Unilamp Mini MIRA Round - Down Mode d'emploi

INSTALLATION MANUAL
PRODUCT NAME : Mini MIRA Round - Wall Downlight
Mini MIRA Round - Wall Up/Downlight
1.
220-240V~50-60Hz
Ordering Code
5060/5061-A-3-503-XX
2.
5060/5061-F-3-503-XX
3.
5060/5061-A-3-901-XX
4.
5060/5061-F-3-901-XX
5.
5060/5061-A-3-904-XX
6.
5060/5061-F-3-904-XX
+
Input voltage
-
No.
IP66
1-6
Light Emitting Diodes
LED
1
2
91
156
72
2.1
2.2
2.3
28
D
17.5
3.1
D
L
Screw size
¢¹Ò´Ê¡ÃÙ à¡ÅÕ ÂǻŋÍÂ
D
H
Wall plug anchor size
¢¹Ò´¾Å؍ ¡½˜§¼¹Ñ §
Ø7mm./ÁÁ.
3
D
L
Ø 7 mm./ÁÁ. 37 mm./ÁÁ.
L
H
Ø 4 mm. Ø 9 mm.
L
38 mm.
3.3
43.5
Bush protected against
dripping water.
ºÙª»‡Í§¡Ñ¹¹éíÒ«ÖÁࢌҵÑÇâ¤Á
105
3.2
6
17.5
Wall bracket
ệ¹ÂÖ´¼¹Ñ§
Last Revised On : 11/10/2022 REV.03
6
25
30
Cable size : 3x1.00 mm.2 8-13 mm.
¢¹Ò´ÊÒÂä¿
1/4
FR-DM-17 REV.03 EFF 15/09/17
4
5
4.2
N
4.1
4.3
L
4.4
Torque/áçºÔ´ : 3 Nm.
Installation complete
µÔ´µÑé§àÊÃç¨ÊÁºÙó
Remark :
ËÁÒÂà˵Ø
Warning :
¢ŒÍ¤ÇÃÃÐÇѧ
1. The manufacturer will not be liable or held responsible
for any incorrect installation, misuse or improper use
and unauthorised modification to the fittings. Failure
to comply with mentioned warning may cause serious
damage or serious injury to persons, animals or
objects. If any modification is required please consult
your dealer for the details.
·Ò§¼ÙŒ¼ÅÔµäÁ‹ÊÒÁÒöÃѺ¼Ô´ªÍºã¹¤ÇÒÁàÊÕÂËÒÂã´æ·Õèà¡Ô´¨Ò¡¡ÒÃ
µÔ´µÑé§äÁ‹¶Ù¡ÇÔ¸Õ, 㪌§Ò¹¼Ô´»ÃÐàÀ·ËÃ×Í´Ñ´á»Å§µÑÇâ¤Áã¹·Ø¡¡Ã³Õ
«Öè§ ÊÔ觼Դ»¡µÔàËŋҹÕé ÍÒ¨·íÒãË Œà¡Ô´ÍѹµÃÒ¡Ѻ ¤¹ ÊѵǏ ÊÔ觢ͧ
ËÒ¡ÁÕ¢ŒÍʧÊÑÂËÃ×ÍÁÕ¤ÇÒÁµŒÍ§¡Òûà Ѻᵋ§µÑÇâ¤Á
ãˌàËÁÒÐÊÁ¡Ñº¡ÒÃ㪌§Ò¹ ¡Ãس ÒµÔ´µ‹ÍµÑÇá·¹¨íÒ˹‹ÒÂËÃ×ͼٌ¼ÅÔµ
1. Installation should be carried out by a qualified
electrician in accordance with appropriate national
wiring regulation.
¡ÒõԴµÑé§â¤Áä¿¿‡ÒáÅÐÍØ»¡Ã³ ¤ÇôíÒà¹Ô¹¡ÒÃâ´Âª‹Ò§ä¿¿‡Ò
·ÕèÁÕ¤ÇÒÁÃٌáÅФÇÒÁªíÒ¹Ò­ 㹡ÒõԴµÑé§ÍØ»¡Ã³ä¿¿‡Ò
â´Â੾ÒеÒÁÁÒµÃฐÒ¹¢Í§¡ÒÃä¿¿‡Ò
2. Disconnect the power before changing the lamp.
»´ÊÇÔ·ªä¿·Ø¡¤ÃÑ駷Õèà»ÅÕè¹ËÅÍ´ä¿
3. This is Class1 luminaire, the installation must be
completed with earthing.
