness adjustment. • Audio balance adjustments 4. Adjust data value to "20" (center of data range) for Audio balance adjustment. Figure C. 11 13K-M100/150 CK13M10/15 Memo 12 13K-M100/150 CK13M10/15 13K-M100/150 CK13M10/15 CHASSIS LAYOUT BLOCK DIAGRAM H H G G F F E E D D C C B B A A 1 2 3 4 13 5 6 1 2 3 4 14 5 6 13K-M100/150 CK13M10/15 13K-M100/150 CK13M10/15 DESCRIPTION OF SCHEMATIC DIAGRAM NOTE: H 1. The unit of resistance "ohm" is omitted (K:1000 ohms, M:1 Meg ohm). 2. All resistors are 1/8 watt, unless otherwise noted. 3. All capacitors are µ F, unless otherwise noted P: µµ F. 4. (G) indicates ±2% tolerance may be used. 5. indecates line isolated ground. G 6. indecates hot ground. VOLTAGE MEASUREMENT CONDITIONS: 1. All DC voltages are measured with DVM connected between points indicated and chassis ground, line voltage set at 120V AC and all controls set for F normal picture unless otherwise indicated. 2. All voltages measured with 1000µ V B & W or Color signal. SCHEMATIC DIAGRAM :CRT Unit WAVEFORM MEASUREMENT CONDITIONS: 1. Photographs taken on a standard gated color bar signal, the tint setting adjusted for proper color. The wave shapes at the red, green and blue cathodes of the picture tube depend on the tint, color level and picture control. 2. indicates waveform check points (See chart, waveforms are measured from point indicated to chassis ground.) H G å AND SHADED ( ) COMPONENTS = SAFETY RELATED PARTS. ▲ MARK= X-RAY RELATED PARTS. DRGANNES MARQUES å ET HACHRES ( ): PIECES RELATIVES A LA SECURITE. MARQUE ▲ : PIECS RELATIVE AUX RAYONS X. F This circuit diagram is a standard one, printed circuits may be subject to change for product improvement without prior notice. E E D D C C B B A A 1 2 3 4 15 5 6 1 2 3 4 16 5 6 13K-M100/150 CK13M10/15 13K-M100/150 CK13M10/15 SCHEMATIC DIAGRAM:MAIN Unit H G F E D C B A 1 2 3 4 17 5 6 7 8 9 10 18 11 12 13K-M100/150 CK13M10/15 13K-M100/150 CK13M10/15 PRINTED WIRING BOARD ASSEMBLIES H G F PWB-B:CRT Unit (Wiring Side) E D C B A PWB-A:MAIN Unit (Wiring Side) 1 2 3 19 4 5 6 7 8 9 10 20 11 12 13K-M100/150 CK13M10/15 13K-M100/150 CK13M10/15 H G F E D C B A PWB-A:MAIN Unit (Chip Parts Side) 1 2 3 4 21 5 6 7 8 9 10 22 11 12 13K-M100/150 CK13M10/15 13K-M100/150 CK13M10/15 PARTS LIST LISTE DES PIECES PARTS REPLACEMENT CHANGE DES PIECES Replacement parts which have these special safety characteristics identified in this manual ; electrical components having such features are identified by å and shaded areas in the Replacement Parts Lists and Schematic Diagrams. The use of a substitute replacement part which dose no have the same safety characteristic as the factory recommended replacement parts shown in this service manual may create shock, fire or other hazards. Les pi`eces de rechange qui pr élelesentent ces caract éleristiques sp éleciales de s élecurit éle, sont identifi élees dans ce manuel : les pi`eces élelectriques qui pr élesentent ces particularit éles, sont rep éler élee par la marque å et sont hachur élees dans les listes de pi`eces et dans les diagrammes sch élematiques. La substitution d'une pi`ece de rechange par une autre qui ne pr éLesente pas les m éoemes caract éLeristiques de s élecurit éle que la pi`ece recommand élee parl'usine et dans ce manuel de service, peut provoquer une éLelectrocution, un incendie ou toutautre sinistre. "HOW TO ORDER REPLACEMENT PARTS" To have your order filled promptly and correctly, please furnish the following informations. 