INSTALLATION MANUAL
PRODUCT NAME : Mini AGAR Prismatic - Bollard
Mini AGAR Opal - Bollard
No.
1.
Input voltage
220-240V~ 50/60Hz
IP65
Ordering Code
7154/7155-0-3-855-XX
2.
7154/7155-0-3-856-XX
3.
7154/7155-0-3-869-XX
4.
7154/7155-0-3-870-XX
1-4
Light Emitting Diodes
(LED)
1
800
û173
û105
Mini AGAR Prismatic-Bollard / Mini AGAR Opal - Bollard
2
200
M8x1.25
1.1
Ø40
70
1.2
Ø105
Anchor bolt kit available separately
ªØ´ÊÁͽ§¾×é¹ áÍÅâºÅ· ᡨíÒ˹ÒÂ
Ordering Code/ÃËÑÊÊÑ駫×éÍ : 0269-0-9-000-00
Last Revised On 21/08/2023 REV.03
1/4
FR-DM-17 REV.03 EFF 15/09/17
3
4
Cable length 200 mm.
ÊÒÂä¿ÂÒÇ 200 ÁÁ.
3.2
3.1
25
4.2
Concrete.
¤Í¹¡ÃÕµ
3.3
4.1
3.4
Torque/áçºÔ´ : 11 Nm.
6
5
6.1
6
6.2
25
Torque/áçºÔ´ : 3 Nm.
6
30
2
Cable size : 3x1.00 mm. Ø7-12mm.
¢¹Ò´ÊÒÂä¿
5.1
L = BROWN (ÊÕ¹éí Ò µÒÅ)
Cable size :
¢¹Ò´ÊÒÂä¿
5
7
Use the rubber seal according to the size of the cable
àÅ× Í¡ãªÅÙ¡ÂÒ§à¤àºÔ Åá¡Åç ¹´ µÒÁ¢¹Ò´¢Í§ÊÒÂä¿
=Green and yellow (ÊÕ à¢Õ ÂÇ¡Ñ ºÊÕ àËÅ× Í§)
N = Blue (ÊÕ ¿Ò )
Make sure that the rubber seal is
correctly in place.
ÃÐÇÑ § ÅÙ ¡ÂÒ§ËÅØ ´ÍÍ¡¨Ò¡ªØ ´à¤àºÔé Åá¡Ã¹
Rubber seal size
ÅÙ¡ ÂÒ§à¤àºÔ Å á¡Åç ¹´·Õè ãª
9
Cable size Dia Ø 7-9 mm.
¢¹Ò´ÊÒÂä¿
Cable size Dia Ø 10-11 mm.
¢¹Ò´ÊÒÂä¿
12
7
1
2
6
4
8
9
3
IP68 Water Tight Connecting Device Cable Diameter 7 - 12mm.
Available Separately/ µÑǵÍÊÒ»ͧ¡Ñ¹¹éíÒµÑÇàÅç¡ ¨íÒ˹ÒÂᡵҧËÒ¡
Ordering Code/ÃËÑÊÊÑ觫×éÍ: 0248-0-9-000-00
Last Revised On 21/08/2023 REV.03
10
Make sure that cable
glands are fastened.
µÍ §¢Ñ ¹ Ê¡ÃÙã Ë á¹ ¹ ·Ø¡ µÑ Ç
Installation complete
µÔ´µÑé§àÊÃç¨ÊÁºÙó
2/4
FR-DM-17 REV.03 EFF 15/09/17
Remark :
ËÁÒÂà˵Ø
Warning :
¢Í¤ÇÃÃÐÇѧ
1. Installation should be carried out by a qualified electrician in
accordance with appropriate national wiring regulation.
¡ÒõԴµÑé§â¤Áä¿¿ÒáÅÐÍØ»¡Ã³ ¤ÇôíÒà¹Ô¹¡ÒÃâ´ÂªÒ§ä¿¿Ò
·ÕèÁÕ¤ÇÒÁÃÙáÅФÇÒÁªíÒ¹Ò­ 㹡ÒõԴµÑé§ÍØ»¡Ã³ä¿¿Ò
â´Â੾ÒеÒÁÁÒµÃฐÒ¹¢Í§¡ÒÃä¿¿Ò
1. The manufacturer will not be liable or held responsible for
any incorrect installation, misuse or improper use and
unauthorised modification to the fittings. Failure to comply
with mentioned warning may cause serious damage or
serious injury to persons, animals or objects. If any
modification is required please consult your dealer for the
details.
