ENGLISH SUBWOOFER ESPAŃOL FRANÇAIS CAISSON DE GRAVE CS-AW8520 CS-AW8540 CS-AW8520 & CS-AW8540 For Customer Use: Enter below the Model No, and Serial No, which is located either on the rear or bottom of the speaker unit. Retain this information for future reference. Model No. INSTRUCTION MANUAL MANUEL D'INSTRUCTIONS MANUAL DE INSTRUCCIONES Serial No. LVT1861-001A ENGLISH Thank you for purchasing the ARSENAL Car Stereo Speaker. These Speakers can be mounted in the trunk of your vehicle. For the secure installation and perfect operation of your speakers, please read the following carefully. Parts 2. Screw x 10 3. Jump 4. Fuse (15A) x 2 5. Hexagon socket screw keys 1. Grille For proper installation and use 1.Before connecting the speakers to the amplifier, confirm that the power has been turned off. The click noise generated by the connection if the power is on may damage the speakers. 2.The amplifier and speakers should be connected between corresponding terminals, i.e. left to left, and right to right, as well as "+" to "+", and "–" to "–". Connection with reversed polarity will degrade the quality of stereo reproduction. 3.Do not subject the speakers to excessive input. The power handling capacity of the CS-AW8520/CS-AW8540 is 1500 watts (R.M.S. MUSIC POWER). Any excessive input may damage the speakers. 4.The CS-AW8520/CS-AW8540 has an impedance of 2Ω,4Ω,8Ω. Make sure that the output impedance of the amplifier's speaker terminal is rated at 2Ω,4Ω,8Ω. 5.When cleaning the speakers, use a soft cloth and wipe the surface gently. Do not apply thinner or solvent. 6.Be sure to carefully follow the instructions for: Cable Connections Fuse Replacement Switching the Impedance Selector Subwoofer Mounting and Smart Trim Ring Installation Consult Page 15 of this Instruction Manual for details on these procedures. -2- Dual 4 Ω Application Diagrams 1 Mono Amplifier 1 Subwoofer Jumper set to Series 8Ω(4Ω+4Ω) Load SERIES JUMPER 1 Mono Amplifier 1 Subwoofer Jumper set to Parallel 8Ω(4Ω+4Ω) Load PARALLEL SERIES Jumper Plug Bi-Amp Mono Input 4Ω Input - - Only + + PARALLEL Jumper Plug Input ENGLISH JUMPER Bi-Amp Mono 4Ω 8Ω Input - - Only + + 4Ω 4Ω 2Ω *JUMPER is Removed 1 2ch Amplifier 1 Subwoofer Jumper is Removed 4Ω Load SERIES Input Stereo + Bi-Amp Configuration 2 Mono Amplifiers 1 Subwoofer Jumper is Removed 4Ω Load *JUMPER is Removed PARALLEL Bi-Amp - Only + SERIES Mono Input - Input Bi-Amp Input - - Only + + 4Ω PARALLEL Mono 4Ω 2-Chan 4Ω JUMPER 1 Mono Amplifier 2 Subwoofers Jumper set to Series Subwoofers wired in Parallel 4Ω Load SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono Input - - Only + + 4Ω 8Ω PARALLEL Jumper Plug Input Bi-Amp 4Ω Input - - Only + + 4Ω 8Ω 4Ω 4Ω JUMPER 1 Mono Amplifier 3 Subwoofers Jumper set to Series Subwoofers wired in Parallel 2.6Ω Load SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 4Ω 8Ω PARALLEL SERIES Jumper Plug Input - - Only + + JUMPER Input Bi-Amp 4Ω Input - - Only + + 4Ω 8Ω PARALLEL Jumper Plug Input Bi-Amp 4Ω Input - - Only + + 4Ω 8Ω 4Ω 2.6Ω JUMPER 1 Mono Amplifier 4 Subwoofers Jumper set to Series Subwoofers wired in Parallel 2Ω Load SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 4Ω 8Ω - 4Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp 4Ω 8Ω 2Ω - -3- 4Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp Input - - Only + + 4Ω 8Ω 4Ω PARALLEL Jumper Plug Input Bi-Amp - Only + + 4Ω 8Ω Input - 4Ω Dual 2 Ω Application Diagrams 1 Mono Amplifier 1 Subwoofer Jumper set to Series 4Ω(2Ω+2Ω) Load SERIES JUMPER 1 Mono Amplifier 1 Subwoofer Jumper set to Parallel 4Ω(2Ω+2Ω) Load PARALLEL SERIES Jumper Plug Input Bi-Amp Mono Input 2Ω Input - - Only + + PARALLEL Jumper Plug ENGLISH JUMPER Bi-Amp Mono 2Ω 4Ω Input - - Only + + 2Ω 2Ω 1Ω *JUMPER is Removed 1 2ch Amplifier 1 Subwoofer Jumper is Removed 2Ω Load SERIES Input Stereo + Bi-Amp Configuration 2 Mono Amplifiers 1 Subwoofer Jumper is Removed 2Ω Load *JUMPER is Removed PARALLEL Bi-Amp - Only + SERIES Mono Input - Input Bi-Amp Input - - Only + + 2Ω PARALLEL Mono 2Ω 2-Chan 2Ω JUMPER 1 Mono Amplifier 2 Subwoofers Jumper set to Series Subwoofers wired in Parallel 2Ω Load SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono Input - - Only + + 2Ω 4Ω PARALLEL Jumper Plug Input Bi-Amp 2Ω Input - - Only + + 2Ω 4Ω 2Ω 2Ω JUMPER 1 Mono Amplifier 3 Subwoofers Jumper set to Series Subwoofers wired in Parallel 1.3Ω Load SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 2Ω 4Ω PARALLEL SERIES Jumper Plug Input - - Only + + JUMPER Input Bi-Amp 2Ω Input - - Only + + 2Ω 4Ω PARALLEL Jumper Plug Input Bi-Amp 2Ω Input - - Only + + 2Ω 4Ω 2Ω 1.3Ω JUMPER 1 Mono Amplifier 4 Subwoofers Jumper set to Series Subwoofers wired in Parallel 1Ω Load SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 2Ω 4Ω - 2Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp 2Ω 4Ω 1Ω - -4- 2Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp Input - - Only + + 2Ω 4Ω 2Ω PARALLEL Jumper Plug Input Bi-Amp - Only + + 2Ω 4Ω Input - 2Ω When the speaker cannot be attached in the car, make the sealed enclosure as recommended in the table below—20 mm (3/4 inch) MDF is also recommended for the enclosure materials. CS-AW8520 & 8540 A 26-14/32 inch (671.8 mm) B 16-28/32 inch (429 mm) C 10-31/32 inch (278.9 mm) D 13-26/32 inch (351.2 mm) E 13-18/32 inch (370mm) F 4/32 inch (3 mm) G 2.205 ft3 (0.062 m3) Front & Rear Baffle Boards (x 2) C Top & Bottom Sides (x 2) B G : Internal Volume A Left & Right Sides (x 2) Mounting Hole Dimension * Screw: Dia. 4mm x 50mm (x 8) (supplied) To install the ported enclosure When the speaker cannot be attached in the car, make the sealed enclosure as recommended in the table below—20 mm (3/4 inch) MDF is also recommended for the enclosure materials. CS-AW8520 & 8540 A 26-14/32 inch (671.8 mm) B 16-28/32 inch (429 mm) C 10-31/32 inch (278.9 mm) D 13-26/32 inch (351.2 mm) E 13-18/32 inch (370mm) F 4/32 inch (3 mm) G 3 inch (76.2 mm) H 9 inch (228.6 mm) I 21 inch (533.4 mm) Front & Rear Baffle Boards (x 2) J 3.255 ft3 (0.092 m3) C B Top & Bottom Sides (x 2) J : Internal Volume A Left & Right Sides (x 2) G I * Screw: Dia. 4mm x 50mm (x 8) (supplied) H -5- Mounting Hole Dimension ENGLISH To install the sealed enclosure ENGLISH Nominal Impedance (Ω) SPL (dB,1W/1M) Displacement (Liter) Hole Cutout Diameter (inch) (mm) Mounting Depth (inch) (mm) CS-AW8520 parallel series 2Ω + 2Ω 88.09 dB 88.23 dB 0.403 ft3 Dia. 13 - 30/32 inch ( 354 mm ) 9 - 22/32 inch ( 245.85 mm ) CS-AW8540 parallel series 4Ω + 4Ω 88.37 dB 88.44dB 0.403 ft3 Dia. 13 - 30/32 inch ( 354 mm ) 9 - 22/32 inch ( 245.85 mm ) Re (Ω) 1.03 Ω 3.99 Ω 2.08 Ω 8.20 Ω Re : DC voice coil resistance BL (T.M) 10.71 21.39 14.38 28.78 BL : Product of Flux density and Effective Voicecoil-wire length Vas (Liter) 88.99 L 89.16 L 95.157 L 95.445 L Vas : Volume of air equal to the driver compliance Vas (CuFt) Me (g) D (mm) 3.14 ft3 3.14 ft3 299.92 g 299.10 g Dia. 253 mm 3.36 ft3 3.37 ft3 274.15 g 274.04 g Me : Effective mass Dia. 253 mm D : Effective cone diameter Fs (Hz) 27.7 Hz 27.7 Hz 28.0 Hz 27.9 Hz Qms 6.396 6.413 5.517 5.472 Qes 0.466 0.453 0.483 0.476 Qts 0.434 0.423 0.445 0.438 Parameters Pe [max.] (W) 1500 W 1500 W Xmax.(mm) 24.7 mm 23.7 mm 28 ~500 Hz 308.94 oz ( 8757.96 g ) Dia. 3 - 7/32 inch ( 80.54 mm ) 51.6 mm 10 mm 29 ~500 Hz 308.94 oz ( 8757.96 g ) Dia. 3 - 7/32 inch ( 80.54 mm ) 51.6 mm 10 mm Freq.Responce (Hz) Magnet Mass (oz) (g) Voice Coil(Aluminum)Dia.(inch) (mm) Hvc (mm) Hag (mm) -6- NOTES SPL : Sound pressure level Fs : Driver free air resonance Qms : Q of driver at Fs considering only non-electrical resistance Qes : Q of driver at Fs considering only electrical resistance Qts : Total Q of driver at Fs Pe[max.] : Maximum continuous input power Xmax. : Maximum effective voicecoil travel without distortion Hvc : Voice coil Height Hag : Gap Height Nous vous remercions pour I'achat d'un haut-parleur auto stéréo de ARSENAL dans le coffre de votre véhicule. Pour un montage sûr et un fonctionnement parfait de ce haut-parleur, il est conseillé de lire attentivement ce qui suit. 2. Screw x 10 3. Jump 4. Fuse (15A) x 2 5. Hexagon socket screw keys 1. Grille Montage et utilisation corrects 1.Vérifier que l'alimentation est coupée avant de raccorder les haut-parleurs à l'amplificateur. Les craquements produits par le raccordement lors que l'alimentation est fournie peuvent endomma ger les haut-parleurs. 2.Raccorder les bornes correspondantes de l’amplificateur et les haut-parleurs, c'est-à-dire, gauche à gauche, droit à droite, de même que “+” à “+” et “–” à “–”. Un raccordement effectué en inversant les polarités réduira la qualité de la reproduction sonore stéréo-phonique. 3.Ne pas appliquer un niveau d'entrée excessif aux haut-parleurs. La puissance d'entrée admissible pour les haut-parleurs CS-AW8520/CS-AW8540 est de 1500 watts (puissance musicale R.M.S.). Tout signal d'entrée excessif risque de les endommager. 4.Les haut-parleurs CS-AW8520/CS-AW8540 ont une impédance de 2Ω,4Ω,8Ω. ll faut par conséquent s'assurer que l'impédance de sortie aux bornes de haut-parleur de l'amplificateur soit aussi de 2Ω,4Ω,8Ω. 5.Nettoyer le haut-parleur en le frottant légèrement à l'aide d'un chiffon doux. Ne jamais utiliser de solvants ni de détergents. 6.Veuillez suivre attentivement les instructions suivantes pour: Connections de Câble Remplacement de Fusible Changement de la Sélection d'Impédance Montage du Subwoofer et Installation Pratique de la Moulure de Finition Consultez la Page 15 de ce Manuel d'Instruction pour les détails de cesprocédures. -7- FRANÇAIS Parts Diagrammes d’application duale 4Ω JUMPER SERIES PARALLEL Jumper Plug Input Bi-Amp Mono 4Ω SERIES Input Input - - Only + + FRANÇAIS 1 amplificateur mono 1 (un) caisson de basse Cavalier branché en Parallèle Impédance de charge de 8Ω(4Ω+4Ω) Bi-Amp