1. MODEL NUMBER 2. REF. NO. 3. PART NO. 4. DESCRIPTION in USA: MARK★: SPARE PARTS-DELIVERY SECTION ★ Description or or or or or ç åDY601 or or åL702 VB370BVBK1U-S VB370BVBK1S-S VB34JFQ90X/*S VB34KPU02X/*S VB34JLL40X/*S VB37GDA86X/1E RCiLH0141PEZZ RCiLH0142PEZZ RCiLH0143PEZZ RCiLG0386PEZZ PMAGF3041CEZZ PSPAG0004PEZZ QEARC1404PEZZ MSPRT0001PEFJ R R R R R R R R R R J R R R 3. NO. DE PIECE 4. DESCRIPTION Code Ref. No. MARQUE : PIECES RELATIVE AUX RAYONS X ★ Part No. Description Code DUNTK9529WEV0/V4 MAIN Unit CRT ( DY601:H0143PE) BX CRT ( DY601:H0143PE) BZ CRT( DY601:H0143PE ) CB CR ( DY601:H0141PE ) BX CRT ( DY601:H0144PE ) BX CRT ( DY601:H0142PE ) BX DY ( CRT:A34KPU02XX) BA DY ( CRT:37GDA86X) AZ DY( CRT:CPJ370BVBK1UBC or CPJ370BVBK1S or A34JFQ90X) Degaussing Coil AK Magnet Ass'y AG -Purity and Static Convergence Wedge (Gum),Yoke AC Groundsing strap AD Spring for CRT AC TUNER NOTE:THE PARTS HERES SHOWN ARE SUPPLIED AS AN ASSEMBLY NOT INDEPENEDTLY. å TU51 VTUVTST6UF78/ J Tuner BD INTEGRATED CIRCUITS IC101 VHiKA78S05P-1 or VHiTA7805S/-1 çå C201 RH-iX2933CEZZ IC351 VHiTDA7233/-1 å IC501 VHiTA8403K/-1 çå IC701 VHiSTR301301E å IC751 VHiKA7809Pi-1 or VHiTA7809S/-1 å IC761 VHiKA7812Pi-1 or VHiTA7812S/-1 IC2001 RH-iX3087CEZZ IC2040 VHiPST994C/-1 IC2101 RH-iX2447CEN1 or RH-iX2448CEN1 J KiA78S05P AD J J J J R AX AF AL AP AE TA1268N TdA7233 TA8403K I.C. KiA7809Pi R KiA7812Pi J I.C. J PSt994C J ST24C01B6 AE AV AD AL TRANSISTORS PRINTED WIRING BOARD ASSEMBLIES PWB-A DUNTK9529WEV0 PWB-A DUNTK9529WEV4 PWB-B DUNTK9530WEV0 _ _ _ MAIN Unit (13K-M100/150) _ MAIN Unit (CK13M10/15) _ CRT Unit _ 23 Description Code Ref. No. å MAIN Unit (Continued) å Q602 VS2SD2586//1E or VS2SD2095//1E Q603 VS2SC945AQ/-1 or VS2SC1815YW-1 or VS2SC3198AQ/-1 Q752 VS2SC945AQ/-1 Q753 VS2SA1013//1E Q2001 VS2SD601AR/-1 Q2002 VS2SD601AR/-1 Q2060 VS2SD601AR/-1 J 2SD2586 AM J 2SC945 AB J J J J J AB AD AC AC AC You can substitute "VS2SD601AR/-1" for "VS2SC2462-C-1". Q201 VS2SC2735//1E J 2SC2735 AC Q351 VS2SD601AR/-1 J 2SD601 AC Q401 VS2SD601AR/-1 J 2SD601 AC Q403 VS2SD601AR/-1 J 2SD601 AC Q404 VS2SB709AR/-1 J 2SB709 AC Q451 VS2SB709AR/-1 J 2SB709 AC Q501 VS2SD601AR/-1 J 2SD601 AC Q601 VS2SC2655Y/-1 J 2SC2655 AE ★ Part No. D762 RH-DX0441CEZZ or RH-DX0110CEZZ D763 VHD1SS119//-1 D901 RH-EX0630GEZZ D902 RH-EX0630GEZZ D2001 VHD1SS119//-1 Description Code J Diode AC J J J J AB AA AA AB Diode Zener Diode Zener Diode Diode PACKAGED CIRCUITS 2SC945 2SA1013 2SD601 2SD601 2SD601 å You can substitute "RH-DX-446CEZZ" for "VHD1SS119//-1" and "RHDX0045GEZZ". D51 RH-EX0611GEZZ J Zener Diode AA D52 RH-EX0676GEZZ J Zener Diode AA or RH-EX0701GEZZ D53 RH-EX0611GEZZ J Zener Diode AA D401 VHD1SS119//-1 J Diode AB D402 RH-EX0092CEZZ J Zener Diode AB D454 RH-EX0103CEZZ J Zener Diode AB D455 VHD1SS119//-1 J Diode AB D501 RH-DX0441CEZZ J Diode AC or RH-DX0110CEZZ å D502 RH-DX0131CEZZ J Diode AC D601 RH-DX0441CEZZ J Diode AC or RH-DX0110CEZZ D603 RH-DX0441CEZZ J Diode AC or RH-DX0110CEZZ D610 RH-DX0131CEZZ J Diode AC D631 RH-EX0630GEZZ J Zener Diode AA D641 RH-EX0630GEZZ J Zener Diode AA çå D651 RH-DX0131CEZZ J Diode AC çå D652 VHD1SS119//-1 J Diode AB çå D653 RH-EX0091CEZZ J Zener Diode AB or RH-EX0660GEZZ or RH-EX1311CEZZ å D661 RH-DX0444CEZZ J Diode AH å D701 RH-DX0154CEZZ J Diode AC å D702 RH-DX0154CEZZ J Diode AC å D703 RH-DX0154CEZZ J Diode AC å D704 RH-DX0154CEZZ J Diode AC D753 VHD1SS119//-1 J Diode AB D754 VHD1SS119//-1 J Diode AB D755 RH-DX0441CEZZ J Diode AC or RH-DX0110CEZZ å D756 RH-DX0441CEZZ J Diode AC or RH-DX0110CEZZ D757 VHD1SS119//-1 J Diode AB D758 RH-DX0131CEZZ J Diode AC å D760 RH-DX0441CEZZ J Diode AC or RH-DX0110CEZZ å D761 RH-DX0441CEZZ J Diode AC or RH-DX0110CEZZ PR701 RMPTP0026CEZZ X801 RCRSB0001PEZZ or RCRSB0205CEZZ J Packaged Circuit R Crystal AF AL FILTERS CF301 RFiLC0403CEZZ or RFiLC0029TAZZ CF401 RFiLC0013CEZZ or RFiLC0004PEZZ CF631 RFiLA0034CEZZ CF2040 RFiLC0121GEZZ DIODES in CANADE: Contact SHARP Electronics of Conada Limited Phone (416) 890-2100 ç PICTURE TUBE ç åV101 2. NO. DE REF ★MARQUE: SECTION LIVRAISON DES PIECES DE RECHANGE MARKç : X- RAY RELATED PARTS Part No. "COMMENT COMMANDER LES PIECES DE RECHANGE" 1. NUMERO DU MODELE ★ Part No. DUNTK9529WEV0/V4 Pour que votre commande soit rapidement et correctement remplie, veuillez fournir les renseignements suivants. Contact your nearest SHARP Parts Distributor to order. For location of SHARP Parts Distributor, Please call Toll-Free; 1-800-BE-SHARP Ref. No. Ref. No. J Filter AE J Filter AE J Filter J Filter AD AD COILS å L201 VP-XF1R2K0000 L202 RCiLi0612CEZZ or RCiLi0588CEZZ L301 VP-XF8R2K0000 L302 RCiLi0613CEZZ or RCiLi0605CEZZ L401 VP-XF120K0000 L402 VP-XF100K0000 L406 VP-XF680K0000 L408 VP-XF100K0000 L701 RCiLF0029PEZZ or RCiLF0087CEZZ or RCiLF0235CEZZ or RCiLF0090CEZZ L2040 RCiLB0159CEZZ SF201 RFiLC0405CEZZ J Peaking 1.2µH J If Coil AB AE J Peaking 8.2µH J If Coil AB AE J J J J R AB AB AB AB AH Peaking 12µH Peaking 10µH Peaking 68µH Peaking 10µH Coil J Oscillation Coil J Filter AE AH TRANSFORMERS å çå å T601 T602 or T701 or RTRNZ0168CEZZ RTRNF0151PEZZ RTRNF0148PEZZ RTRNP0527CEZZ RTRNP0518CEZZ C51 C52 C53 C54 C55 C201 C202 C203 C204 C205 VCEA0A1CW476M VCSATA1CE226K VCEA0A1HW105M VCEA0A1HW475M VCEA0A1CW477M VCKYCY1HF103Z VCKYPA1HF103Z VCKYCY1HF103Z VCKYCY1HF103Z VCEA0A1HW474M J H-Driver R H-out AH BE J Power AM CAPACITORS 24 J J J J J J J J J J 47 22 1.0 4.7 470 0.01 0.01 0.01 0.01 0.47 16V 16V 50V 50V 16V 50V 50V 50V 50V 50V EL. Tantalum EL. EL. EL. Ceramic Ceramic Ceramic Ceramic EL. AB AD AB AB AC AA AA AA AA AB 13K-M100/150 CK13M10/15 Ref. No. Part No. ★ Description Code Ref. No. DUNTK9529WEV0/V4 MAIN Unit (Continued) C206 C207 C208 C209 C210 C302 C303 C304 C305 C306 C308 C309 C312 C314 C351 C352 C353 C354 C355 C361 C362 C403 C404 C405 C406 C407 C408 C409 C410 C411 C413 C414 C419 C420 C451 C454 C502 C504 C505 C507 C508 C509 C510 C511 C513 C514 C517 C522 C551 C552 C604 çå C608 C609 VCEA0A1CW227M VCKYCY1HF103Z VCEA0A1HW474M VCKYCY1HB222K VCKYCY1HB102K VCCCCY1HH330J VCKYCY1HB472K VCEA0A1HW225M VCKYPA1HB151K VCKYPA1HF103Z VCKYCY1HB102K VCEA0A1CW227M VCKYCY1HF103Z VCEA0A1HW225M VCKYCY1HB562K VCEA0A1CW107M VCEA0A1CW337M RC-QZA104TAYK VCEA0A1CW226M VCEA0A1CW477M VCEA0A1CW476M