â¤Áä¿Ã؋¹¹Õé¶Ù¡¨Ñ´änj㹻ÃÐàÀ·¢Í§¡Òû‡Í§¡Ñ¹ä¿¿‡ÒÃÑèÇ ÃдѺ 1
·Õè¨ÐµŒÍ§µ‹ÍÊÒ´ԹµÒÁÁÒµÃฐÒ¹¤ÇÒÁ»ÅÍ´ÀÑÂ
4. Do not exceed the maximum wattage.
ˌÒÁ㪌ËÅÍ´ä¿·ÕèÁÕ¢¹Ò´Çѵµà¡Ô¹¡Ç‹Ò·ÕèÃÐºØ ËÃ×Í㪌ËÅÍ´¼Ô´»ÃÐàÀ·
2. Where damage has occured to the fittings, please
make the replacement with standard parts before use.
㹡óշÕèÁÕªÔé¹Ê‹Ç¹»ÃСͺã´à¡Ô´¤ÇÒÁàÊÕÂËÒ¡Ãس Òà»ÅÕè¹
ªÔé¹Ê‹Ç¹ãËÁ‹¡‹Í¹¡ÒÃ㪌§Ò¹·Ø¡¤Ãѧé à¾×èͤÇÒÁ»ÅÍ´ÀÑÂ
5. Don't touch LED while maintaining or cleaning.
ˌÒÁÊÑÁ¼ÑÊËÅÍ´ LED ¢³ÐºíÒÃاÃÑ¡ÉÒ ËÃ×Í·íÒ¤ÇÒÁÊÐÍÒ´
2
Cable Size/¢¹Ò´ÊÒÂä¿ : 3x1.00 mm. Ø8-13 mm.
In case the supply cable is exposed to sunlight use UV resistant cable.
¡Ã³Õ·ÕèÁÕ¡ÒõԴµÑé§â¤Á俹͡ÍÒ¤Òà ËÃ×Íâ¤Áä¿·ÕèÁÕ¡ÒÃἋÃѧÊÕÂÙÇÕ ÊÒÂ俵ŒÍ§ÊÒÁÒö»‡Í§¡Ñ¹ ËÃ×Í ÁÕ¡Òû‡Í§¡Ñ¹äÁ‹ãˌ¶Ù¡ÃѧÊÕÂÙÇÕ䴌
Last Revised On : 11/10/2022 REV.03
2/4
FR-DM-17 REV.03 EFF 15/09/17
Do not touch the LED because it may shorten the life time or the LED can be
breaking down.
ˌÒÁÊÑÁ¼ÑÊËÅÍ´ LED â´Âà´ç´¢Ò´ à¾ÃÒШзíÒãˌËÅÍ´àÊ×èÍÁÊÀÒ¾
NO
Minimum distance to lighted surface.
ÃÐÂÐˋҧ¢Ñé¹µèíÒ ¨Ò¡Ë¹ŒÒâ¤Á¶Ö§¾×é¹¼ÔÇ·Õè¶Ù¡Ê‹Í§ÊNjҧ
0.5 m
Any damaged safety glass cover must be replaced only with the original
spare part.
àÁ×èÍ¡ÃШ¡à¡Ô´¤ÇÒÁàÊÕÂËÒ à¾×èͤÇÒÁ»ÅÍ´ÀѤÇÃÊÑè§ÍÐäËŋ᷌¨Ò¡¼ÙŒ¼ÅԵ෋ҹÑé¹
NO
Not using chemical compounds and aggressive agents such as , weed
repellents fertilizers , acid solvent and contaminated irrigation water near the
Luminaires.
ˌÒÁ㪌ÊÒÃà¤ÁÕઋ¹ »Ø‰Â, ÂÒ¡íҨѴÈѵÃپת, »Ù¹¢ÒÇ, ÊÒÃÅÐÅÒ·Õè໚¹¡Ã´ áÅйéíÒ»¹à»„œÍ¹ÊÒÃà¤ÁÕ
ºÃÔàdz·ÕèµÔ´µÑé§â¤Áä¿
Make sure the plug is secured tightly and note the ground level.