Mono 8Ω Input - - Only + + 4Ω PARALLEL Jumper Plug 1 amplificateur mono 1 (un) caisson de basse Cavalier branché en Série Impédance de charge de 8Ω(4Ω+4Ω) JUMPER 4Ω 4Ω 2Ω *JUMPER is Removed 1 amplificateur mono 1 (un) caisson de basse Cavalier branché en Parallèle Impédance de charge de 8Ω(4Ω+4Ω) SERIES Configuration en double amplification 2 amplificateurs mono *JUMPER is Removed 1 (un) caisson de basse Cavalier débranché Impédance de charge de 4Ω PARALLEL SERIES Input Stereo + Bi-Amp - Only + PARALLEL Input - Mono Input 4Ω 4Ω 2-Chan Bi-Amp Input - - Only + + Mono 4Ω JUMPER 1 amplificateur mono 2 (deux) caissons de basse Cavalier branché en Série Subwoofers wired in Parallel Impédance de charge de 4Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono Input - - Only + + 4Ω 8Ω PARALLEL Jumper Plug Input Bi-Amp 4Ω Input - - Only + + 4Ω 8Ω 4Ω 4Ω JUMPER 1 amplificateur mono 3 (trois) caissons de basse Cavalier branché en Série Subwoofers wired in Parallel Impédance de charge de 2.6Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 4Ω 8Ω PARALLEL SERIES Jumper Plug Input - - Only + + JUMPER Input Bi-Amp 4Ω Input - - Only + + 4Ω 8Ω PARALLEL Jumper Plug Input Bi-Amp 4Ω Input - - Only + + 4Ω 8Ω 4Ω 2.6Ω JUMPER 1 amplificateur mono 4 (quatre) caissons de basse Cavalier branché en Série Subwoofers wired in Parallel Impédance de charge de 2Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 4Ω 8Ω - 4Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp 4Ω 8Ω 2Ω - -8- 4Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp Input - - Only + + 4Ω 8Ω 4Ω PARALLEL Jumper Plug Input Bi-Amp - Only + + 4Ω 8Ω Input - 4Ω Diagrammes d’application duale 2Ω JUMPER PARALLEL Jumper Plug Input Bi-Amp Mono Input 2Ω Input - - Only + + SERIES Bi-Amp Mono 4Ω Input - - Only + + 2Ω PARALLEL 2Ω 2Ω 1Ω *JUMPER is Removed 1 amplificateur mono 1 (un) caisson de basse Cavalier branché en Parallèle Impédance de charge de 4Ω(2Ω+2Ω) SERIES Configuration en double amplification 2 amplificateurs mono *JUMPER is Removed 1 (un) caisson de basse Cavalier débranché Impédance de charge de 2Ω PARALLEL SERIES Input Stereo + Bi-Amp - Only + PARALLEL Input - Mono Input 2Ω 2Ω 2-Chan Bi-Amp Input - - Only + + Mono 2Ω JUMPER 1 amplificateur mono 2 (deux) caissons de basse Cavalier branché en Série Subwoofers wired in Parallel Impédance de charge de 2Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono Input - - Only + + 2Ω 4Ω PARALLEL Jumper Plug Input Bi-Amp 2Ω Input - - Only + + 2Ω 4Ω 2Ω 2Ω JUMPER 1 amplificateur mono 3 (trois) caissons de basse Cavalier branché en Série Subwoofers wired in Parallel Impédance de charge de 1.3Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 2Ω 4Ω PARALLEL SERIES Jumper Plug Input - - Only + + JUMPER Input Bi-Amp 2Ω Input - - Only + + 2Ω 4Ω PARALLEL Jumper Plug Input Bi-Amp 2Ω Input - - Only + + 2Ω 4Ω 2Ω 1.3Ω JUMPER 1 amplificateur mono 4 (quatre) caissons de basse Cavalier branché en Série Subwoofers wired in Parallel Impédance de charge de 1Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 2Ω 4Ω - 2Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp 2Ω 4Ω 1Ω - -9- 2Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp Input - - Only + + 2Ω 4Ω 2Ω PARALLEL Jumper Plug Input Bi-Amp - Only + + 2Ω 4Ω Input - 2Ω