·Ò§¼Ù¼ÅÔµäÁÊÒÁÒöÃѺ¼Ô´ªÍºã¹¤ÇÒÁàÊÕÂËÒÂã´æ·Õèà¡Ô´¨Ò¡¡ÒõԴµÑé§
äÁ¶Ù¡ÇÔ¸Õ, 㪧ҹ¼Ô´»ÃÐàÀ·ËÃ×Í´Ñ´á»Å§µÑÇâ¤Áã¹·Ø¡¡Ã³Õ «Öè §
ÊÔ觼Դ»¡µÔàËÅÒ¹Õé ÍÒ¨·íÒãËà¡Ô´ÍѹµÃÒ¡Ѻ ¤¹ ÊÑµÇ ÊÔ觢ͧ
ËÒ¡ÁÕ¢ÍʧÊÑÂËÃ×ÍÁÕ¤ÇÒÁµÍ§¡ÒûÃѺᵧµÑÇâ¤Á ãËàËÁÒÐÊÁ¡Ñº¡ÒÃ㪧ҹ
¡ÃسҵԴµÍµÑÇá·¹¨íÒ˹ÒÂËÃ×ͼټÅÔµ
2. Disconnect the power before changing the lamp.
»´ÊÇÔ·ªä¿·Ø¡¤ÃÑ駷Õèà»ÅÕè¹ËÅÍ´ä¿
3. This is Class1 luminaire, the installation must be completed
with earthing.
â¤Áä¿Ãع¹Õé¶Ù¡¨Ñ´äÇã¹»ÃÐàÀ·¢Í§¡Òûͧ¡Ñ¹ä¿¿ÒÃÑèÇ ÃдѺ 1
·Õè¨ÐµÍ§µÍÊÒ´ԹµÒÁÁÒµÃฐÒ¹¤ÇÒÁ»ÅÍ´ÀÑÂ
2. Where damage has occured to the fittings, please make the
replacement with standard parts before use.
㹡óշÕèÁÕªÔé¹Êǹ»ÃСͺã´à¡Ô´¤ÇÒÁàÊÕÂËÒ¡ÃسÒà»ÅÕ蹪Ôé¹ÊǹãËÁ
¡Í¹¡ÒÃ㪧ҹ·Ø¡¤ÃÑé§ à¾×èͤÇÒÁ»ÅÍ´ÀÑÂ
4. Do not exceed the maximum wattage.
ËÒÁãªËÅÍ´ä¿·ÕèÁÕ¢¹Ò´Çѵµà¡Ô¹¡ÇÒ·ÕèÃÐºØ ËÃ×ÍãªËÅÍ´¼Ô´»ÃÐàÀ·
5. Don't touch LED while maintaining or cleaning.
ËÒÁÊÑÁ¼ÑÊËÅÍ´ LED ¢³ÐºíÒÃاÃÑ¡ÉÒ ËÃ×Í·íÒ¤ÇÒÁÊÐÍÒ´
Cable Size/¢¹Ò´ÊÒÂä¿ : 3x1.00 mm.2 Ø7-12 mm.
In case the supply cable is exposed to sunlight use UV resistant cable.
¡Ã³Õ·ÕèÁÕ¡ÒõԴµÑé§â¤Á俹͡ÍÒ¤Òà ËÃ×Íâ¤Áä¿·ÕèÁÕ¡ÒÃá¼ÃѧÊÕÂÙÇÕ ÊÒÂ俵ͧÊÒÁÒö»Í§¡Ñ¹ ËÃ×Í ÁÕ¡Òûͧ¡Ñ¹äÁã˶١ÃѧÊÕÂÙÇÕä´
Do not touch the LED because it may shorten the life time or the LED can be
breaking down.
ËÒÁÊÑÁ¼ÑÊËÅÍ´ LED â´Âà´ç´¢Ò´ à¾ÃÒШзíÒãËËÅÍ´àÊ×èÍÁÊÀÒ¾
NO
Any damaged safety glass cover must be replaced only with the original
spare part.