VCCCCY1HH101J VCCCCY1HH680J VCEA0A1HW335M VCEA0A1HW335M RC-QZA104TAYK VCEA0A1CW106M VCEA0A1HW105M VCKYCY1EF104Z VCEAGA1CW108M VCKYCY1HF103Z VCKYCY1EF104Z VCCCCY1HH330J VCCCCY1HH471J RC-QZA563TAYK VCEA0A1HW475M VCEA0A1EW477M VCKYPA2HB391K VCQYTA1HM473K VCKYPA1HB102K VCEAGA1VW107M VCKYPA2HB102K VCEAGA1VW477M VCQYTA1HM473K VCEACA1HC225M VCEACA1HC335J VCKYCY1HB102K VCKYCY1HF103Z VCSATA1CE225K VCEA0A1HW225M VCEA0A1CW227M VCFPPD3CA522H RC-QZA223TAYK J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 220 16V EL. 0.01 50V Ceramic 0.47 50V EL. 2200p 50V Ceramic 1000p 50V Ceramic 33p 50V Ceramic 4700p 50V Ceramic 2.2 50V EL. 150p 50V Ceramic 0.01 50V Ceramic 1000p 50V Ceramic 220 16V EL. 0.01 50V Ceramic 2.2 50V EL. 5600p 50V Ceramic 100 16V EL. 330 16V EL. 0.1 50V Mylar 22 16V EL. 470 16V EL. 47 16V EL. 100p 50V Ceramic 68p 50V Ceramic 3.3 50V EL. 3.3 50V EL. 0.1 50V Mylar 10 16V EL. 1.0 50V EL. 0.1 25V Ceramic 1000 16V EL. 0.01 50V Ceramic 0.1 25V Ceramic 33p 50V Ceramic 470p 50V Ceramic 0.056 50V Mylar 4.7 50V EL. 470 25V EL. 390p 500V Ceramic 0.047 50V Mylar 1000p 50V Ceramic 100 35V EL. 1000p 500V Ceramic 470 35V EL. 0.047 50V Mylar 2.2 50V EL. 3.3 50V EL. 1000p 50V Ceramic 0.01 50V Ceramic 2.2 16V Tantalum 2.2 50V EL. 220 16V EL. 5200p 1600V Metal.Poly.Film 0.022 50V Mylar AC AA AB AA AA AA AA AB AA AA AA AC AA AB AA AC AC AB AB AC AB AA AA AB AB AB AB AB AA AD AA AA AA AA AB AB AD AA AB AA AC AA AD AB AC AC AA AA AB AB AC AE AB å å å å å 25 Part No. C612 VCFPPB2EB334J C631 VCEA0A1HW225M C632 VCKYCY1HF103Z C633 VCEA0A1HW105M C652 VCEA0A1HW475M C653 VCEA0A1CW106M C661 VCKYPA2HB152K C662 VCEA0A1CW477M C701 RC-FZ015SCEZZ or RC-FZ002SCEZZ or RC-FZ004SGEZZ or RC-FZ027CUMZZ or RC-FZ059SCEZZ or RC-FZ0279CEZZ C702 VCKYPB2HE103P C703 VCKYPB2HE103P C704 VCKYPB2HE103P C705 RC-EZ0422CEZZ or RC-EZ0522CEZZ C706 RC-KZ0092GEZZ or RC-KZ0311CEZZ C707 VCEAGA2CW226M C712 RC-EZ0638CEZZ or RC-EZ0658CEZZ C751 VCEA0A1VW477M C754 VCEA0A1CW337M C755 VCEA0A1CW107M C756 VCEAGA1CW108M C757 RC-QZA104TAYK C758 VCEAGA2EW106M C759 VCKYPA2HB102K C760 VCEAGA1CW108M C801 RC-QZA223TAYK C802 VCEA0A1HW474M C803 VCCCCY1HH120J C804 VCEA0A1HW104M C805 VCEA0A1HW104M C806 VCEA0A1HW104M C807 VCCCCY1HH820J C901 VCKYCY1EF104Z C905 VCEA0A1HW335M C2001 VCCCCY1HH101J C2002 VCCCCY1HH101J C2021 VCCCCY1HH101J C2022 VCCCCY1HH101J C2023 VCCCCY1HH101J C2024 VCCCCY1HH101J C2040 VCEA0A1AW107M C2041 VCEA0A1HW105M C2051 VCCCCY1HH101J C2060 RC-QZA104TAYK C2061 VCKYD41HB101K C2062 VCEA0A1AW107M C2402 VCCCCY1HH560J C2601 VCEA0A1HW475M C2602 VCCCCY1HH101J ★ Description Code J J J J J J J J J 0.33 2.2 0.01 1.0 4.7 10 1500p 470 250V 50V 50V 50V 50V 16V 500V 16V Metal.Poly.FilmAF EL. AB Ceramic AA EL. AB EL. AB EL. AB Ceramic AA EL. AC AE J J J J 0.01 0.01 0.01 470 500V 500V 500V 200V Ceramic Ceramic Ceramic EL. AB AB AB AN J 0.0033 AC125V Ceramic AC J 22 J 33 160V EL. 160V EL. AD AG J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 35V 16V 16V 16V 50V 250V 500V 16V 50V 50V 50V 50V 50V 50V 50V 25V 50V 50V 50V 50V 50V 50V 50V 10V 50V 50V 50V 50V 10V 50V 50V 50V AB AC AC AD AB AC AA AD AB AB AA AB AB AB AA AA AB AA AA AA AA AA AA AB AB AA AB AA AB AA AB AA 470 330 100 1000 0.1 10 1000p 1000 0.022 0.47 12p 0.1 0.1 0.1 82p 0.1 3.3 100p 100p 100p 100p 100p 100p 100 1.0 100p 0.1 100p 100 56p 4.7 100p EL. EL. EL. EL. Mylar EL. Ceramic EL. Mylar EL. Ceramic EL. EL. EL. Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. EL. Ceramic Mylar Ceramic EL. Ceramic EL. Ceramic 13K-M100/150 CK13M10/15 Ref. No. ★ Part No. Description Code Ref. No. DUNTK9529WEV0/V4 MAIN Unit (Continued) RESISTORS å å å RJ1 RJ3 RJ5 RJ6 RJ7 RJ9 RJ10 RJ12 RJ15 RJ17 RJ18 RJ19 RJ20 RJ21 RJ23 RJ24 RJ26 RJ30 RJ31 RJ32 RJ35 RJ40 RJ47 RJ49 RJ52 RJ55 RJ57 RJ59 RJ62 RJ63 RJ66 RJ67 RJ68 RJ71 RJ75 RJ77 RJ78 RJ79 R51 R52 R53 R54 R55 R56 R57 R201 R202 R203 R204 R205 R206 R208 VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRS-VV3AB331J VRS-VV3DB470J VRS-VV3LB223J VRN-MD2AL101J VRN-MD2AL101J VRN-MD2AL823J VRN-MD2AL392J VRN-MD2AL221J VRN-MD2AL122J VRD-RA2BE682J VRN-MD2AL270J VRD-RA2BE391J VRD-RA2EE151J VRN-MD2AL391J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 330 47 22k 100 100 82k 3.9k 220 1.2k 6.8k 27 390 150 390 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 1W 2W 3.0W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 1/8W 0.1W 1/8W 1/4W 0.1W Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Oxide Metal.Oxide Metal.Oxide Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Carbon Metal.Film Carbon Carbon Metal.Film AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA å å AA AA AA AA AA å 26 R301 R302 R303 R307 R352 R353 R354 R361 R364 R401 R403 R404 R407 R409 R410 R411 R412 R413 R414 R415 R416 R417 R418 R419 R423 R426 R440 R451 R452 R454 R455 R456 R457 R458 R459 R504 R505 R506 R507 R508 R510 R511 R512 R516 R517 R518 R524 R525 R552 R553 R554 R555 R556 R602 R603 R605 Part No. ★ VRD-RA2BE222J VRN-MD2AL102J VRN-MD2AL153J VRN-MD2AL333J VRN-MD2AL332J VRN-MD2AL4R7J VRN-MD2AL152J VRD-RA2BE102J VRN-MD2AL473J VRN-MD2AL682J VRD-RA2BE331J VRN-MD2AL391J VRN-MD2AL471J VRN-MD2AL471J VRD-RA2BE563J VRN-MD2AL103J VRD-RA2EE561J VRD-RA2BE470J VRD-RA2BE470J VRD-RA2BE470J VRN-MD2AL102J VRD-RA2BE101J VRN-MD2AL152J VRN-MD2AL472J VRN-MD2AL222J VRN-MD2AL271J VRN-MD2AL821J VRS-SV2HC103J VRD-RA2BE152J VRD-RA2BE334J VRD-RA2BE392J VRN-MD2AL223J VRD-RA2BE102J VRD-RA2BE564J VRD-RA2BE123J VRD-RA2BE471J VRN-MD2AL101J VRD-RA2BE683G VRD-RA2BE104G VRD-RA2BE473J VRD-RM2HD1R5J VRN-SV2HB3R9J VRD-RM2HD681J VRD-RA2BE223G VRD-RA2BE103G VRD-RA2BE154J VRN-MD2AL332J VRD-RA2BE473J VRD-RA2BE102J VRN-MD2AL273J VRN-MD2AL472J VRN-MD2AL102J VRN-MD2AL102J VRD-RA2EE820J VRS-VV3LB270J VRN-MD2AL332J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 2.2k 1.0k 15k 33k 3.3k 4.7 1.5k 1.0k 47k 6.8k 330 390 470 470 56k 10k 560 47 47 47 1.0k 100 1.5k 4.7k 2.2k 270 820 10k 1.5k 330k 3.9k 22k 1.0k 560k 12k 470 100 68k 100k 47k 1.5 3.9 680 22k 10k 150k 3.3k 47k 1.0k 27k 4.7k 1.0k 1.0k 82 27 3.3k 1/8W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 1/8W 0.1W 0.1W 1/8W 0.1W 0.1W 0.1W 1/8W 0.1W 1/4W 1/8W 1/8W 1/8W 0.1W 1/8W 0.1W 0.1W 0.1W 0.1W 0.1W 1/2W 1/8W 1/8W 1/8W 0.1W 1/8W 1/8W 1/8W 1/8W 0.1W 1/8W 1/8W 1/8W 1/2W 1/2W 1/2W 1/8W 1/8W 1/8W 0.1W 1/8W 1/8W 0.1W 0.1W 0.1W 0.1W 1/4W 3.0W 0.1W Carbon Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Carbon Metal.Film Metal.Film Carbon Metal.Film Metal.Film Metal.Film Carbon Metal.Film Carbon Carbon Carbon Carbon Metal.Film