FRANÇAIS SERIES 1 amplificateur mono 1 (un) caisson de basse Cavalier branché en Parallèle Impédance de charge de 4Ω(2Ω+2Ω) Jumper Plug 1 amplificateur mono 1 (un) caisson de basse Cavalier branché en Série Impédance de charge de 4Ω(2Ω+2Ω) JUMPER Pour installer l’enceinte hermétique Si le haut-parleur ne peut pas être fixé directement dans cette voiture, fabriquez une enceinte hermétique de façon recommandéeà l’aide des spécifications données dans le tableau ci-dessous; le CS-AW8520 & 8540 MDF—20 mm (3/4 pouce) est recommandé pour le matériau de l’enceinte. A 26-14/32 inch (671.8 mm) B 16-28/32 inch (429 mm) C 10-31/32 inch (278.9 mm) D 13-26/32 inch (351.2 mm) E 13-18/32 inch (370mm) F 4/32 inch (3 mm) G 2.205 ft3 (0.062 m3) Écrans acoustiques avant et arrière (x 2) FRANÇAIS C B Faces supérieure et inférieure (x 2) G : Volume interne A Faces gauche et droite (x 2) Faces gauche et droite (x 2) * Vis: Dia. 4mm x 50mm (x 8) (fournis) Pour installer l’enceinte hermétique Si le haut-parleur ne peut pas être fixé directement dans cette voiture, fabriquez une enceinte hermétique de façon recommandéeà l’aide des spécifications données dans le tableau ci-dessous; le CS-AW8520 & 8540 MDF—20 mm (3/4 pouce) est recommandé pour le matériau A 26-14/32 inch (671.8 mm) de l’enceinte. B 16-28/32 inch (429 mm) C 10-31/32 inch (278.9 mm) D 13-26/32 inch (351.2 mm) E 13-18/32 inch (370mm) F 4/32 inch (3 mm) G 3 inch (76.2 mm) H 9 inch (228.6 mm) I 21 inch (533.4 mm) Écrans acoustiques avant et arrière (x 2) J 3.255 ft3 (0.092 m3) C B Faces supérieure et inférieure (x 2) J : Volume interne A G I * Vis: Dia. 4mm x 50mm (x 8) (fournis) H - 10 - Faces gauche et droite (x 2) Faces gauche et droite (x 2) CS-AW8540 parallel series 4Ω + 4Ω 88.37 dB 88.44dB 0.403 ft3 Dia. 13 - 30/32 inch ( 354 mm ) 9 - 22/32 inch ( 245.85 mm ) Re (Ω) 1.03 Ω 3.99 Ω 2.08 Ω 8.20 Ω BL (T.M) 10.71 21.39 14.38 28.78 Vas (Iitre) 88.99 L 89.16 L 95.157 L 95.445 L Vas (CuFt) Me (g) D (mm) 3.14 ft3 3.14 ft3 3.36 ft3 299.92 g 299.10 g Dia. 253 mm 3.37 ft3 274.15 g 274.04 g Dia. 253 mm Fs (Hz) 27.7 Hz 27.7 Hz 28.0 Hz 27.9 Hz Qms 6.396 6.413 5.517 5.472 Qes 0.466 0.453 0.483 0.476 Qts 0.434 0.423 0.445 0.438 Pe [max.] (W) 1500 W 1500 W Xmax. (mm) 24.7 mm 23.7 mm 28 ~500 Hz 308.94 oz ( 8757.96 g ) Dia. 3 - 7/32 inch ( 80.54 mm ) 51.6 mm 10 mm 29 ~500 Hz 308.94 oz ( 8757.96 g ) Dia. 3 - 7/32 inch ( 80.54 mm ) 51.6 mm 10 mm Réponse en fréquence (Hz) Masse de l’aimant (once) (g) Diamètre de la bobine mobile (pouces) (mm) Hvc (mm) Hag (mm) - 11- REMARQUES SPL : Niveau de pression sonore Re : Résistance de la bobine mobile en CC BL : Produit de la densité de flux et de la longueur efficace de fil de la bobine mobile Vas : Volume d'air égal à la conformité de l'excitateur Me : Masse effective D : Diamètre effectif du cône Fs : Résonance à l'air libre de l'excitateur Qms : Q de l'excitateur à Fs considérant uniquement la résistance non-électrique Qes : Q de l'excitateur à Fs considérant uniquement la résistance électrique Qts : Q total de l'excitateur à Fs Pe[max.] : Puissance d'entrée continue maximum Xmax. : Déplacement effectif maximum de la bobine mobile sans distorsion Hvc : Hauteur de la bobine mobile Hvc : Hauteur de la bobine mobile FRANÇAIS CS-AW8520 parallel series