¾Å؍¡µŒÍ§ÂÖ´Í‹ҧṋ¹Ë¹ÒáÅÐàÊÁ͡Ѻ¼ÔǾ×é¹
To reduce the risk of being constricted The wires attached to this lamp must be
effectively fixed to the wall. if the power cord is within reach.
à¾×èÍÅ´¤ÇÒÁàÊÕ觵‹Í¡Òö١ÊÒÂä¿à¡ÕèÂÇ/ÃÑ´ ÊÒÂä¿·Õ赋ÍࢌҵÑÇâ¤ÁµŒÍ§¶Ù¡µÔ´ÂÖ´¡Ñº¼¹Ñ§Í‹ҧàÃÕºÌÍÂ
Cable
Cable
LED
Last Revised On : 11/10/2022 REV.03
Our products are installed with electronic components with the protection against
overvoltage according to IEC 61547. The customers have to install the additional
overvoltage protection devices (against surge, transients, etc) in their electrical
system to avoid the risk of damage. Failing to do so can cause the end
of products warranty.
¼ÅÔµÀѳ±¢Í§àÃÒ䴌ÃѺ¡ÒõԴµÑé§Ãкº»‡Í§¡Ñ¹áç´Ñ¹ä¿¿‡Òà¡Ô¹µÒÁÁÒµÃฐÒ¹ IEC 61547
ÅÙ¡¤ŒÒµŒÍ§µÔ´µÑé§ÍØ»¡Ã³»‡Í§¡Ñ¹áç´Ñ¹ä¿¿‡Òà¡Ô¹à¾ÔèÁàµÔÁ(ઋ¹ »‡Í§¡Ñ¹ä¿¡ÃЪҡ ÏÅÏ )
ã¹Ãкºä¿¿‡Òà¾×èÍËÅÕ¡àÅÕ觤ÇÒÁàÊÕÂËÒ·ÕèÍÒ¨¨Ðà¡Ô´¢Öé¹ ËÒ¡ÅÙ¡¤ŒÒäÁ‹·íÒ¡ÒõԴµÑé§à¾ÔèÁ
àµÔÁÍÒ¨·íÒãˌ¡ÒÃÃѺ»ÃСѹÊÔ¹¤ŒÒÊÔé¹Êشŧ
3/4
FR-DM-17 REV.03 EFF 15/09/17
Clean the products regularly to maintain good light output and prolong surface
quality .
Only use solvent-free cleaning solutions on the products.
·íÒ¤ÇÒÁÊÐÍÒ´¼ÅÔµÀѳ ±à»š¹»ÃШíÒà¾×èÍÃÑ¡ÉÒ¤ÇÒÁʋͧÊNjҧ·Õè´ÕáÅÐÂ×´ÍÒÂؤسÀÒ¾¾×é¹¼ÔÇ
㪌¹éíÒÂÒ·íÒ¤ÇÒÁÊÐÍÒ´·ÕèäÁ‹ÁÕáÍÅ¡ÍÎÍŏËÃ×͵ÑÇ·íÒÅÐÅÒ¡Ѻ¼ÅÔµÀѳ±à·‹Ò¹Ñé¹
Do not use a high pressure washer to clean the products.
ˌÒÁ㪌à¤Ã×èͧ©Õ´¹éíÒáç´Ñ¹Ê٧㹡Ò÷íÒ¤ÇÒÁÊÐÍÒ´¼ÅÔµÀѳ ±
LED
LED
To replace the LED module or the entrire luminaire.Please consult your
sales representative.
ËÒ¡µŒÍ§¡ÒÃà»ÅÕè¹ LED module ËÃ×Íâ¤Áä¿â»Ã´µÔ´µ‹ÍµÑÇá·¹¢Ò¢ͧ¤Ø³
LED
230 V
Environmental protection: Waste electrical products should not be disposed of
with household waste. please recycle where facilities exist.check with your local
authority or retailer for recycling advice According to directive 2002/96/CE and
directive 2012/19/EU Waste Electrical and Electronic Equipment (WEEE).
