220-240V~ 50-60Hz 5946-A/C/D/E/H/N-3/5-544-XX 2. 5946-A/C/D/E/H/N-3/5-545-XX 3. 5946-A/C/D/E/H/N-3/5-676-XX 4. 5946-A/C/D/E/H/N-3/4-546-XX 5. 5946-A/C/D/E/H/N-3/4-547-XX 6. 5946-A/C/D/E/H/N-3/4-677-XX 7. Constant Voltage 24V (Output from SELV system 8. only) (¡ÃÐáÊ俵ͧÁÒ¨Ò¡Ãкºáç´Ñ¹ 9. ä¿¿ÒµèíÒ¾ÔàÈÉ¢Ñé¹»ÅÍ´ÀÑ 10. à¾Õ§à·Ò¹Ñé¹) 5946-A/C/D/E/H/N-7-654-XX 908 90° 90° 103 42 1. 1 42 Ordering Code 360° Input voltage 360° No. IP66 171 INSTALLATION MANUAL PRODUCT NAME : Mini ALPHA Square - Gear Arm Mini ALPHA Square - Gear Arm CVDA LED 13 W On-Off /Dim 1-10V/ DALI 900 5946-A/C/D/E/H/N-7-655-XX 130 90° 5946-A/C/D/E/H/N-7-678-XX 90° 103 LED 8.1 W On-Off/13 W(24V ) DALI CVDA 2 2.3 2.1 2.2 1-10 Light Emitting Diodes (LED) 4 3 LED 8.1W On-Off/13W(24Vdc) DALI CVDA Resin drill point. ¨Ø´à¨ÒÐàëԹ 4.2 3.2 4.3 Use a screwdriver to drill. The point at which the esin is completely released. ãªä¢¤Ç§à¾×èÍà¨ÒШش·Õèà·àëԹÍÍ¡ ¨¹ËÁ´ 3.1 Last Revised On : 20/05/2024 REV.05 1/6 4.1 FR-DD-29 REV.00 EFF 11/03/24 Cable size dia Ø12-13 mm. ¢¹Ò´ÊÒÂä¿ with washer. áËǹÃͧ 16.5 56 D L 6 6 LED 8.1 W On-Off/ 13 W(24V ) DALI CVDA 162 dia 11 mm. 13 L 38 mm. Make sure that cable glands are tightened. µÍ§¢Ñ¹à¤àºÔéÅá¡Å¹´ãËá¹¹·Ø¡¨Ø´ 30 Cable size : 3x1.00 mm.2 8-13 mm. ¢¹Ò´ÊÒÂä¿ L dia 13 mm. H Ø 4 mm. Ø 9 mm. 25 dia 9 mm. 11 D L Ø7 mm./ÁÁ. 37 mm./ÁÁ. DA2 DA2 Cable size dia Ø10-11 mm. ¢¹Ò´ÊÒÂä¿ with washer. áËǹÃͧ 9 D L DA1 24 Bush protected against dripping water. ºÙª»Í§¡Ñ¹¹éíÒ«ÖÁà¢ÒµÑÇâ¤Á LED 13 W On-Off Dim 1-10V/ DALI N N 16 L For On-Off For 1-10V dimming and DALI system. ÊíÒËÃѺÃкº´ÔÁ1-10V áÅÐÃкºDALI For DALI CVDA Green/Yellow : Brown : L Blue : N White : + Black : - A A = 38-40 mm. B = 8-10 mm. C = 30-32 mm. Cable Size/¢¹Ò´ÊÒÂä¿ : 5x1.00 mm.2 Ø8-13 mm. DA1 Cable size dia Ø8-9 mm. ¢¹Ò´ÊÒÂä¿ with washer. áËǹÃͧ Rubber seal size ÅÙ¡ÂÒ§à¤àºÔ Åá¡Åç¹´·Õè㪠Screw size ¢¹Ò´Ê¡ÃÙà¡ÅÕÂÇ»ÅÍ L Cable size : ¢¹Ò´ÊÒÂä¿ Wall plug anchor size ¢¹Ò´¾Ø¡½§¼¹Ñ§ H 44 Use the rubber seal according to the