Impédance nominale (Ω) 2Ω + 2Ω SPL (dB,1W/1M) 88.09 dB 88.23 dB Déplacement (Liter) 0.403 ft3 Diamètre du tuou de découpe (pouces) Dia. 13 - 30/32 inch (mm) ( 354 mm ) Profondeur de montage (pouces) 9 - 22/32 inch (mm) ( 245.85 mm ) Paramètres Le agradecemos la adquisición del Altavoz Estereofónico para Automóvil de ARSENAL. Para efectuar una instalación segura y para que el altavoz funcione correctamente, lea detenidamente las siguientes instrucciones. ESPAŃOL Parts 2. Screw x 10 3. Jump 4. Fuse (15A) x 2 5. Hexagon socket screw keys 1. Grille Instalación y uso correctos 1.Antes de conectar los altavoces con el amplificador, confirme que esté cortada la alimentación eléctrica. El ruido producido al realizar la conexión con la alimentación conectada puede causar daños en los altavoces. 2.Deben conectares los terminales correspondientes del amplificador y de los altavoces, es decir izquierdo a izquierdo y derecho a derecho,asi co mo “+” a “+” y “–” a “–”. Si las polaridades se co nectan inversamente, la reproducción este reofónica se deteriorará. 3.No someta los altavoces a una entrada excesiva. La capacidad máxima de los CS-AW8520/CS-AW8540 es de 1500 votios (POTENCIA MUSICAL R.M.S.). Una entra da excesiva dañará los altavoces. 4.Los CS-AW8520/CS-AW8540 tienen 2Ω,4Ω,8Ω de impedancia. Asegúrese de que la impe dancia de salida del terminal para altavoces de amplificador sea de 2Ω, 4Ω ,8Ω. 5.Cuando limpie los altavoces, utilice un paño suave y frote la superficie con cuidado. No aplique solventes ni diluyentes. 6.Asegurese de seguir cuidadosamente las instrucciones para: Conecciones de Cable Reemplazo de fucible Cambiando el Selector de Resistencia Instalar el subwoofer y la moldura del anillo Consulte la Page 15 de este Manual de Instrucciones para los detalles de estos procedimientos. - 12- Diagramas de Aplicasion Dual 4Ω JUMPER SERIES 1 amplificador monofónico 1(un) bajo Puente fijado en Paralelo Carga a 8Ω(4Ω+4Ω) PARALLEL SERIES Jumper Plug Bi-Amp Mono Input 4Ω Input - - Only + + Jumper Plug Input PARALLEL Bi-Amp Mono 4Ω 8Ω Input - - Only + + 4Ω 4Ω 2Ω *JUMPER is Removed Amplificador 1,2 ch 1(un) bajo Se quita el puente Carga a 4Ω SERIES Input Stereo + Configuracion Bi-Amplificada 2 amplificadores monofónicos 1(un) bajo Se quita el puente Carga a 4Ω *JUMPER is Removed PARALLEL Bi-Amp - Only + SERIES Mono Input - Input Bi-Amp Input - - Only + + 4Ω PARALLEL Mono 4Ω 2-Chan 4Ω JUMPER 1 amplificador monofónico 2 (Dos) bajos Puente fijado en serie Subwoofers wired in Parallel Carga a 4Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono Input - - Only + + 4Ω 8Ω PARALLEL Jumper Plug Input Bi-Amp 4Ω Input - - Only + + 4Ω 8Ω 4Ω 4Ω JUMPER 1 amplificador monofónico 3 (Tres) bajos Puente fijado en serie Subwoofers wired in Parallel Carga a 2.6Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 4Ω 8Ω PARALLEL SERIES Jumper Plug Input - - Only + + JUMPER Input Bi-Amp 4Ω Input - - Only + + 4Ω 8Ω PARALLEL Jumper Plug Input Bi-Amp 4Ω Input - - Only + + 4Ω 8Ω 4Ω 2.6Ω JUMPER 1 amplificador monofónico 4 (Cuatro) bajos Puente fijado en serie Subwoofers wired in Parallel Carga a 2Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 4Ω 8Ω - 4Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp 4Ω 8Ω 2Ω - - 13 - 4Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp Input - - Only + + 4Ω 8Ω 4Ω PARALLEL Jumper Plug Input Bi-Amp - Only + + 4Ω 8Ω Input - 4Ω ESPAŃOL 1 amplificador monofónico 1(un) bajo Puente fijado en serie Carga a 8Ω(4Ω+4Ω) JUMPER Diagramas de Aplicasion Dual 2Ω JUMPER 1 amplificador monofónico 1(un) bajo Puente fijado en serie Carga a 4Ω(2Ω+2Ω) SERIES JUMPER 1 amplificador monofónico 1(un) bajo Puente fijado en Paralelo Carga a 4Ω(2Ω+2Ω) PARALLEL SERIES Jumper Plug Bi-Amp Mono Input 2Ω Input - - Only + + Jumper Plug Input Bi-Amp Mono 2Ω Input - - Only + + 4Ω 2Ω 2Ω 1Ω *JUMPER is Removed ESPAŃOL PARALLEL Amplificador 1,2 ch 1(un) bajo Se quita el puente Carga a 2Ω SERIES Input Stereo + Configuracion Bi-Amplificada 2 amplificadores monofónicos 1(un) bajo Se quita el puente Carga a 2Ω *JUMPER is Removed PARALLEL Bi-Amp - Only + SERIES Mono Input - Input Bi-Amp Input - - Only + + 2Ω PARALLEL Mono 2Ω 2-Chan 2Ω JUMPER 1 amplificador monofónico 2 (Dos) bajos Puente fijado en serie Subwoofers wired in Parallel Carga a 2Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono Input - - Only + + 2Ω 4Ω PARALLEL Jumper Plug Input Bi-Amp 2Ω Input - - Only + + 2Ω 4Ω 2Ω 2Ω JUMPER 1 amplificador monofónico 3 (Tres) bajos Puente fijado en serie Subwoofers wired in Parallel Carga a 1.3Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 2Ω 4Ω PARALLEL SERIES Jumper Plug Input - - Only + + JUMPER Input Bi-Amp 2Ω Input - - Only + + 2Ω 4Ω PARALLEL Jumper Plug Input Bi-Amp 2Ω Input - - Only + + 2Ω 4Ω 2Ω 1.3Ω JUMPER 1 amplificador monofónico 4 (Cuatro) bajos Puente fijado en serie Subwoofers wired in Parallel Carga a 1Ω SERIES JUMPER PARALLEL SERIES Jumper Plug Input Bi-Amp Mono 2Ω 4Ω - 2Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp 2Ω 4Ω 1Ω - - 14 - 2Ω PARALLEL SERIES Jumper Plug Input - Only + + JUMPER Input Bi-Amp Input - - Only + + 2Ω 4Ω 2Ω PARALLEL Jumper Plug Input Bi-Amp - Only + + 2Ω 4Ω Input - 2Ω Para instalar la caja sellada Cuando el altavoz no se pueda instalCuando el altavoz no se pueda instalCuando el altavoz no se pueda instalusar MDF—20 mm (3/4 pulg.) como material para la caja. CS-AW8520 & 8540 A 26-14/32 inch (671.8 mm) B 16-28/32 inch (429 mm) C 10-31/32 inch (278.9 mm) D 13-26/32 inch (351.2 mm) E 13-18/32 inch (370mm) F 4/32 inch (3 mm) G 2.205 ft3 (0.062 m3) Pantallas acústicas delantera y trasera (x 2) Lados superior e inferior (x 2) B G : El Volumen interior A Lados izquierdo y derecho (x 2) Dimensión del orificio de montaje * Tcrnillo: Dia. 4mm x 50mm (x 8) (suministrado) Para instalar la caja sellada Lados superior e inferior (x 2)Cuando el altavoz no se pueda instalar en el automóvil, construya la caja sellada recomendada en la tablade abajo—Asimismo, serecomienda usar CS-AW8520 & 8540 MDF—20 mm(3/4 pulg.) como material para la caja. A 26-14/32 inch (671.8 mm) B 16-28/32 inch (429 mm) C 10-31/32 inch (278.9 mm) D 13-26/32 inch (351.2 mm) E 13-18/32 inch (370mm) F 4/32 inch (3 mm) G 3 inch (76.2 mm) H 9 inch (228.6 mm) I 21 inch (533.4 mm) Pantallas acústicas delantera y trasera (x 2) J 3.255 ft3 (0.092 m3) C B Lados superior e inferior (x 2) J : El Volumen interior A G I * Tcrnillo: Dia. 4mm x 50mm (x 8) (suministrado) H - 15 - Lados izquierdo y derecho (x 2) Dimensión del orificio de montaje ESPAŃOL