Carbon Metal.Film Metal.Film Metal.Film Metal.Film Metal.Film Metal.Oxide Carbon Carbon Carbon Metal.Film Carbon Carbon Carbon Carbon Metal.Film Carbon Carbon Carbon Carbon Metal.Film Carbon Carbon Carbon Carbon Metal.Film Carbon Carbon Metal.Film Metal.Film Metal.Film Metal.Film Carbon Metal.Oxide Metal.Film Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AB AA 13K-M100/150 CK13M10/15 Ref. No. Part No. ★ Description Code Ref. No. DUNTK9529WEV0/V4 R2009 VRN-MD2AL102J R2010 VRN-MD2AL102J R2011 VRN-MD2AL821J R2012 VRN-MD2AL471J R2020 VRD-RM2HD223J R2022 VRD-RA2BE333J R2024 VRD-RA2BE682J R2025 VRD-RA2BE682J R2026 VRD-RA2BE682J R2027 VRD-RA2BE682J R2028 VRD-RA2BE102J R2029 VRN-MD2AL102J R2031 VRN-MD2AL103J R2032 VRN-MD2AL471J R2040 VRN-MD2AL102J R2041 VRN-MD2AL333J R2042 VRN-MD2AL101J R2043 VRN-MD2AL101J R2044 VRN-MD2AL683J R2045 VRN-MD2AL101J R2047 VRN-MD2AL221J R2048 VRD-RA2BE562J R2049 VRN-MD2AL333J R2054 VRN-MD2AL222J R2055 VRN-MD2AL103J R2060 VRN-MD2AL221J R2061 VRN-MD2AL562J R2062 VRN-MD2AL183J R2063 VRD-RA2BE222J R2064 VRD-RA2BE332J R2066 VRN-MD2AL103J R2067 VRN-MD2AL103J R2068 VRN-MD2AL103J R2070 VRN-MD2AL103J R2101 VRN-MD2AL101J R2102 VRN-MD2AL101J R2401 VRN-MD2AL101J R2402 VRN-MD2AL101J R2403 VRN-MD2AL101J R2404 VRN-MD2AL101J R2501 VRN-MD2AL123J R2503 VRN-MD2AL273J R2504 VRN-MD2AL123J R2505 VRN-MD2AL563J R2506 VRN-MD2AL563J R2507 VRN-MD2AL823J R2508 VRN-MD2AL153J R2509 VRN-MD2AL272J R2601 VRD-RA2BE331J MAIN Unit (Continued) å R606 R608 R609 R610 R620 R621 R631 R632 R633 R634 R641 R642 R651 R654 R655 R656 R659 R661 R701 VRD-RA2BE102J VRD-RA2BE101J VRD-RA2BE331J VRS-VV3DB391J VRD-RA2BE473J VRN-MD2AL682J VRN-MD2AL391J VRN-MD2AL152J VRN-MD2AL472J VRD-RM2HD121J VRS-VV3AB682J VRD-RA2BE821J VRD-RM2HD1R0J VRD-RA2BE154J VRN-MD2AL104J VRN-MD2AL333J VRN-VV3AB1R8J VRN-VV3ABR47J VRC-UA2HG275K J J J J J J J J J J J J J J J J J J J å R701 VRC-UB2HG275K J å R702 VRW-KP3HC1R8K R703 VRS-KA3NG561J R704 VRD-RM2HD123J R705 VRD-RA2EE334J R706 VRD-RM2HD470J R707 VRN-VV3DB1R5J R708 VRD-RM2HD824J R709 VRS-KA3NG561J R717 VRS-KA3HG3R3K R730 VRS-VV3DB270J R750 VRS-VV3AB561J R752 VRD-RA2BE562J R754 VRN-MD2AL471J R755 VRS-VV3DB470J R757 VRN-MD2AL472J R758 VRS-SV2HC150J R801 VRN-MD2AL332J R802 VRN-MD2AL332J R803 VRN-MD2AL182J R804 VRN-MD2AL182J R805 VRN-MD2AL182J R806 VRN-MD2AL333J R902 VRN-MD2AL750J R906 VRN-MD2AL102J R925 VRN-MD2AL104J R961 VRN-MD2AL101J R962 VRN-MD2AL101J R2001 VRD-RA2BE102J R2002 VRN-MD2AL103J R2006 VRN-MD2AL103J R2008 VRD-RA2BE224J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J å å çå çå çå çå å å å å å å å å å å 1.0k 1/8W Carbon 100 1/8W Carbon 330 1/8W Carbon 390 2W Metal.Oxide 47k 1/8W Carbon 6.8k 0.1W Metal.Film 390 0.1W Metal.Film 1.5k 0.1W Metal.Film 4.7k 0.1W Metal.Film 120 1/2W Carbon 6.8k 1W Metal.Oxide 820 1/8W Carbon 1.0 1/2W Carbon 150k 1/8W Carbon 100k 0.1W Metal.Film 33k 0.1W Metal.Film 1.8 1W Metal.Film 0.47 1W Metal.Film 2.7M 1/2W Solid 13K-M100/150 2.7M 1/2W Solid CK13M10/15 1.8 5W Cement 560 7.0W Metal.Oxide 12k 1/2W Carbon 330k 1/4W Carbon 47 1/2W Carbon 1.5 2W Metal.Film 820k 1/2W Carbon 560 7.0W Metal.Oxide 3.3 5W Metal.Oxide 27 2W Metal.Oxide 560 1W Metal.Oxide 5.6k 1/8W Carbon 470 0.1W Metal.Film 47 2W Metal.Oxide 4.7k 0.1W