size of the cable. àÅ×͡㪠ÅÙ¡ÂÒ§à¤àºÔ Åá¡Åç¹´ µÒÁ¢¹Ò´¢Í§ÊÒÂä¿ D 5 B C N L For DALI System ÊíÒËÃѺÃкº DALI 1:+ DA2 2:- + 1...10V DA1 For Constant Voltage LED 24V (Remote driver) Warning Please ensure that the led lamp is connected to the driver correctly. Wrong polarity connection cause a damage to the led lamp and driver. â»Ã´ÃÐÇѧ¡ÒõÍÊÒÂä¿ÊÅѺ¢ÑéÇ +ºÇ¡ -ź ¨Ò¡ä´ÃàÇÍÃÁÒà¢Ò·ÕèËÅÍ´ LED ËÒ¡µÍÊÅѺ¢ÑéÇ ¨Ð·íÒãËä´ÃàÇÍÃáÅÐËÅÍ´ LED à¡Ô´¤ÇÒÁàÊÕÂËÒ Output/ÍÍ¡ 24 V Input/à¢Ò 220-240 V~ Luminaires 1-n ( Output from SELV system only) (¡ÃÐáÊ俵ͧÁÒ¨Ò¡Ãкºáç´Ñ¹ä¿¿Ò µèíÒ¾ÔàÈÉ¢Ñé¹»ÅÍ´ÀÑÂà¾Õ§à·Ò¹Ñé¹) + L AC N - 1 n 2 DC DALI DA Control DA Parallel wiring constant voltage Distance from luminaire to Driver ÃÐÂзҧ¨Ò¡µÑÇâ¤Á¶Ö§ ä´ÃàÇÍà Luminaire Wattage Maximum number of luminaires Conductor size / ¢¹Ò´ÊÒÂä¿ for parallel connection / ¨íҹǹâ¤Á㹡ÒõÍẺ¢¹Ò¹ 1.00 mm.2 1.50 mm.2 2.00 mm.2 Accessory available separately./ÍØ»¡Ã³àÊÃÔÁ¨íÒ˹ÒÂᡵҧËÒ¡ Ordering Code Product Name AUN-DRG-0027-00 LED Constant Voltage Driver 24Vdc 72W. AUN-DRG-0011-00 LED Constant Voltage Driver 24Vdc 150W. Last Revised On : 20/05/2024 REV.05 13 W 1-3 luminaires 30 m 50 m 65 m 13 W 1-6 luminaires 15 m 25 m 35 m 2/6 FR-DD-29 REV.00 EFF 11/03/24 6 7 6.2 6.1 6.3 Installation complete µÔ´µÑé§àÊÃç¨ÊÁºÙó Torque/áçºÔ´ : 1.0 Nm. How to adjust the aiming angle. ÇÔ¸Õ¡ÒûÃѺͧÈÒ For vertical aiming. ÊíÒËÃѺá¹ÇµÑé§ For horizontal aiming. ÊíÒËÃѺá¹Ç¹Í¹ Torque/áçºÔ´ : 1.0 Nm. Torque/áçºÔ´ : 1.0 Nm. Remark : ËÁÒÂà赯 1. Installation should be carried out by a qualified electrician in accordance with appropriate national wiring regulation. ¡ÒõԴµÑé§â¤Áä¿¿ÒáÅÐÍØ»¡Ã³ ¤ÇôíÒà¹Ô¹¡ÒÃâ´ÂªÒ§ä¿¿Ò ·ÕèÁÕ¤ÇÒÁÃÙáÅФÇÒÁªíÒ¹Ò­ 㹡ÒõԴµÑé§ÍØ»¡Ã³ä¿¿Ò â´Â੾ÒеÒÁÁÒµÃฐÒ¹¢Í§¡ÒÃä¿¿Ò 2. Disconnect the power before changing the lamp. »´ÊÇÔ·ªä¿·Ø¡¤ÃÑ駷Õèà»ÅÕè¹ËÅÍ´ä¿ 3. For Class1 luminaire, the installation must be completed with earthing. ÊíÒËÃѺâ¤Áä¿·ÕèÁ¡Õ Òûͧ¡Ñ¹ä¿¿ÒÃÑèÇÃдѺ1 ¡ÒõԴµÑ駵ͧµÍÊÒ´ԹµÒÁÁÒµÃฐÒ¹¤ÇÒÁ»ÅÍ´ÀѵͧµÍ ÊÒ´ԹµÒÁÁÒµÃฐÒ¹¤ÇÒÁ»ÅÍ´ÀÑ 4. Do not exceed the