Atlantic NAVILINK A59 Manuel utilisateur

PDF Download
Document
Atlantic Navilink A59: Manuel d'utilisation + IA | Fixfr

User questions

B P

Jennifer B.

Why is the heat pump in vacation mode while the thermostat is in OFF mode?
No votes
Vacation mode allows programming an absence and displays the remaining duration when active. To cancel it, press the dedicated button again. Without more information, the exact cause of this behavior is difficult to determine.
Q R

Patricia Q.

How to exit manual mode?
No votes
Wait 24 hours; the setting will automatically revert to the initial programming. Or, press the button to cancel the override.
Q R

Patricia Q.

Which button cancels manual mode?
No votes
The button (the one illustrated with a hand) cancels the manual mode.
Q R

Patricia Q.

How to cancel manual mode using the button?
No votes
The button (the one illustrated with a hand) cancels the manual mode.
L O

John L.

How does the 'hand' symbol in the advanced settings menu disappear?
No votes
The 'hand' symbol in the advanced menu automatically disappears when the setpoint override is cancelled, either after 24 hours or upon returning to the initial state. This indicates the completion of the manual setting and the system's return to normal operation.
L O

John L.

How to return to the initial state?
No votes
The cancellation of the override, which makes the 'hand' symbol disappear, occurs automatically after 24 hours or when you return to the initial state. This indicates that the manual setting is complete and the system returns to its normal operation.
T M

Mary T.

What happens if the Navilink A59 is set to OFF mode?
No votes
The viewed document does not provide specific information on what happens when you set the Navilink A59 to OFF mode. The behavior of the OFF mode can vary depending on your specific installation. It is recommended to consult your heating system documentation or contact your installer for precise details about how the OFF mode functions with your configuration.
T M

Mary T.

How to permanently change the setpoint value?
No votes
According to the viewed document, you can permanently change the setpoint value using the Simplified Menu: Direct Setpoint. Here are the general steps: 1. Press the appropriate button (the viewed document does not specify which button, but it should be identifiable by its symbol). 2. The setpoint will flash, indicating that you can change it. 3. Change the setpoint using the appropriate buttons (the viewed document does not specify which buttons, but they should be identifiable by their symbols). 4. Once the desired setpoint is chosen, wait 5 seconds. The flashing will stop, and the setpoint will be permanently changed. Note: The viewed document also describes an "Advanced Menu: Manual Mode" where the setpoint modification is temporary (24h). Ensure you are using the "Simplified Menu: Direct Setpoint" for a permanent change.
T M

Mary T.

How to find the Simplified Menu?
No votes
The viewed document does not explicitly detail how to access the "Simplified Menu". However, it describes two methods for setting the setpoint: one via an "Advanced Menu: Manual Mode" and another via a "Simplified Menu: Direct Setpoint". It's possible that the "Simplified Menu" is the default screen or a more direct mode of operation, accessible without going through the Installer Menu. Try pressing the button mentioned previously for setting the setpoint (without going through the Installer Menu) and see if it allows you to directly modify the setpoint. If the setpoint flashes and you can change it with the buttons, you are probably in the "Simplified Menu". Otherwise, you might be in the default "Advanced Menu", or there might be another access method not described in the viewed document. Without clear instructions in the viewed document, it is difficult to provide a precise answer. It is recommended to consult the complete user manual of your device or contact your installer for specific instructions on accessing the "Simplified Menu".
B P

Jennifer B.

How to return to the home screen from the 'ioAJ' screen?
No votes
To return to the home screen from the 'ioAJ' screen, select 'FIn' using the buttons and wait 5 seconds. Alternatively, if 'Sde' is flashing, successful pairing will cause the display to return to the home screen. If pairing fails, restart the procedure, or select 'FIn' to return to the home screen if you do not want to pair a second probe.
T M

Mary T.

What happens when the Navilink A59 is set to OFF mode?
No votes
The effect of setting the Navilink A59 to OFF mode can vary depending on the specific installation. Precise details on how the OFF mode behaves with your setup are dependent on your specific installation and setup.
Preparing document for printing…
0%