Metal.Film 15 1/2W Metal.Oxide 3.3k 0.1W Metal.Film 3.3k 0.1W Metal.Film 1.8k 0.1W Metal.Film 1.8k 0.1W Metal.Film 1.8k 0.1W Metal.Film 33k 0.1W Metal.Film 75 0.1W Metal.Film 1.0k 0.1W Metal.Film 100k 0.1W Metal.Film 100 0.1W Metal.Film 100 0.1W Metal.Film 1.0k 1/8W Carbon 10k 0.1W Metal.Film 10k 0.1W Metal.Film 220k 1/8W Carbon Part No. AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AF AC AF AA AA AA AB AA AF AD AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA ★ Description Code J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 1.0k 0.1W Metal.Film 1.0k 0.1W Metal.Film 820 0.1W Metal.Film 470 0.1W Metal.Film 22k 1/2W Carbon 33k 1/8W Carbon 6.8k 1/8W Carbon 6.8k 1/8W Carbon 6.8k 1/8W Carbon 6.8k 1/8W Carbon 1.0k 1/8W Carbon 1.0k 0.1W Metal.Film 10k 0.1W Metal.Film 470 0.1W Metal.Film 1.0k 0.1W Metal.Film 33k 0.1W Metal.Film 100 0.1W Metal.Film 100 0.1W Metal.Film 68k 0.1W Metal.Film 100 0.1W Metal.Film 220 0.1W Metal.Film 5.6k 1/8W Carbon 33k 0.1W Metal.Film 2.2k 0.1W Metal.Film 10k 0.1W Metal.Film 220 0.1W Metal.Film 5.6k 0.1W Metal.Film 18k 0.1W Metal.Film 2.2k 1/8W Carbon 3.3k 1/8W Carbon 10k 0.1W Metal.Film 10k 0.1W Metal.Film 10k 0.1W Metal.Film 10k 0.1W Metal.Film 100 0.1W Metal.Film 100 0.1W Metal.Film 100 0.1W Metal.Film 100 0.1W Metal.Film 100 0.1W Metal.Film 100 0.1W Metal.Film 12k 0.1W Metal.Film 27k 0.1W Metal.Film 12k 0.1W Metal.Film 56k 0.1W Metal.Film 56k 0.1W Metal.Film 82k 0.1W Metal.Film 15k 0.1W Metal.Film 2.7k 0.1W Metal.Film 330 1/8W Carbon AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA MISCELLANEOUS PARTS S2501 QSW-K0079GEZZ S2502 QSW-K0079GEZZ S2503 QSW-K0079GEZZ S2504 QSW-K0079GEZZ S2505 QSW-K0079GEZZ 27 J J J J J Switch, Power Switch, Vol-down Switch, Vol-up Switch, CH-down Switch, CH-up AB AB AB AB AB 13K-M100/150 CK13M10/15 Ref. No. ★ Part No. Description Code Ref. No. MAIN Unit (Continued) MISCELLANEOUS PARTS RY701 RRLYU0036CEZZ J or RRLYU0038CEZZ or RRLYJ0077CEZZ å F701 QFS-B4023CEZZ J or QFS-B4021GEZZ FB602 RBLN-0037CEZZ J FB603 RBLN-0037CEZZ J FH701 QFSHD1013CEZZ J FH702 QFSHD1014CEZZ J J903 QJAKE0159CEZZ J J905 QJAKE0158CEZZ J P302 QPLGN0261CEZZ J P401 QPLGN0561CEZZ J P601 QPLGN0603CEZZ J P651 QPLGN0361CEZZ J P701 QPLGN0207CEZZ J P751 QPLGN0461CEZZ J P2001 QPLGN0561CEZZ J RMC2601 RRMCU0227CEZZ J or RRMCU0222CEZZ RDA501 PRDAR0218PEFW R RDA701 PRDAR0237PEFW R TP701 QLUGP0102PEZZ R PZETM0016CEZZ J Relay AM Fuse AC Balun Balun Fuse Holder Fuse Holder Jack Jack Plug Plug Plug Plug Plug Plug Plug Remote Receiver AB AB AC AC AF AF AB AB AB AB AA AB AB AK Heat Sink Heat Sink Lug Insulator AD AK AA AA å å å J J J J SP1 VSP0080PBK58A ACC701 QACCD3038CESA or QACCD3051CESA or QACCD3037CESA or QACCD3056CESA or QACCD3055CESA å ACC701 QACCD3037CESB or QACCD3055CESB QCNW-2105PEZZ QCNW-2106PEZZ QCNW-2107PEZZ QANTR0022PEZZ 2SC2229 (O) 2SC2229 (O) 2SC2229 (O) 2SA1266 (Y) å AD AD AD AA DIODES COILS AND CAPACITORS VP-DF151K0000 VCCCCY1HH271J VCCCCY1HH271J VCCCCY1HH271J RC-KZ0016CEZZ VCEA0A1CW106M VCEA0A1CW336M J J J J J J J VRN-MD2AL470J VRD-RA2BE271J VRN-MD2AL121J VRS-VV3AB123J VRD-RM2HD332J VRN-MD2AL470J VRD-RA2BE271J VRN-MD2AL121J VRS-VV3AB123J VRD-RM2HD332J VRD-RA2BE470J VRN-MD2AL271J VRN-MD2AL121J VRS-VV3AB123J VRD-RM2HD332J