C Impedancia nominal (Ω) SPL (dB,1W/1M) Desplazamiento (litro) Diámetro del orificio cortado (pulgada) (mm) Profundidad de montaje (pulgada) (mm) CS-AW8040 parallel series 2Ω + 2Ω 88.09 dB 82.65 dB 0.403 ft3 Dia. 13 - 30/32 inch ( 354 mm ) 9 - 22/32 inch ( 245.85 mm ) Re (Ω) 1.03 Ω 3.99 Ω BL (T.M) 10.71 21.39 Vas (litro) 88.99 L 89.16 L Vas (pies cúbicos) Me (g) D (mm) 3.14 ft3 3.14 ft3 128.94 g 126.28 g Dia. 253 mm CS-AW8240 NOTAS parallel series 4Ω + 4Ω 86.14 dB 86.27dB SPL : Nivel de presión de sonido 0.403 ft3 Dia. 13 - 30/32 inch ( 354 mm ) 9 - 22/32 inch ( 245.85 mm ) Re : Resistencia de la bobina móvil de 2.07 Ω 8.17 Ω CC BL : Producto de densidad de flujo y 11.5 22.85 longitud efectiva del cable de la bobina móvil Vas: Volumen de aire equivalente en 160.534 L 106.92 L conformidad con el excitador 3.78 ft3 3.8 ft3 257.37 g 267.4 g Me : Masa efectiva Dia. 253 mm D : Diámetro efectivo del cono Fs (Hz) 27.7 Hz 27.7 Hz 26.7 Hz 26.7 Hz Qms 6.396 6.413 6.507 6.381 Qes 0.466 0.453 0.69 0.71 Qts 0.434 0.423 0.67 0.68 ESPAŃOL Parámetros Pe [máx.] (W) 1500 W 1500 W Xmax. (mm) 20.8 mm 20.8 mm 30 ~500 Hz 308.94 oz ( 8757.96 g ) Dia. 3 - 7/32 inch ( 80.54 mm ) 51.6 mm 10 mm 30 ~500 Hz 308.94 oz ( 8757.96 g ) Dia. 3 - 7/32 inch ( 80.54 mm ) 51.6 mm 10 mm Respuesta de frec (Hz) Masa del imán (oz) (g) Diám.de la bobina móvil (pulgada) (mm) Hvc (mm) Hag (mm) - 16 - Fs : Resonancia del aire sin excitador Qms : Q del excitador a Fs considerando sólo la resistencia no eléctrica Qes : Q del excitador a Fs considerando sólo la resistencia eléctrica Qts : Total Q dei excitador a Fs Pe[max.] : Potencia máxima de entrada contínua Xmax. : Máximo desplazamiento efectivo de la bobina móvil sin distorsón Hvc : Altura de bobina móvil Hag : Altura de entrehierro Santoprene Surround Multi Mount Smart Trim Ring (Patent Pending) Air Vented Aluminum Cast Basket Kevlar Laminated Hemp-Fiber Cone Integrated Dual-Layer Cone construction Hemp-Fiber Drive Cone Woven Tinsel Lead (Patent Pending) Dual Diametric Progressive Spider Rapid Fire Impedance Selector Speaker Terminal ( Patent Pending) Aluminum Voice Coil Former 4 (2+2) Layer Voice Coils Triple Stacked Strontium Magnet Heat Transfer Silicon Heat Transfer Silicon Aero Vent Bottom Plate T3 Chassis (Thermal Transfer Technology) ES OL h inc ] H 2 m h 7/3 .5 m nc a. 6i ] Di [ 5 1 / 8m -9 14 0 m a. [ 37 Di 9-21/32 inch [ 245.6 mm ] 1-9/32 inch [ 40.58 mm ] Dia. 15-9/16 inch [ 395 mm ] Dia. 16-1/32 inch [ 407.4 mm ] CS-AW8520 & 8540 Dia. 13-23/32 inch [ 348.54 mm ] - 17 - - 18 - TO OUR VALUED CUSTOMER THANK YOU FOR PURCHASING THIS JVC PRODUCT. WE WANT TO HELP YOU ACHIEVE A PERFECT EXPERIENCE. NEED HELP O N HOW TO HOOK UP? NEED ASSISTANCE ON HOW TO OPERATE? NEED TO LOCATE A JVC SERVICE CENTER? LIKE TO PURCHASE ACCESSORIES? IS HERE TO HELP! TOLL FREE: 1(800)252-5722 http://w )ww.jvc.com Remember to retain your Bill of Sale for Warranty Service. Do not attempt to service the product yourself Caution To prevent electrical shock, do not open the cabinet. There are no user serviceable parts inside. Please refer to qualified service personnel for repairs. EN, FR, SP © 2007 Victor Company of Japan, Limited Printed in China ">
Link pubblico aggiornato
Il link pubblico alla tua chat è stato aggiornato.