àÁ×èÍ¡ÃШ¡à¡Ô´¤ÇÒÁàÊÕÂËÒ à¾×èͤÇÒÁ»ÅÍ´ÀѤÇÃÊÑè§ÍÐäËÅá·¨Ò¡¼Ù¼ÅÔµà·Ò¹Ñé¹
NO
LED
Last Revised On 21/08/2023 REV.03
Not using chemical compounds and aggressive agents such as , weed repellents
fertilizers , acid solvent and contaminated irrigation water near the Luminaires.
ËÒÁãªÊÒÃà¤ÁÕહ »ØÂ, ÂÒ¡íҨѴÈѵÃپת, »Ù¹¢ÒÇ, ÊÒÃÅÐÅÒ·Õè໹¡Ã´ áÅйéíÒ»¹à»Í¹ÊÒÃà¤ÁÕ
ºÃÔàdz·ÕèµÔ´µÑé§â¤Áä¿
Our products are installed with electronic components with the protection against
overvoltage according to IEC 61547. The customers have to install the additional
overvoltage protection devices (against surge, transients, etc) in their electrical
system to avoid the risk of damage. Failing to do so will end the product warranty.
¼ÅÔµÀѳ±¢Í§àÃÒÁÕ¡ÒõԴµÑé§ÍØ»¡Ã³ÍÔàÅç¡·Ã͹ԡÊÊíÒËÃѺ¡Òûͧ¡Ñ¹áç´Ñ¹ä¿à¡Ô¹µÒÁÁÒµÃฐÒ¹
IEC 61547 áÅÐÅÙ¡¤ÒµÍ§µÔ´µÑé§ÍØ»¡Ã³»Í§¡Ñ¹áç´Ñ¹ä¿à¡Ô¹à¾ÔèÁàµÔÁ (»Í§¡Ñ¹ä¿¡ÃЪҡ
,ä¿¿ÒÅѴǧ¨Ã ÏÅÏ)ã¹Ãкºä¿¿Ò´Ç à¾×èÍËÅÕ¡àÅÕ觤ÇÒÁàÊÕ觷Õè¨Ðà¡Ô´¤ÇÒÁàÊÕÂËÒÂ
ËÒ¡äÁ´íÒà¹Ô¹¡Òôѧ¡ÅÒÇ ¡ÒÃÃѺ»ÃСѹ¨ÐÊÔé¹Êشŧ
3/4
FR-DM-17 REV.03 EFF 15/09/17
NO
NO
LED
LED
Clean the products regularly to maintain good light output and prolong surface
quality .
Only use solvent-free cleaning solutions on the products.
·íÒ¤ÇÒÁÊÐÍÒ´¼ÅÔµÀѳ ±à»¹»ÃШíÒà¾×èÍÃÑ¡ÉÒ¤ÇÒÁÊͧÊÇÒ§·Õè´ÕáÅÐÂ×´ÍÒÂؤسÀÒ¾¾×é¹¼ÔÇ
㪹éíÒÂÒ·íÒ¤ÇÒÁÊÐÍÒ´·ÕèäÁÁÕáÍÅ¡ÍÎÍÅËÃ×͵ÑÇ·íÒÅÐÅÒ¡Ѻ¼ÅÔµÀѳ±à·Ò¹Ñé¹
Do not use a high pressure washer to clean the products.
ËÒÁãªà¤Ã×èͧ©Õ´¹éíÒáç´Ñ¹Ê٧㹡Ò÷íÒ¤ÇÒÁÊÐÍÒ´¼ÅÔµÀѳ ±
To replace the LED module or the entrire luminaire.Please consult your
sales representative.
ËÒ¡µÍ§¡ÒÃà»ÅÕè¹ LED module ËÃ×Íâ¤Áä¿â»Ã´µÔ´µÍµÑÇá·¹¢Ò¢ͧ¤Ø³
LED
23 0 V
Environmental protection: Waste electrical products should not be disposed of
with household waste. please recycle where facilities exist.check with your local
authority or retailer for recycling advice According to directive 2002/96/CE and
directive 2012/19/EU Waste Electrical and Electronic Equipment (WEEE).