VRN-MD2AL561J VRN-MD2AL391J VRD-RA2BE561J VRN-MD2AL152J VRN-MD2AL431J VRN-MD2AL470J J J J J J J J J J J J J J J J J J J J J J 47 270 120 12k 3.3k 47 270 120 12k 3.3k 47 270 120 12k 3.3k 560 390 560 1.5k 430 47 0.1W 1/8W 0.1W 1W 1/2W 0.1W 1/8W 0.1W 1W 1/2W 1/8W 0.1W 0.1W 1W 1/2W 0.1W 0.1W 1/8W 0.1W 0.1W 0.1W Metal.Film Carbon Metal.Film Metal.Oxide Carbon Metal.Film Carbon Metal.Film Metal.Oxide Carbon Carbon Metal.Film Metal.Film Metal.Oxide Carbon Metal.Film Metal.Film Carbon Metal.Film Metal.Film Metal.Film AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA Peaking 150µH 270p 50V Ceramic 270p 50V Ceramic 270p 50V Ceramic 0.01 1.4kV Ceramic 10 16V Electrolytic 33 16V Electrolytic J Plug J Plug J CRT Socket AB AB AK MISCELLANEOUS PARTS You can substitute "RH-DX-446CEZZ" for "VHD1SS119//-1" and "RHDX0045GEZZ". D881 VHD1SS119//-1 J Diode AB D882 VHD1SS119//-1 J Diode AB D885 VHD1SS119//-1 J Diode AB L851 C851 C852 C853 C854 C881 C883 Code MISCELLANEOUS PARTS TRANSISTORS VS2SC2229O/1E VS2SC2229O/1E VS2SC2229O/1E VS2SA1266-Y-1 VS2SA1015-Y-1 R851 R852 R853 R857 R858 R859 R860 R861 R865 R866 R867 R868 R869 R873 R874 R881 R882 R883 R884 R886 R887 P851 QPLGN0561CEZZ P852 QPLGN0461CEZZ SC851 QSOCV0839CEZZ or QSOCV0829CEZZ DUNTK9530WEV0 CRT Unit Q852 Q854 Q856 Q881 or Description RESISTORS DUNTK9529WEV0/V4 å ★ Part No. AB AA AA AA AC AB AB 28 J Speaker AL AC Cord (13K-M100/CK13M10) AK AC Cord (13K-M150/CK13M15) AK R R R R Connecting Cord Connecting Cord Connecting Cord Rod Antenna AF AE AE AP 13K-M100/150 CK13M10/15 Ref. No. ★ Part No. Description Code Ref. No. R _ R R R Cabinet Ass'y,Front Cabinet Front Cover Button Cabinet AZ AD AE AW 13K-M150 1 1-1 1-2 1-3 2 CCABA2395WEV2 _ GCOVA0078PEKA JBTN-0258PESB GCABB2309PEKB R _ R R R Description RRMCG1324CESA R Infrared R-C (13K-M100/ CK13M10) RRMCG1324CESB R Infrared R-C (13K-M150 CK13M15) TGAN-0018PEZZ R Guarantee Card TiNS-6317PEZZ R Operation Manual (13KM100/150) TiNS-6353PEZZ R Operation Manual (CK13M10/15) 13K-M100 CCABA2395WEV0 _ GCOVA0078PEKA JBTN-0258PESA GCABB2309PEKA ★ Code SUPPLIED ACCESSORIES CABINET PARTS 1 1-1 1-2 1-3 2 Part No. Cabinet Ass'y,Front Cabinet Front Cover Button Cabinet AT AT AD AE AE AZ AD AR AW CK13M10 1 1-1 1-2 1-3 2 CCABA2409WEVO _ GCOVA0078PEKA JBTN-0258PESA GCABB2325PEKA R _ R R R Cabinet Ass'y,Front Cabinet Front Cover Button Cabinet AZ PACKING PARTS (NOT REPLACEMENT ITEM) AD AE AW SPAKC6303PEZZ SPAKC6319PEZZ SPAKC6323PEZZ SPAKC6339PEZZ SPAKP0031PEZZ SPAKP0110PEZZ SPAKX2630PEZZ SSAKA0001PEZZ CK13M15 1 1-1 1-2 1-3 2 CCABA2409WEV2 _ GCOVA0078PEKA JBTN-0258PESA GCABB2325PEKB R _ R R R Cabinet Ass'y,Front Cabinet Front Cover Button Cabinet AZ AD AE AW 1 1-2 1-1 1-3 29 _ Packing Case (13KM100) (13KM150) _ Packing Case (CK13M10) (CK13M15) _ Wrapping Paper _ Wrapping Paper _ Packing Add. _ Polyethylene Bag _ _ _ _ _ _ 13K-M100/150 CK13M10/15 Ref. No. Part No. ★ Description Code Ref. No. ★ Part No. Description Code PACKING OF THE SET ★ Polystyrene Bag Operation manual Guarantee Card and batteries ★Polystyrene mat ★ Buffer material FRONT ★ Packing case Use tapes to fix the packing case. REAR Printed in Japan TQ-0394-S 30 ">
Link pubblico aggiornato
Il link pubblico alla tua chat è stato aggiornato.