maximum wattage. ËÒÁãªËÅÍ´ä¿·ÕèÁÕ¢¹Ò´Çѵµà¡Ô¹¡ÇÒ·ÕèÃÐºØ ËÃ×ÍãªËÅÍ´¼Ô´»ÃÐàÀ· 5. Don't touch LED while maintaining or cleaning. ËÒÁÊÑÁ¼ÑÊËÅÍ´ LED ¢³ÐºíÒÃاÃÑ¡ÉÒ ËÃ×Í·íÒ¤ÇÒÁÊÐÍÒ´ Last Revised On : 20/05/2024 REV.05 Installation complete µÔ´µÑé§àÊÃç¨ÊÁºÙó Installation complete µÔ´µÑé§àÊÃç¨ÊÁºÙó Warning : ¢Í¤ÇÃÃÐÇѧ 1. The manufacturer will not be liable or held responsible for any incorrect installation, misuse or improper use and unauthorised modification to the fittings. Failure to comply with mentioned warning may cause serious damage or serious injury to persons, animals or objects. If any modification is required please consult your dealer for the details. ·Ò§¼Ù¼ÅÔµäÁÊÒÁÒöÃѺ¼Ô´ªÍºã¹¤ÇÒÁàÊÕÂËÒÂã´æ·Õèà¡Ô´¨Ò¡¡Òà µÔ´µÑé§äÁ¶¡Ù ÇÔ¸,Õ ãª§Ò¹¼Ô´»ÃÐàÀ·ËÃ×Í´Ñ´á»Å§µÑÇâ¤Áã¹·Ø¡¡Ã³Õ «Öè§ ÊÔ觼Դ»¡µÔàËÅÒ¹Õé ÍÒ¨·íÒãËà¡Ô´ÍѹµÃÒ¡Ѻ ¤¹ ÊÑµÇ ÊÔ觢ͧ ËÒ¡ÁÕ¢ÍʧÊÑÂËÃ×ÍÁÕ¤ÇÒÁµÍ§¡ÒûÃѺᵧµÑÇâ¤Á ãËàËÁÒÐÊÁ¡Ñº¡ÒÃ㪧ҹ ¡ÃسҵԴµÍµÑÇá·¹¨íÒ˹ÒÂËÃ×ͼټÅÔµ 2. Where damage has occured to the fittings, please make the replacement with standard parts before use. 㹡óշèÁÕ Õªé¹Ô Êǹ»ÃСͺã´à¡Ô´¤ÇÒÁàÊÕÂËÒ¡ÃسÒà»ÅÕ蹪Թé ÊǹãËÁ¡Í¹¡ÒÃ㪧ҹ·Ø¡¤ÃÑé§ à¾×èͤÇÒÁ»ÅÍ´ÀÑ 3/6 FR-DD-29 REV.00 EFF 11/03/24 For On-off System. ÊíÒËÃѺÃкºà»´-»´ Cable Size : 3x1.00 mm.2 Ø8-13 mm. In case the supply cable is exposed to sunlight use UV resistant cable. ¡Ã³Õ·ÕèÁÕ¡ÒõԴµÑé§â¤Á俹͡ÍÒ¤Òà ËÃ×Íâ¤Áä¿·ÕèÁÕ¡ÒÃá¼ÃѧÊÕÂÙÇÕ ÊÒÂ俵ͧÊÒÁÒö»Í§¡Ñ¹ ËÃ×Í ÁÕ¡Òûͧ¡Ñ¹äÁã˶¡Ù ÃѧÊÕÂÙÇÕä´ Do not touch the LED because it may shorten the life time or the LED can be breaking down. ËÒÁÊÑÁ¼ÑÊËÅÍ´ LED â´Âà´ç´¢Ò´ à¾ÃÒШзíÒãËËÅÍ´àÊ×èÍÁÊÀÒ¾ NO Minimum distance to lighted surface. ÃÐÂÐËÒ§¢Ñé¹µèíÒ ¨Ò¡Ë¹Òâ¤Á¶Ö§¾×é¹¼ÔÇ·Õ趡٠ÊͧÊÇÒ§ 0.5 m The luminaire should be positioned so that prolonged staring into the luminaire at a distance closer than 0.5m in not expected. µíÒá˹§·ÕèµÔ´µÑ駴ǧâ¤Á¤ÇÃÍÂÙ㹨ش·ÕèáʧäÁÊͧà¢Ò´Ç§µÒâ´ÂµÃ§à»¹àÇÅÒ¹Ò¹ ËÒ¡à¢Òã¡Åã¹ ÃÐÂйÍ¡ÇÒ 0.5 Á. Any damaged safety glass cover must be replaced only with the original spare part. àÁ×èÍ¡ÃШ¡à¡Ô´¤ÇÒÁàÊÕÂËÒ à¾×èͤÇÒÁ»ÅÍ´ÀѤÇÃÊÑè§ÍÐäËÅá·¨Ò¡¼Ù¼ÅÔµà·Ò¹Ñé¹ Make sure the plug is secured tightly and note the ground level. ¾ÅØ¡µÍ§ÂÖ´ÍÂҧṹ˹ÒáÅÐàÊÁ͡Ѻ¼ÔǾ×é¹ Not using chemical compounds and aggressive agents such as , weed repellents fertilizers , acid solvent and contaminated irrigation water near the Luminaires. ËÒÁãªÊÒÃà¤ÁÕહ »ØÂ, ÂÒ¡íҨѴÈѵÃپת, »Ù¹¢ÒÇ, ÊÒÃÅÐÅÒ·Õè໹¡Ã´ áÅйéíÒ»¹à»Í¹ÊÒÃà¤ÁÕ ºÃÔàdz·ÕèµÔ´µÑé§â¤Áä¿ NO To reduce the risk of being constricted The wires attached to this lamp must be effectively fixed to the wall. if the power cord is within reach. à¾×èÍÅ´¤ÇÒÁàÊÕ觵͡Òö١ÊÒÂä¿à¡ÕèÂÇ/ÃÑ´ ÊÒÂä¿·ÕèµÍà¢ÒµÑÇâ¤ÁµÍ§¶Ù¡µÔ´ÂÖ´¡Ñº¼¹Ñ§ÍÂÒ§àÃÕºÃÍ Cable Cable Last Revised On : 20/05/2024 REV.05 4/6 FR-DD-29 REV.00 EFF 11/03/24 Our products are installed with electronic components with the protection against overvoltage according to IEC 61547. The customers have to install the additional overvoltage protection devices (against surge, transients, etc) in their electrical system to avoid the risk of damage. Failing to do so will end the product warranty. ¼ÅÔµÀѳ±¢Í§àÃÒÁÕ¡ÒõԴµÑé§ÍØ»¡Ã³ÍÔàÅç¡·Ã͹ԡÊÊíÒËÃѺ¡Òûͧ¡Ñ¹áç´Ñ¹ä¿à¡Ô¹µÒÁÁÒµÃฐÒ¹ IEC 61547 áÅÐÅÙ¡¤ÒµÍ§µÔ´µÑé§ÍØ»¡Ã³»Í§¡Ñ¹áç´Ñ¹ä¿à¡Ô¹à¾ÔèÁàµÔÁ (»Í§¡Ñ¹ä¿¡ÃЪҡ ,ä¿¿ÒÅѴǧ¨Ã ÏÅÏ)ã¹Ãкºä¿¿Ò´Ç à¾×èÍËÅÕ¡àÅÕ觤ÇÒÁàÊÕ觷Õè¨Ðà¡Ô´¤ÇÒÁàÊÕÂËÒ ËÒ¡äÁ´íÒà¹Ô¹¡Òôѧ¡ÅÒÇ ¡ÒÃÃѺ»ÃСѹ¨ÐÊÔé¹Êشŧ LED NO Do not use a high pressure washer to clean the products. ËÒÁãªà¤Ã×èͧ©Õ´¹éíÒáç´Ñ¹Ê٧㹡Ò÷íÒ¤ÇÒÁÊÐÍÒ´¼ÅÔµÀѳ± NO LED Clean the products regularly to maintain good light output and prolong surface quality . Only use solvent-free cleaning solutions on the products. ·íÒ¤ÇÒÁÊÐÍÒ´¼ÅÔµÀѳ±à»¹»ÃШíÒà¾×èÍÃÑ¡ÉÒ¤ÇÒÁÊͧÊÇÒ§·Õè´ÕáÅÐÂ×´ÍÒÂؤسÀÒ¾¾×é¹¼ÔÇ ãª¹éíÒÂÒ·íÒ¤ÇÒÁÊÐÍÒ´·ÕèäÁÁÕáÍÅ¡ÍÎÍÅËÃ×͵ÑÇ·íÒÅÐÅÒ¡Ѻ¼ÅÔµÀѳ±à·Ò¹Ñé¹ LED To replace the LED module or the entrire luminaire.Please consult your sales representative. ËÒ¡µÍ§¡ÒÃà»ÅÕè¹ LED module ËÃ×Íâ¤Áä¿â»Ã´µÔ´µÍµÑÇá·¹¢Ò¢ͧ¤Ø³ LED 230 V Environmental protection: Waste electrical products should not be disposed of with household waste. please recycle where