ËÒÁ·Ô駼ÅÔµÀѳ±¹ÕéÃÇÁ¡Ñº¢ÂÐ㹤ÃÑÇàÃ×͹ª¹Ô´Í×è¹æàÁ×èÍÊÔé¹ÊØ´ÍÒÂØ¡ÒÃ㪧ҹâ»Ã´á¡¼ÅÔµÀѳ ±ÍÍ¡
¨Ò¡¢Í§àÊÕ»ÃÐàÀ·Í×è¹æáÅÐÃÕä«à¤ÔÅÍÂÒ§àËÁÒÐÊÁà¾×èÍʧàÊÃÔÁ¡ÒùíÒ·ÃѾÂҡáÅѺÁÒ㪫éíÒ«Ö觨ЪÇÂ
»Í§¡Ñ¹ÍѹµÃÒµÍÊÔè§áÇ´ÅÍÁËÃ×ÍÊØ¢ÀÒ¾¢Í§Á¹ØÉ·Õèà¡Ô´¨Ò¡¡Ò÷Ô駢ÂÐâ´ÂäÁÁÕ¡ÒäǺ¤ØÁ
ÍÒ§ÍÔ§µÒÁÃÐàºÕº 2002/96/CE áÅÐÃÐàºÕº 2012/19/EU Waste Electrical and
Electronic Equipment (WEEE).
Replacing the LED module
ÇÔ¸Õ¡ÒÃà»ÅÕè¹ LED module
1. Contact your sales representative for replacement LED modules. Make sure that the replacement module
match the initially supplied module. Note the part number printed on the LED module.
àµÃÕÂÁ LED module ã˵ç¡ÑºÃع·ÕèµÍ§¡ÒÃà»ÅÕè¹â´ÂµÃǨÊͺ·ÕèËÁÒÂàÅ¢·Õè¾ÔÁ¾º¹LED modules áÅÐ µÔ´µÍµÑÇá·¹¢ÒÂà¾×èÍÊÑ觫×éÍ
LED modules ·ÕèµÍ§¡ÒÃà»ÅÕè¹
2. The LED module can be replaced by qualified persons using standard tools.
¡ÒÃà»ÅÕè¹ LED module µÍ§·íÒâ´ÂªÒ§¼ÙªíÒ¹Ò­áÅÐãªà¤Ã×èͧÁ×Í·Õèä´ÁÒµÃฐÒ¹
3. Disconnect power before opening the luminaire housing.
µÑ´áËŧ¨ÒÂ信͹·Õè¨Ðà»´µÑÇâ¤Á
4. Replace the old LED module with the new LED module. Reapply thermal interface material as supplied with the
new LED module.
¶Í´ LED module ·ÕèªíÒÃØ´ÍÍ¡ ¨Ò¡¹Ñ¹·íÒ¤ÇÒÁÊÐÍÒ´¨Ø´ÇÒ§ËÅÍ´ áÅǨ֧ ·íÒ¡ÒûÃСͺ LED module ãËÁ áÅеͧà»ÅÕè¹
á¼¹Thermal Pad ËÃ×Í Thermal Grease ´Ç·ء¤ÃÑé§
5. Inspect gaskets and if required replace with new gaskets. Defective luminaire covers must be replaced. Inspect
correct wiring of replaced LED module.
µÃǨÊͺ»ÃÐà¡ç¹áÅЪÔé¹Êǹ¢Í§µÑÇâ¤Á ¶ÒªíÒÃØ´àÊÕÂËÒÂãË·íÒ¡ÒÃà»ÅÕè¹ãËÁ áÅеÃǨÊͺ¡ÒÃà¢ÒÊÒÂ俢ͧ LED module
·Õèà»ÅÕè¹ãËÁ¶Ù¡µÍ§ËÃ×ÍäÁ
6. Close the luminaire housing before reconnecting power.
»´½Ò¤ÃͺÅçͤâ¤Áä¿ãËàÃÕºÃÍ¡͹໴ä¿
Last Revised On 21/08/2023 REV.03
4/4
FR-DM-17 REV.03 EFF 15/09/17
">