ˌÒÁ·Ô駼ÅÔµÀѳ±¹ÕéËÇÁ¡Ñº¢ÂÐ㹤ÃÑÇàÃ×͹ª¹Ô´Í×è¹æàÁ×èÍÊÔé¹ÊØ´ÍÒÂØ¡ÒÃ㪌§Ò¹â»Ã´á¡¼ÅÔµÀѳ ±ÍÍ¡
¨Ò¡¢Í§àÊÕ»ÃÐàÀ·Í×è¹æáÅÐÃÕä«à¤ÔÅÍ‹ҧàËÁÒÐÊÁà¾×èÍʋ§àÊÃÔÁ¡ÒùíÒ·ÃѾÂҡáÅѺÁÒ㪌«éíÒ«Ö觨Ъ‹ÇÂ
»‡Í§¡Ñ¹ÍѹµÃÒµ‹ÍÊÔè§áǴŌÍÁËÃ×ÍÊØ¢ÀÒ¾¢Í§Á¹Øɏ·Õèà¡Ô´¨Ò¡¡Ò÷Ô駢ÂÐâ´ÂäÁ‹ÁÕ¡ÒäǺ¤ØÁ
͌ҧÍÔ§µÒÁÃÐàºÕº 2002/96/CE áÅÐÃÐàºÕº 2012/19/EU Waste Electrical and
Electronic Equipment (WEEE).
Replacing the LED module
ÇÔ¸Õ¡ÒÃà»ÅÕè¹ LED module
1. Contact your sales representative for replacement LED modules. Make sure that the replacement module
match the initially supplied module. Note the part number printed on the LED module.
àµÃÕÂÁ LED module ãˌµÃ§¡ÑºÃ؋¹·Õ赌ͧ¡ÒÃà»ÅÕè¹â´ÂµÃǨÊͺ·ÕèËÁÒÂàÅ¢·Õè¾ÔÁ¾º¹LED modules áÅÐ µÔ´µ‹ÍµÑÇá·¹¢ÒÂà¾×èÍÊÑ觫×éÍ
LED modules ·Õ赌ͧ¡ÒÃà»ÅÕè¹
2. The LED module can be replaced by qualified persons using standard tools.
¡ÒÃà»ÅÕè¹ LED module µŒÍ§·íÒâ´Âª‹Ò§¼ÙŒªíÒ¹Ò­áÅÐ㪌à¤Ã×èͧÁ×Í·Õè䴌ÁÒµÃฐÒ¹
3. Disconnect power before opening the luminaire housing.
µÑ´áËŋ§¨‹ÒÂä¿¡‹Í¹·Õè¨Ðແ´µÑÇâ¤Á
4. Replace the old LED module with the new LED module. Reapply thermal interface material as supplied with the
new LED module.
¶Í´ LED module ·ÕèªíÒÃØ´ÍÍ¡ ¨Ò¡¹ÑŒ¹·íÒ¤ÇÒÁÊÐÍÒ´¨Ø´ÇÒ§ËÅÍ´ áŌǨ֧ ·íÒ¡ÒûÃСͺ LED module ãËÁ‹ áÅеŒÍ§à»ÅÕè¹
Ἃ¹Thermal Pad ËÃ×Í Thermal Grease ´ŒÇ·ء¤ÃÑé§
5. Inspect gaskets and if required replace with new gaskets. Defective luminaire covers must be replaced. Inspect
correct wiring of replaced LED module.
µÃǨÊͺ»ÃÐà¡ç¹áÅЪÔé¹Ê‹Ç¹¢Í§µÑÇâ¤Á ¶ŒÒªíÒÃØ´àÊÕÂËÒÂãˌ·íÒ¡ÒÃà»ÅÕè¹ãËÁ‹ áÅеÃǨÊͺ¡ÒÃࢌÒÊÒÂ俢ͧ LED module
·Õèà»ÅÕè¹ãËÁ‹¶Ù¡µŒÍ§ËÃ×ÍäÁ‹
6. Close the luminaire housing before reconnecting power.
»´½Ò¤ÃͺÅçͤâ¤Áä¿ãˌàÃÕºÌÍ¡‹Í¹à»´ä¿
Last Revised On : 11/10/2022 REV.03
4/4
FR-DM-17 REV.03 EFF 15/09/17
">