facilities exist.check with your local authority or retailer for recycling advice According to directive 2002/96/CE and directive 2012/19/EU Waste Electrical and Electronic Equipment (WEEE). ËÒÁ·Ô駼ÅÔµÀѳ±¹éÃÕ ÇÁ¡Ñº¢ÂÐ㹤ÃÑÇàÃ×͹ª¹Ô´Í×è¹æàÁ×èÍÊÔé¹ÊØ´ÍÒÂØ¡ÒÃ㪧ҹâ»Ã´á¡¼ÅÔµÀѳ±ÍÍ¡ ¨Ò¡¢Í§àÊÕ»ÃÐàÀ·Í×è¹æáÅÐÃÕä«à¤ÔÅÍÂÒ§àËÁÒÐÊÁà¾×èÍʧàÊÃÔÁ¡ÒùíÒ·ÃѾÂҡáÅѺÁÒ㪫éíÒ«Ö觨ЪÇ »Í§¡Ñ¹ÍѹµÃÒµÍÊÔè§áÇ´ÅÍÁËÃ×ÍÊØ¢ÀÒ¾¢Í§Á¹ØÉ·Õèà¡Ô´¨Ò¡¡Ò÷Ô駢ÂÐâ´ÂäÁÁ¡Õ ÒäǺ¤ØÁ ÍÒ§ÍÔ§µÒÁÃÐàºÕº 2002/96/CE áÅÐÃÐàºÕº 2012/19/EU Waste Electrical and Electronic Equipment (WEEE). Last Revised On : 20/05/2024 REV.05 5/6 FR-DD-29 REV.00 EFF 11/03/24 Replacing the LED module ÇÔ¸Õ¡ÒÃà»ÅÕè¹ LED module 1. Contact your sales representative for replacement LED modules. Make sure that the replacement module match the initially supplied module. Note the part number printed on the LED module. àµÃÕÂÁ LED module ã˵ç¡ÑºÃع·ÕèµÍ§¡ÒÃà»ÅÕè¹â´ÂµÃǨÊͺ·ÕèËÁÒÂàÅ¢·Õè¾ÔÁ¾º¹LED modules áÅÐ µÔ´µÍµÑÇá·¹¢ÒÂà¾×èÍÊÑ觫×éÍ LED modules ·ÕèµÍ§¡ÒÃà»ÅÕè¹ 2. The LED module can be replaced by qualified persons using standard tools. ¡ÒÃà»ÅÕè¹ LED module µÍ§·íÒâ´ÂªÒ§¼ÙªíÒ¹Ò­áÅÐãªà¤Ã×èͧÁ×Í·Õèä´ÁÒµÃฐÒ¹ 3. Disconnect power before opening the luminaire housing. µÑ´áËŧ¨ÒÂ信͹·Õè¨Ðà»´µÑÇâ¤Á 4. Replace the old LED module with the new LED module. Reapply thermal interface material as supplied with the new LED module. ¶Í´ LED module ·ÕèªíÒÃØ´ÍÍ¡ ¨Ò¡¹Ñ¹·íÒ¤ÇÒÁÊÐÍÒ´¨Ø´ÇÒ§ËÅÍ´ áÅǨ֧·íÒ¡ÒûÃСͺ LED module ãËÁ áÅеͧà»ÅÕè¹ á¼¹Thermal Pad ËÃ×Í Thermal Grease ´Ç·ء¤ÃÑé§ 5. Inspect gaskets and if required replace with new gaskets. Defective luminaire covers must be replaced. Inspect correct wiring of replaced LED module. µÃǨÊͺ»ÃÐà¡ç¹áÅЪÔé¹Êǹ¢Í§µÑÇâ¤Á ¶ÒªíÒÃØ´àÊÕÂËÒÂãË·íÒ¡ÒÃà»ÅÕè¹ãËÁ áÅеÃǨÊͺ¡ÒÃà¢ÒÊÒÂ俢ͧ LED module ·Õèà»ÅÕè¹ãËÁ¶Ù¡µÍ§ËÃ×ÍäÁ 6. Close the luminaire housing before reconnecting power. »´½Ò¤ÃͺÅçͤâ¤Áä¿ãËàÃÕºÃÍÂ¡Í¹à»´ä¿ Last Revised On : 20/05/2024 REV.05 6/6 FR-DD-29 REV.00 EFF 11/03/24 ">
Публичная ссылка обновлена
Публичная ссылка на ваш чат обновлена.
